Download PDF Version of this Document. |
Table of Contents |
Refer to https://shop.trenz-electronic.de/de/Download/?path=Trenz_Electronic/ for downloadable version of this manual and additional technical documentation of the product. |
The Trenz Electronic ... is an industrial-grade ... based on ...
Put your block diagram here...
Put top and bottom pics with labels of the real PCB here...
Add description list of PCB labels here...
List key features here, like FPGA type, amount and type of RAM, type of flash, etc.
Additional assembly options are available for cost or performance optimization upon request.
Storage device name | Content | Notes |
---|---|---|
|
|
I/O signals connected to the SoC's I/O bank and B2B connector:
Bank | Type | B2B Connector | I/O Signal Count | Voltage | Notes |
---|---|---|---|---|---|
For detailed information about the pin out, please refer to the Pin-out Tables.
MIO | Function | B2B Pin | Notes | MIO | Function | B2B Pin | Notes | |
---|---|---|---|---|---|---|---|---|
On board Gigabit Ethernet PHY is provided with ...
Ethernet PHY connection
PHY Pin | PS | PL | Notes |
---|---|---|---|
USB PHY is provided with ...
PHY Pin | Pin | B2B Name | Notes |
---|---|---|---|
The schematics for the USB connector and required components is different depending on the USB usage. USB standard A or B connectors can be used for Host or Device modes. A Mini USB connector can be used for USB Device mode. A USB Micro connector can be used for Device mode, OTG Mode or Host Mode.
On-board I2C devices are connected to MIO.. and MIO.. which are configured as I2C... by default. I2C addresses for on-board devices are listed in the table below:
I2C Device | I2C Adress | Notes |
---|---|---|
JTAG access to the ... is provided through B2B connector ....
JTAG Signal | B2B Connector Pin |
---|---|
TCK | |
TDI | |
TDO | |
TMS |
JTAGEN pin in B2B connector ... should be kept low or grounded for normal operation. |
Special purpose pins are connected to smaller System Controller CPLD and have following default configuration:
Pin Name | Mode | Function | Default Configuration |
---|---|---|---|
PGOOD | Output | Power Good | Active high when all on-module power supplies are working properly. |
JTAGEN | Input | JTAG Select | Low for normal operation. |
By default the ... supports QSPI and SD Card boot modes which is controlled by the MODE input signal from the B2B connector.
MODE Signal State | Boot Mode |
---|---|
high or open | SD Card |
low or ground | QSPI |
LED | Color | Connected to | Description and Notes |
---|---|---|---|
Name | IC | ID | PS7 | MIO | Notes |
---|---|---|---|---|---|
SPI Flash | S25FL256SAGBHI20 | U14 | QSPI0 | MIO1..MIO6 |
Clock | Frequency | IC | FPGA | Notes |
---|---|---|---|---|
PS CLK | 33.3333 Mhz |
| PS_CLK | PS subsystem main clock. |
GT REFCLK1 | 125 Mhz |
| Default clock is 125 MHz. |
An temperature compensated ... is used for Real Time Clock ...
There is a I2C programmable clock generator ... chip on the ...
PLL connection
I/O | Default Frequency | Notes |
---|---|---|
A ... EEPROM (U..) is used which contains a globally unique 48-bit node address, that is compatible with EUI-48(TM) and EUI-64(TM) specification.
Power supply with minimum current capability of ...A for system startup is recommended.
Power Consumption
Power Input Pin | Max Current |
---|---|
VIN | TBD* |
3.3VIN | TBD* |
* TBD - To Be Determined soon with reference design setup.
For highest efficiency of on board DC/DC regulators, it is recommended ...
Voltages on B2B- Connectors | B2B | B2B | B2B | Input/ Output | Note |
---|---|---|---|---|---|
Bank | Schematic Name | Voltage | TE0715-xx-15 | TE0715-xx-30 |
---|---|---|---|---|
... put some B2B related information here if you have them ...
Please take care, B2B connectors are of interest when on module. B2B on baseboard has no meaning for the user of the baseboard.
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
VIN supply voltage | V | - | ||
Storage temperature | -40 | +85 | °C | - |
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
VIN supply voltage |
Assembly variants for higher storage temperature range are available on request. |
Module size: ... mm × ... mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: ... mm.
PCB thickness: ... mm.
Highest part on PCB: approx. ... mm. Please download the step model for exact numbers.
All dimensions are given in mm.
Put mechanical drawings here...
Commercial grade: 0°C to +70°C.
Industrial grade: -40°C to +85°C.
Operating temperature range depends also on customer design and cooling solution. Please contact us for options.
... g - Plain ...
... g - Set of bolts and nuts
Date | Revision | Notes | PCN | Documentation link |
---|---|---|---|---|
- | 01 | Prototypes |
Hardware revision number is printed on the PCB board together with the module model number separated by the dash.
Put pic of PCB silk screen here showing model and revision ...
Date | Revision | Contributors | Description |
---|---|---|---|
2016-11-30 | Jan Kumann
| Initial Document |