Figure 1: TE0703 (REV 01).

Overview

Features

  1. VG96 Connectors (Mounting Holes and Solder Pads)
  2. Carrier Controller CPLD (Lattice LCMXO2-1200HC)

  3. SD Card level-shifter

  4. Micro SD Card Connector
  5. LEDs
  6. Mini USB Connector FT2232H
  7. User Push Button 
  8. RJ45 GbE Connector
  9. USB Host Connector
  10. Barrel jack for 5V Power Supply
  11. 4A High-Efficiency DC-DC Step-Down Converter for 3.3V Power Supply
  12. Trenz 4x5 Module Socket (3x Samtec LSHM Series Connectors)
  13. USB JTAG and UART Interface (FTDI FT2232H), compatible with Xilinx Tools
  14. DIP Switch

Note: TE0703 must be powered by a 5V power supply!

 

User I/O Connectors

Note: VCCIO for FPGA banks is has no default fixed connection to power supply. Those the bank VCCIO must be supplied to externally, or optionally 0 ohm resistors can be soldered onto TE0703 to set fixed 3.3V voltages.

Example wiring that powers ALL banks with 3.3V - those connections should be present on the base board, in this drawing 3 banks are have VCCIO supplied over connector and 4th bank is connected to 3.3V with jumper J5.

 

TE0715-30 modification

 

REMOVE jumper J5, add wires as on picture for VCCIO=1.8V for all banks.

UART

FT2232H USB interface Channel B is normally used as UART, in default CPLD configuration UART pins are routed to Module connector to location of default UART pins.

FT2232H Channel BB2BTE0715TE0720TE0710TE0711TE0712TE0713TE0741Notes
TXDJM1.92MIO14MIO14A8N17P16A10J21Module input
RXDJM1.85MIO15MIO15B8R10U18C11G24Module output

LEDS

Two LED's (those closer to mini-USB Connector) are connected to the 4x5 B2B Connector pins. Those LEDs can be controlled by FPGA Module.

LEDNet NameColorB2B/ModuleTE0710TE0711TE0712TE0713TE0715TE0720TE0741
D3FLED1RedJM2.100U8F5J16U8H6U7U21
D4FLED2GreenJM2.89K6J5M17K6H5R7Y20
The bank where LED's are is not powered when TE0703 is used in standalone mode. VCCIO for this bank must be supplied back to the TE0703 connectors. TE0703 header Pin J2.B1 must have some valid I/O voltage or the LED's will not be lit. To connect 3.3V to this bank install 0R or solder bridge to empty place of R26 on the bottom of the PCB.
If the Bank where LED's are has VCCIO 1.8V then the LED's will lit with very low intensity.

Two LED's closer to the micro SD Card are connected to CPLD and not Module Connectors, their function depends on the CPLD Version.

   Notes
D1ULED1RedFTDI UART Receive activity
D2ULED2GreenFTDI UART Transmit activity

Default function of the User LED's. Note the function of this LEDs is controlled by the CPLD and can be changed.

 I2C Level Shifter

TE0703 has a I2C level shifter IC on-board, there are however no I2C devices on TE0703. Those pins that go through level shifter can be used I2C bus, or as GPIO.

Net B2B/ModuleTE0715TE0720TE0710TE0711TE0712TE0713TE0741
SCL JM1.95MIO10MIO10R10M13T21B9L22
SDA JM1.93MIO11MIO11L18L18Y22A9K21

Micro SD Card Socket

The Micro SD Card Socket do not include a Card detect signal and Write Protect signal. It is not directly connected to the 4x5 B2B Connector pins, but through a SDIO port expander, TI TXS02612. This device is used for voltage translation, due to the different voltage levels between Micro SD Card and MIO Bank 501 on the Zynq 7000 . (The Micro SD Card is 3.3V, but the MIO Bank 501 is set to 1.8V.)

Signal NameDescriptionNet NameB2B/ModuleTE0715TE0720
DATA[3]DataDAT3JM1.17MIO45MIO45
DATA[2]DataDAT2JM1.19MIO44MIO44
DATA[1]DataDAT1JM1.21MIO43MIO43
DATA[0]DataDAT0JM1.23MIO42MIO42
CMDCommandCMDJM1.25MIO41MIO41
CLKClockS_CLKJM1.27MIO40MIO40

DIP Switch settings

 

4MODE = LOWMODE = HIGHModule "MODE" Pin level, select between boot-modes (SPI <> SD for Zynq modules)
3Normal modeCC Update modeJTAG Select: fixed function can not be changed
2   
1   

Function of MODE pin is module dependent!

Carrier Controller Update Mode 

Carrier Controller JTAG port is enabled by setting switch 3 on DIP switch S2 on TE0703 to "OFF" position. This setting is only useful when updating Carrier Controller firmware! In this mode Module JTAG is not accessible.

 

Switch 3 on DIP switch S2 must be moved to "ON" position for normal operation! Otherwise the JTAG on the module would not be accessible at all.

Configuring B34 Bank Supply for TE0720 Zynq SoC Module 

J5 Jumper can be used to power TE0720 bank 34 from TE0720 3.3V output rail. If J5 is installed TE0720 will boot also in the case bank 34 supply is not delivered from the VG96 /Pin headers. If TE0720 bank supply of 3.3V is required it is recommended to insert the jumper. Optionally, 3.3V or any other valid IO voltage can be supplied from the TE0703 pins.

Use with TE0715

Care should be taken with TE0715-30, all I/O should be set to 1.8V

 

Backup Battery Supply (VBAT connector)

J7 provides two pins (+/-) to supply battery backup voltage to TE0720. If not required leave open.

 
Ensure to connect the supply battery to jumper J7 with correct polarity!

Revision History

REV 04

Document Change History

daterevisionauthorsdescription
2014-02-12

Antti Lukats, Sven-Ole Voigt

Work in progress
 

All