Online version of this document and other related documents can be found at https://wiki.trenz-electronic.de/display/PD/TEP0001. |
Integrated 12 kV IEC-61000-4-2 ESD contact discharge protection
J1. Screw connector terminal of CAN0 bus
J2. 2.54mm pitch 2x6-pin header Pmod interface
J3. 2.54mm pitch 2x5-pin box header, CAN0 bus
J4. 2.54mm pitch 2x5-pin box header, CAN1 bus
J5. 2.54mm pitch SMT 2x3-pin jumper block, can also be used as CAN1 bus connector
J6. 2.54mm pitch SMT 2x3-pin jumper block, can also be used as CAN0 bus connector
U1. Texas Instruments TCAN337G CAN FD transceiver, CAN0
D1. Bourns CDSOT23-T24CAN CANbus Protector, CAN0
U2. Texas Instruments TCAN337G CAN FD transceiver, CAN1
D2. Bourns CDSOT23-T24CAN CANbus Protector, CAN1
TEP0001 PMOD connector is mounted for Right Angle connection to PMOD Baseboard. |
Pin | Signal | Notes |
---|---|---|
1 | CAN0_H | U1 high level CAN bus line |
2 | GND | U1 ground connection |
3 | CAN0_L | U1 low level CAN bus line |
Pin | Signal | Notes | Pin | Signal | Notes | |
---|---|---|---|---|---|---|
1 | CAN0_TX | U1 CAN0 transmit data input, integrated pull up | 2 | CAN1_TX | U2 CAN1 transmit data input, integrated pull up | |
3 | CAN0_RX | U1 CAN0 receive data output, tri-state | 4 | CAN1_RX | U2 CAN1 receive data output, tri-state | |
5 | CAN0_S | U1 silent mode,integrated pull down | 6 | CAN1_S | U2 silent mode, integrated pull down | |
7 | CAN0_F | U1 open drain fault output | 8 | CAN1_F | U2 open drain fault output | |
9 | GND | U1 ground connection | 10 | GND | U2 ground connection | |
11 | 3.3V | U1 3.3V supply voltage | 12 | 3.3V | U2 3.3V supply voltage |
Pin | Signal | Notes | Pin | Signal | Notes | |
---|---|---|---|---|---|---|
1 | N/A | - | 2 | GND | U1 ground connection | |
3 | CAN0_L | U1 low level CAN bus line | 4 | CAN0_H | U1 high level CAN bus line | |
5 | GND | U1 ground connection | 6 | N/A | - | |
7 | N/A | - | 8 | N/A | - | |
9 | N/A | - | 10 | N/A | - |
Pin | Signal | Notes | Pin | Signal | Notes | |
---|---|---|---|---|---|---|
1 | N/A | - | 2 | GND | U2 ground connection | |
3 | CAN1_L | U2 low level CAN bus line | 4 | CAN1_H | U2 high level CAN bus line | |
5 | GND | U2 ground connection | 6 | N/A | - | |
7 | N/A | - | 8 | N/A | - | |
9 | N/A | - | 10 | N/A | - |
Close pins 1-3 and 2-4 with jumpers to enable on-board terminator for CAN1 bus. J5 header can also be used as CAN1 bus connector, refer to the following table pin mapping.
Pin | Signal | Note | Pin | Signal | Note | |
---|---|---|---|---|---|---|
3 | CAN1_L | U2 low level CAN bus line | 4 | CAN1_H | U2 high level CAN bus line | |
5 | GND | U2 ground connection | 6 | GND | U2 ground connection |
Close pins 1-3 and 2-4 with jumpers to enable on-board terminator for CAN0 bus. J6 header can also be used as CAN0 bus connector, refer to the following table for pin mapping.
Pin | Signal | Note | Pin | Signal | Note | |
---|---|---|---|---|---|---|
3 | CAN0_L | U1 low level CAN bus line | 4 | CAN0_H | U1 high level CAN bus line | |
5 | GND | U1 ground connection | 6 | GND | U1 ground connection |
Minimum | Maximum | Unit | |
---|---|---|---|
Supply voltage | 3 | 3.6 | V |
Operational free-air temperature | -40 | 125 | °C |
Parameter | Minimum | Maximum | Unit |
---|---|---|---|
Supply voltage range | -0.3 | 5 | V |
Voltage at any bus terminal (CANH or CANL) | -14 | 14 | V |
Operating temperature range | -40 | 150 | °C |
Storage temperature | - | 150 | °C |
Refer to Texas Instruments TCAN337G product datasheet for additional information about conditions and ratings. |
3.3V supply voltage TBD* (180 mA max per one CAN FD transceiver in "Normal Mode", dominant state with bus fault as per TCAN337G datasheet).
* TBD - To Be Determined soon with reference design setup.
Module size: 54 mm × 20.5 mm.
Mating height of the J2 connector from the PCB: 8mm
PCB thickness: 1.6mm
Highest parts on PCB are J1, J3 and J4 connectors, approximately 9.5mm from the PCB.
Date | Rrevision | Contributors | Description |
---|---|---|---|
05.09.2016 | Initial document. |
Date | Revision | Notes | PCN |
---|---|---|---|
22.08.2016 | 01 | Initial batch | - |
Hardware revision number is printed on the PCB board next to the module model number separated by the dash.