You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 4 Next »

Documentation

 

Generation 2 to generation 3 migration (firmware + driver)

  video play list.

Migration from the second generation (aka DEWESoft) to the third generation (aka TE USB FX2) of Trenz Electronic USB FX2 technology stack (firmware and driver).

TE0300: migration from 2nd to 3rd generation (firmware + driver)

This video shows how to upgrade a Trenz Electronic TE0300 device form the second to the third generation (firmware and driver). The video has been recorded on a Microsoft Windows 7 (64 bit) operating system with a TE0300-01 FPGA module connected to a USB port, but the procedure is almost the same for any Trenz Electronic USB FX2 device.

In this video, power-on reset is used.

Please note that TE0300 has master reset, thus a powered reset (S2 switch) is possible.

TE0320: migration from 2nd to 3rd generation (firmware + driver)

This video shows how to upgrade a Trenz Electronic TE0320 device form the second to the third generation (firmware and driver). The video has been recorded on a Microsoft Windows 7 (64 bit) operating system with a TE0320 FPGA module connected to a USB port, but the procedure is almost the same for any Trenz Electronic USB FX2 device.

In this video, power-on reset is used.

Please note that TE0320 has master reset, thus a powerered reset ( S1D switch to ON) is possible.

TE0630: migration from 2nd to 3rd generation (firmware + driver)

This video shows how to upgrade a Trenz Electronic TE0630 device form the second to the third generation (firmware and driver). The video has been recorded on a Microsoft Windows 7 (64 bit) operating system with a TE0630-00 FPGA module connected to a USB port, but the procedure is almost the same for any Trenz Electronic USB FX2 device.

Please note that, unlike TE0300 and TE0320, TE0630-00 has no -master reset-, thus a power-on reset is required.

Cypress USB Console used for 2nd to 3rd generation update.

This video explains how to use -Cypress USB Console- instead of "Cypress Control Center".

This video assumes that you have followed the first 6 minutes of "generation 2 to generation 3" videos (for anyone of the Trenz Electronic USB FX2 modules).

This video is an extension to 6:00 to 6:40 of "generation 2- to -generation 3" videos.

Description

When migrating from the second generation of the software stack for Trenz Electronic FPGA modules with USB interface (aka DEWESoft firmware and DEWESoft driver derivative) to the third generation (aka Trenz Electronic firmware and Cypress driver derivative), we recommend the following:

  • A) flash latest firmware into the module:

https://github.com/Trenz-Electronic/TE-USB-Suite/tree/master/TE_USB_FX2.firmware/ready_for_download/
(currently: TE-USB-FX2_v03.02_TE.iic)

  • B) fully uninstall (i.e. with "delete files" option activated on Windows Vista or later versions, in Windows XP the deletion must be done manually: see section 4) old driver and install new driver:

http://www.trenz-electronic.de/download/d0/Trenz_Electronic/d1/TE-USB-Suite/d2/generation_3/d3/drivers.html
and, of course, read carefully the manual (UM-drivers-TE_USB_FX2.pdf)
Driver installation on Microsoft Window 7 and Microsoft Window 8 can be performed automatically (on-line). It is possible that the first online driver installation fails; in this case the developer shall force a retry (the second attempt normally works). See UM-Drivers-TE_USB_FX2 manual at section 2.1.2.3.2 Force the online search.
Please compare your Device Manager window with the pictures shown in the manual cited above. In particular, check that the picture shown in section 2.1.3 Common to Windows XP/7/8 (Final Part) matches both device class name and driver class name in your Device Manager. If not, this is probably because the operating system links/loads the old driver class and driver file(s). In this case, it might be useful to go to C:\WINDOWS\system32\drivers (or the like) and delete TE03xx* files. The intended driver file names are "TE_USB_FX2_xx" instead:

  • TE_USB_FX2.cat
  • TE_USB_FX2.inf
  • TE_USB_FX2_32.sys
  • TE_USB_FX2_64.sys

Warning: Generation 3 device drivers with version date prior to 06 September 2012 must not be used.

On the GitHub repository, the developer can find the current C++/C# API. The code is associated with Microsoft Visual Studio Express 2010 project. This project can also be opened in Visual Studio Professional 2010.
The C++ DLL and sample code is preset for Microsoft Windows 32 bit operating systems. If you desire to compile the solution for 64 bit operating systems, the procedure in Microsoft Visual Studio Express and Microsoft Visual Studio Professional has some differences and is specified in Appendix A : Open the Visual Studio 2010 project of C++ TE_USB_FX2 API - reference manual published here: http://www.trenz-electronic.de/download/d0/Trenz_Electronic/d1/TE-USB-Suite/d2/generation_3/d3/APIs.html
The differences are the following

  • Express requires the installation of Microsoft Windows SDK 7.1 and it must be selected under Platform Toolset as Windows7.1SDK;
  • Professional uses the same v100 (10.0) runtime components as in Platform Toolset. The developer does not need to install Microsoft Windows SDK 7.1.

It is possible to download some Microsoft Visual Studio 2010 Express projects already correctly configured (for Microsoft Visual Studio 2010 Express 32/64 bit and Microsoft Visual Studio 2010 Professional 64 bit) from here:

  • No labels