Design Name is always "TE Series Name" + Design name, for example "TE0720 Test Board"

Important General Note:

• Export PDF to download, if vivado revision is changed!

• Designate all graphics and pictures with a number and a description, Use "Scroll Title" macro

  • Use "Scroll Title" macro for pictures and table labels. Figure number must be set manually at the moment (automatically enumeration is planned by scrollPDF)

    • Figure template (note: inner scroll ignore/only only with drawIO object):

      Create DrawIO object here: Attention if you copy from other page, use image link to the generate DrawIO PNG file of this page. This is a workaround until scroll pdf export bug is fixed

      
      

    • Table template:

      • Layout macro can be use for landscape of large tables
      • Set column width manually(can be used for small tables to fit over whole page) or leave empty (automatically)

    • 
      

      Example Comment 1 2

      
      

• ...

Table of contents

Notes :

• short description of the design

• Short Link of "Scroll only" macro:

  • Use short link the Wiki Resource page, for example: http://trenz.org/te0720-info

  • List of available short links: https://wiki.trenz-electronic.de/display/CON/Redirects

Notes :

• Add basic key futures, which can be tested with the design

• Vitis/Vivado 2020.2
• PetaLinux
• SD
• 2x ETH (Independent MDIO Interface and DP83848 PHY)
• I2C
• RTC
• Special FSBL for QSPI programming

Notes :

• add every update file on the download
• add design changes on description

• add known Design issues and general notes for the current revision
• do not delete known issue, add fixed version time stamp if  issue fixed

Notes :

• list of software which was used to generate the design

Notes :

• list of software which was used to generate the design

^{*used as reference}

Notes :

• content of the zip file

Notes :

• prebuilt files
• Template Table:

  • 
    

    File File-Extension Description BIF-File *.bif File with description to generate Bin-File BIN-File *.bin Flash Configuration File with Boot-Image (Zynq-FPGAs) BIT-File *.bit FPGA (PL Part) Configuration File Boot Source *.scr Distro Boot file DebugProbes-File *.ltx Definition File for Vivado/Vivado Labtools Debugging Interface Debian SD-Image *.img Debian Image for SD-Card Diverse Reports --- Report files in different formats Hardware-Platform-Description-File *.xsa Exported Vivado hardware description file for Vitis and PetaLinux LabTools Project-File *.lpr Vivado Labtools Project File MCS-File *.mcs Flash Configuration File with Boot-Image (MicroBlaze or FPGA part only) MMI-File *.mmi File with BRAM-Location to generate MCS or BIT-File with *.elf content (MicroBlaze only) OS-Image *.ub Image with Linux Kernel (On Petalinux optional with Devicetree and RAM-Disk) Software-Application-File *.elf Software Application for Zynq or MicroBlaze Processor Systems SREC-File *.srec Converted Software Application for MicroBlaze Processor Systems

    
    

• Important set new Vivado version link on every Design update of new vivado version!
• Set Link to download folder (Remove ../de/.. ../en/.. from url) for example: https://shop.trenz-electronic.de/Download/?path=Trenz_Electronic/Modules_and_Module_Carriers/4x5/TE0712/Reference_Design/2018.2/test_board

• Basic Design Steps

• Add/ Remove project specific description

Reference Design is available with and without prebuilt files. It's recommended to use TE prebuilt files for first lunch.

MIO Bank 501 Power is Carrier depends and set to 3.3V. Please check Settings, if you use a own carrier.

Caution! Win OS has a 260 character limit for path lengths which can affect the Vivado tools. To avoid this issue, use Virtual Drive or the shortest possible names and directory locations for the reference design (for example "x:\<project folder>")

Note:

• Programming and Startup procedure

Check Module and Carrier TRMs for proper HW configuration before you try any design.

Reference Design is also available with prebuilt files. It's recommended to use TE prebuilt files for first launch.

Note:

• Description of Block Design, Constrains... BD Pictures from Export...

Note:

• optional for Zynq / ZynqMP only

• add basic PS configuration

#
# Common bitgen related settings
#

set_property BITSTREAM.GENERAL.COMPRESS TRUE [current_design]
set_property CONFIG_VOLTAGE 3.3 [current_design]
set_property CFGBVS VCCO [current_design]

set_property BITSTREAM.CONFIG.USR_ACCESS TIMESTAMP [current_design]

#############
#ETH0/ETH1
#####
#pwr_down
set_property PACKAGE_PIN L21 [get_ports {PHY_PD[0]}]
set_property PACKAGE_PIN R20 [get_ports {PHY_PD[1]}]
#rst_n
set_property PACKAGE_PIN M15 [get_ports {PHY_RSTN[0]}]
set_property PACKAGE_PIN R16 [get_ports {PHY_RSTN[1]}]
#io standard
set_property IOSTANDARD LVCMOS33 [get_ports {PHY*}]
set_property IOSTANDARD LVCMOS33 [get_ports MDIO_*]
set_property IOSTANDARD LVCMOS33 [get_ports {MII_*}]
#pullup/down for PHY address 1
set_property PULLUP   true [get_ports MII_col]
set_property PULLDOWN true [get_ports {MII_rxd[0]}]
set_property PULLDOWN true [get_ports {MII_rxd[1]}]
set_property PULLDOWN true [get_ports {MII_rxd[2]}]
set_property PULLDOWN true [get_ports {MII_rxd[3]}]
#pullup/down for PHY address 3
set_property PULLUP true [get_ports MII_1_col]
set_property PULLUP true [get_ports {MII_1_rxd[0]}]
set_property PULLDOWN true [get_ports {MII_1_rxd[1]}]
set_property PULLDOWN true [get_ports {MII_1_rxd[2]}]
set_property PULLDOWN true [get_ports {MII_1_rxd[3]}]

#############
#ETH0
#####
set_property PACKAGE_PIN M16 [get_ports MDIO_ETHERNET_0_mdio_io]
set_property PACKAGE_PIN P16 [get_ports MDIO_ETHERNET_0_mdc]
set_property PACKAGE_PIN M22 [get_ports {MII_txd[3]}]
set_property PACKAGE_PIN K21 [get_ports {MII_txd[2]}]
set_property PACKAGE_PIN M17 [get_ports {MII_txd[1]}]
set_property PACKAGE_PIN J22 [get_ports {MII_txd[0]}]
set_property PACKAGE_PIN J20 [get_ports {MII_rxd[3]}]
set_property PACKAGE_PIN J18 [get_ports {MII_rxd[2]}]
set_property PACKAGE_PIN K18 [get_ports {MII_rxd[1]}]
set_property PACKAGE_PIN L17 [get_ports {MII_rxd[0]}]
set_property PACKAGE_PIN L16 [get_ports MII_col]
set_property PACKAGE_PIN N15 [get_ports MII_crs]
set_property PACKAGE_PIN L18 [get_ports MII_rx_clk]
set_property PACKAGE_PIN P15 [get_ports MII_rx_dv]
set_property PACKAGE_PIN P17 [get_ports MII_rx_er]
set_property PACKAGE_PIN K19 [get_ports MII_tx_clk]
set_property PACKAGE_PIN J21 [get_ports MII_tx_en]

#############
#ETH1
#####
set_property PACKAGE_PIN T16 [get_ports MDIO_ETHERNET_1_mdio_io]
set_property PACKAGE_PIN T17 [get_ports MDIO_ETHERNET_1_mdc]
set_property PACKAGE_PIN R21 [get_ports {MII_1_txd[3]}]
set_property PACKAGE_PIN P22 [get_ports {MII_1_txd[2]}]
set_property PACKAGE_PIN P21 [get_ports {MII_1_txd[1]}]
set_property PACKAGE_PIN N22 [get_ports {MII_1_txd[0]}]
set_property PACKAGE_PIN T19 [get_ports {MII_1_rxd[3]}]
set_property PACKAGE_PIN T18 [get_ports {MII_1_rxd[2]}]
set_property PACKAGE_PIN R19 [get_ports {MII_1_rxd[1]}]
set_property PACKAGE_PIN R18 [get_ports {MII_1_rxd[0]}]
set_property PACKAGE_PIN P20 [get_ports MII_1_col]
set_property PACKAGE_PIN N18 [get_ports MII_1_crs]
set_property PACKAGE_PIN M19 [get_ports MII_1_rx_clk]
set_property PACKAGE_PIN N17 [get_ports MII_1_rx_dv]
set_property PACKAGE_PIN P18 [get_ports MII_1_rx_er]
set_property PACKAGE_PIN N19 [get_ports MII_1_tx_clk]
set_property PACKAGE_PIN M21 [get_ports MII_1_tx_en]

• optional chapter separate

• sections for different apps

----------------------------------------------------------

FPGA Example

scu

MCS Firmware to configure SI5338 and Reset System.

srec_spi_bootloader

TE modified 2020.2 SREC

Bootloader to load app or second bootloader from flash into DDR

Descriptions:

• Modified Files: blconfig.h, bootloader.c
• Changes:
  
  • Add some console outputs and changed bootloader read address.
  • Add bugfix for 2018.2 qspi flash

xilisf_v5_11

TE modified 2020.2 xilisf_v5_11

• Changed default Flash type to 5.

----------------------------------------------------------

Zynq Example:

fsbl

TE modified 2020.2 FSBL

General:

• Modified Files: main.c, fsbl_hooks.h/.c (search for 'TE Mod' on source code)

• Add Files: te_fsbl_hooks.h/.c (for hooks and board)

• General Changes: 
  
  • Display FSBL Banner and Device ID

Module Specific:

• Add Files: all TE Files start with te_*
  
  • READ MAC from EEPROM and make Address accessible by UBOOT (need copy defines on uboot platform-top.h)
  • CPLD access
  • Read CPLD Firmware and SoC Type
  • Configure Marvell PHY

fsbl_flash

TE modified 2020.2 FSBL

General:

• Modified Files: main.c
• General Changes:
  
  • Display FSBL Banner
  • Set FSBL Boot Mode to JTAG
  • Disable Memory initialisation

ZynqMP Example:

----------------------------------------------------------

zynqmp_fsbl

TE modified 2020.2 FSBL

General:

• Modified Files: xfsbl_main.c, xfsbl_hooks.h/.c, xfsbl_board.h/.c (search for 'TE Mod' on source code)
• Add Files: te_xfsbl_hooks.h/.c (for hooks and board)
• General Changes: 
  
  • Display FSBL Banner and Device Name

Module Specific:

• Add Files: all TE Files start with te_*
  
  • Si5338 Configuration
  • ETH+OTG Reset over MIO

zynqmp_fsbl_flash

TE modified 2020.2 FSBL

General:

• Modified Files: xfsbl_initialisation.c, xfsbl_hw.h, xfsbl_handoff.c, xfsbl_main.c
• General Changes:
  
  • Display FSBL Banner
  • Set FSBL Boot Mode to JTAG
  • Disable Memory initialisation

zynqmp_pmufw

Xilinx default PMU firmware.

----------------------------------------------------------

General Example:

hello_te0820

Hello TE0820 is a Xilinx Hello World example as endless loop instead of one console output.

u-boot

U-Boot.elf is generated with PetaLinux. Vitis is used to generate Boot.bin.

• optional chapter separate

• sections for linux

• Add "No changes." or "Activate: and add List"

/include/ "system-conf.dtsi"
/ {
};
 
/* QSPI PHY */
&qspi {
    #address-cells = <1>;
    #size-cells = <0>;
    status = "okay";
    flash0: flash@0 {
        compatible = "jedec,spi-nor";
        reg = <0x0>;
        #address-cells = <1>;
        #size-cells = <1>;
    };
};
 

/* SDIO */
 
&sdhci0 {
   disable-wp;
};
 

/* ETH PHY */
 
&gem0{
    status = "okay";
    phy-mode = "mii";
    phy-handle = <&phy1>;
    xlnx,has-mdio = <0x1>;
    mdio {
        #address-cells = <1>;
        #size-cells = <0>;
        phy1: phy@1 {
            device_type = "ethernet-phy";
            compatible = "ethernet-phy-id2000.5C90";
        max-speed = <0x64>;
            reg = <1>;
        };
    };
};
 
 
&gem1{
    status = "okay";
    phy-mode = "mii";
    phy-handle = <&phy3>;
    xlnx,has-mdio = <0x1>;
    mdio {
        #address-cells = <1>;
        #size-cells = <0>;
        phy3: phy@3 {
            device_type = "ethernet-phy";
        compatible = "ethernet-phy-id2000.5C90";
        max-speed = <0x64>;
            reg = <3>;
        };
    };
};
 
 
/* RTC */
&i2c0 {
    rtc@56 {        // Real Time Clock
       compatible = "rv3029c2";
       reg = <0x56>;
   };
  
};      

• Add description for other Software, for example SI CLK Builder ...
• SI5338 and SI5345 also Link to:
  • Si5345
  • Si5338

• Note this list must be only updated, if the document is online on public doc!
• It's semi automatically, so do following
  

  • Add new row below first

  • Copy "Page Information Macro (date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description. --> this point is will be deleted on newer pdf export template

  • Metadata is only used of compatibility of older exports