Overview

Refer to http://trenz.org/te0715-info for the current online version of this manual and other available documentation.

Key Features

Revision History

Release Notes and Know Issues

Requirements

Software

Hardware

Complete List is available on "<project folder>\board_files\*_board_files.csv"

Design supports following modules:

Design supports following carriers:

Additional HW Requirements:

Content

For general structure and usage of the reference design, see Project Delivery - AMD devices

Design Sources

Additional Sources

Prebuilt

Download

Reference Design is only usable with the specified Vivado/Vitis/PetaLinux version. Do never use different Versions of AMD Software for the same Project.

Reference Design is available on:

• TE0715 "Test Board" Reference Design

Design Flow

Trenz Electronic provides a tcl based built environment based on AMD Design Flow.

See also:

• AMD Development Tools#AMDSoftware-BasicUserGuides
• Vivado Projects - TE Reference Design
• Project Delivery.

The Trenz Electronic FPGA Reference Designs are TCL-script based project. Command files for execution will be generated with "_create_win_setup.cmd" on Windows OS and "_create_linux_setup.sh" on Linux OS.

TE Scripts are only needed to generate the vivado project, all other additional steps are optional and can also executed by AMD Vivado/Vitis GUI.  For currently Scripts limitations on Win and Linux OS see: Project Delivery Currently limitations of functionality

1. Run _create_win_setup.cmd/_create_linux_setup.sh and follow instructions on shell:

   ------------------------Set design paths---------------------------- -- Run Design with: _create_win_setup -- Use Design Path: <absolute project path> -------------------------------------------------------------------- -------------------------TE Reference Design--------------------------- -------------------------------------------------------------------- -- (0) Module selection guide, project creation...prebuilt export... -- (1) Create minimum setup of CMD-Files and exit Batch -- (2) Create maximum setup of CMD-Files and exit Batch -- (3) (internal only) Dev -- (4) (internal only) Prod -- (c) Go to CMD-File Generation (Manual setup) -- (d) Go to Documentation (Web Documentation) -- (g) Install Board Files from AMD Board Store (beta) -- (a) Start design with unsupported Vivado Version (beta) -- (x) Exit Batch (nothing is done!) ---- Select (ex.:'0' for module selection guide):

   
   

2. Press 0 and enter to start "Module Selection Guide"
3. Create project and follow instructions of the product selection guide, settings file will be configured automatically during this process.
   

   • optional for manual changes: Select correct device and AMD install path on "design_basic_settings.cmd" and create Vivado project with "vivado_create_project_guimode.cmd"

     Note: Select correct one, see also Vivado Board Part Flow

     
     

4. Create hardware description file (.xsa file) for PetaLinux project and export to prebuilt folder

   TE::hw_build_design -export_prebuilt

   
   

   Using Vivado GUI is the same, except file export to prebuilt folder.

   
   

5. Create and configure your PetaLinux project with exported .xsa-file, see PetaLinux KICKstart
   • use TE Template from "<project folder>\os\petalinux"

   • use exported .xsa file from "<project folder>\prebuilt\hardware\<short name>" . Note: HW Export from Vivado GUI creates another path as default workspace.

   • The build images are located in the "<plnx-proj-root>/images/linux" directory

6. Configure the boot.scr file as needed, see Distro Boot with Boot.scr
   

7. Copy PetaLinux build image files to prebuilt folder

   • copy u-boot.elf, u-boot.dtb, system.dtb, image.ub and boot.scr from "<plnx-proj-root>/images/linux" to prebuilt folder
     

     "<project folder>\prebuilt\os\petalinux\<ddr size>" or "<project folder>\prebuilt\os\petalinux\<short name>"

     
     

     This step depends on AMD Device/Hardware for Zynq-7000 series copy u-boot.elf, u-boot.dtb, system.dtb, image.ub and boot.scr from "<plnx-proj-root>/images/linux" to prebuilt folder for ZynqMP copy u-boot.elf, u-boot.dtb, system.dtb, bl31.elf, image.ub and boot.scr from "<plnx-proj-root>/images/linux" to prebuilt folder for Microblaze ...

     
     

8. Generate Programming Files with Vitis

   TE::sw_run_vitis -all TE::sw_run_vitis (optional; Start Vitis from Vivado GUI or start with TE Scripts on Vivado TCL)

   
   

   TCL scripts generate also platform project, this must be done manually in case GUI is used. See Vitis

   
   

Launch

Programming

AMD documentation for programming and debugging: Vivado/Vitis/SDSoC-Xilinx Software Programming and Debugging

Get prebuilt boot binaries

1. Run _create_win_setup.cmd/_create_linux_setup.sh and follow instructions on shell
2. Press 0 and enter to start "Module Selection Guide"
   1. Select assembly version
   2. Validate selection

   3. Select Create and open delivery binary folder

      Note: Folder "<project folder>\_binaries_<Article Name>" with subfolder "boot_<app name>" for different applications will be generated

      
      

QSPI-Boot mode

Optional for Boot.bin on QSPI Flash and image.ub and boot.scr on SD or USB.

1. Connect JTAG and power on carrier with module

2. Open Vivado Project with "vivado_open_existing_project_guimode.cmd" or if not created, create with "vivado_create_project_guimode.cmd"

   TE::pr_program_flash -swapp u-boot TE::pr_program_flash -swapp hello_te0715 (optional)

   
   

3. Copy image.ub and boot.scr on SD or USB
   
   • use files from "<project folder>\_binaries_<Article Name>\boot_linux" from generated binary folder,see: Get prebuilt boot binaries
   • or use prebuilt file location, see "<project folder>\prebuilt\file_location.txt"
4. Set Boot Mode to QSPI-Boot and insert SD or USB.
   • Depends on Carrier, see carrier TRM.

SD-Boot mode

1. Copy image.ub, boot.scr and Boot.bin on SD
   • use files from "<project folder>\_binaries_<Article Name>\boot_linux" from generated binary folder,see: Get prebuilt boot binaries
   • or use prebuilt file location, see "<project folder>\prebuilt\file_location.txt"
   • optional: use startup script init.sh for SD
2. Set Boot Mode to SD-Boot.
   • Depends on Carrier, see carrier TRM.
3. Insert SD-Card in SD-Slot.

JTAG

Not used on this Example.

Usage

1. Prepare HW like described on section Programming
2. Connect UART USB (most cases same as JTAG)

3. Select SD Card as Boot Mode (or QSPI - depending on step 1)

   Note: See TRM of the Carrier, which is used.

   
   

   Starting with Petalinux version 2020.1, the industry standard "Distro-Boot" boot flow for U-Boot was introduced, which significantly expands the possibilities of the boot process and has the primary goal of making booting much more standardised and predictable. The boot options described above describe the common boot processes for this hardware; other boot options are possible. For more information see Distro Boot with Boot.scr

   
   

4. Power On PCB

   1. Zynq Boot ROM loads FSBL from SD/QSPI into OCM, 2. FSBL init PS, programs PL using the bitstream and loads U-boot from SD into DDR, 3. U-boot loads Linux (image.ub) from SD/QSPI/... into DDR

   
   

   This step depends on AMD Device/Hardware for Zynq-7000 series 1. Zynq Boot ROM loads FSBL from SD/QSPI into OCM, 2. FSBL init the PS, programs the PL using the bitstream and loads U-boot from SD/QSPI into DDR, 3. U-boot loads Linux (image.ub) from SD/QSPI/... into DDR for ZynqMP??? 1. ZynqMP Boot ROM loads FSBL from SD/QSPI into OCM, 2. FSBL init the PS, programs the PL using the bitstream and loads PMU, ATF and U-boot from SD/QSPI into DDR, 3. U-boot loads Linux (image.ub) from SD/QSPI/... into DDR for Microblaze with Linux 1. FPGA Loads Bitfile from Flash, 2. MCS Firmware configure SI5338 and starts Microblaze, (only if mcs is available) 3. SREC Bootloader from Bitfile Firmware loads U-Boot into DDR (This takes a while), 4. U-boot loads Linux from QSPI Flash into DDR for native FPGA ...

   
   

Linux

1. Open Serial Console (e.g. putty)
   
   • Speed: 115200

   • select COM Port

     Win OS, see device manager, Linux OS see dmesg | grep tty  (UART is *USB1)

     
     

2. Linux Console:
   

   Note: Wait until Linux boot finished

   
   

3. You can use Linux shell now.
   

   i2cdetect -y -r 0 (check I2C 1 Bus) dmesg | grep rtc (RTC check) udhcpc (ETH0 check) lsusb (USB check)

   
   

4. Option Features
   • Webserver to get access to Zynq
     • insert IP on web browser to start web interface
   • init.sh scripts
     • add init.sh script on SD, content will be load automatically on startup (template included in "<project folder>\misc\SD")

Vivado HW Manager 

• Monitoring:
  
  • Si5338 CLKs:
    • Set radix from VIO signals to unsigned integer. Note: Frequency Counter is inaccurate and displayed unit is Hz
    • MGT CLK is configured to 125MHz by default, FCLK is not configured by default (optionally possible over FSBL → 50MHz on delivered configuration, see FSBL description).

System Design - Vivado

Block Design

PS Interfaces

Activated interfaces:

Constraints

Basic module constraints

set_property BITSTREAM.GENERAL.COMPRESS TRUE [current_design]
set_property CONFIG_VOLTAGE 3.3 [current_design]
set_property CFGBVS VCCO [current_design]

set_property BITSTREAM.CONFIG.USR_ACCESS TIMESTAMP [current_design]

set_property BITSTREAM.CONFIG.UNUSEDPIN PULLNONE [current_design]

Design specific constraints

set_property PACKAGE_PIN K2 [get_ports {fclk[0]}]
set_property IOSTANDARD LVCMOS18 [get_ports {fclk[0]}]
set_property CLOCK_DEDICATED_ROUTE FALSE [get_nets fclk_IBUF[0]]

# for fmeter only
set_false_path -from [get_clocks clk_fpga_0] -to [get_clocks mgt_clk1_clk_p]
set_false_path -from [get_clocks mgt_clk1_clk_p] -to [get_clocks clk_fpga_0]

Software Design - Vitis

For Vitis project creation, follow instructions from:

Vitis

Application

fsbl

TE modified 2022.2 FSBL

General:

• Modified Files: main.c, fsbl_hooks.h/.c (search for 'TE Mod' on source code)

• Add Files: te_fsbl_hooks.h/.c (for hooks and board)

• General Changes: 
  
  • Display FSBL Banner and Device ID

Module Specific:

• Add Files: all TE Files start with te_*
  
  • SI5338 Configuration

fsbl_flash

TE modified 2022.2 FSBL

General:

• Modified Files: main.c
• General Changes:
  
  • Display FSBL Banner
  • Set FSBL Boot Mode to JTAG
  • Disable Memory initialisation

hello_te0715

Hello TE0715 is a AMD Hello World example as endless loop instead of one console output.

u-boot

U-Boot.elf is generated with PetaLinux. Vitis is used to generate Boot.bin.

Software Design -  PetaLinux

For PetaLinux installation and project creation, follow instructions from:

• PetaLinux KICKstart

Config

Start with petalinux-config or petalinux-config --get-hw-description

Changes:

• CONFIG_SUBSYSTEM_ETHERNET_PS7_ETHERNET_0_MAC=""

U-Boot

Start with petalinux-config -c u-boot

Changes:

• CONFIG_QSPI_BOOT=y
• CONFIG_SD_BOOT=y
• CONFIG_ENV_IS_NOWHERE=y
• CONFIG_ENV_OVERWRITE=y                       (used to overwrite environment parameter)
• CONFIG_ENV_IS_IN_FAT=y                           (needed to boot from SD card)
• CONFIG_ENV_IS_IN_SPI_FLASH=y                  (needed to boot from QSPI flash)
• # CONFIG_ENV_IS_IN_NAND is not set
• CONFIG_BOOT_SCRIPT_OFFSET=0x1920000   (Calculate the start address of partition 3 "bootscr" in the QSPI flash. To do this, add the sizes of partitions 0, 1 and 2 together)
• CONFIG_ZYNQ_MAC_IN_EEPROM=y
• CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET=0xFA
• CONFIG_SYS_I2C_EEPROM_ADDR=0x50

Device Tree (system-user.dtsi in device-tree and uboot-device-tree)

/include/ "system-conf.dtsi"
/ {
  chosen {
    xlnx,eeprom = &eeprom;
  };
};
 
/*------------------- default --------------------*/
 
/*------------------ QSPI PHY --------------------*/
&qspi {
    #address-cells = <1>;
    #size-cells = <0>;
    status = "okay";     
flash0: flash@0 {
        spi-rx-bus-width = <4>;
        spi-tx-bus-width = <4>;
        compatible = "jedec,spi-nor";
        reg = <0x0>;
        #address-cells = <1>;
        #size-cells = <1>;
    };
};
 
 
 
/*--------------------- ETH PHY ------------------*/
&gem0 {
 
    status = "okay";
        ethernet_phy0: ethernet-phy@0 {
        compatible = "marvell,88e1510";
        device_type = "ethernet-phy";
                reg = <0>;
    };
};
 
 
/*---------------------- USB PHY -----------------*/ 
/{
    usb_phy0: usb_phy@0 {
        compatible = "ulpi-phy";
        //compatible = "usb-nop-xceiv";
        #phy-cells = <0>;
        reg = <0xe0002000 0x1000>;
        view-port = <0x0170>;
        drv-vbus;
    };
};
 
&usb0 {
    dr_mode = "host";
    //dr_mode = "peripheral";
    usb-phy = <&usb_phy0>;
};
 
/*---------------------- I2C ---------------------*/
// i2c PLL: 0x70, i2c eeprom: 0x50
 
&i2c1 {
  rtc@6F {                      // Real Time Clock
       compatible = "isl12022";
       reg = <0x6F>;
   };
  
  eeprom: eeprom@50 {           //MAC EEPROM
    compatible = "atmel,24c08";
    reg = <0x50>;
  };
};

FSBL patch

Must be add manually --> work in progress

Kernel

Start with petalinux-config -c kernel

Changes:

• CONFIG_RTC_DRV_ISL12022=y

Rootfs

Start with petalinux-config -c rootfs

Changes:

• CONFIG_i2c-tools=y
• CONFIG_busybox-httpd=y         (for web server app)
• CONFIG_usbutils=y
• CONFIG_util-linux-umount=y      (uses mount/umount function from util-linux instead of busybox)
• CONFIG_util-linux-mount=y
• CONFIG_auto-login=y 

Applications

See "<project folder>\os\petalinux\project-spec\meta-user\recipes-apps\"

startup

Script App to load init.sh from SD Card if available.

webfwu

Webserver application suitable for Zynq access. Need busybox-httpd

Additional Software

SI5338

File location "<project folder>\misc\Si5338\Si5338-*.slabtimeproj"

General documentation how you work with this project will be available on Si5338

Appx. A: Change History and Legal Notices

Document Change History

To get content of older revision  got to "Change History" of this page and select older document revision number.

v.13

Legal Notices