In this section you must explain how to power on the board and run the Reference Design (test board) on the particular module. The main points must be mentioned are: |
Table of Contents |
TEF1002
Overview
- 4x5 module connectors
- Jumper J4 (VCCIOA)
- Jumper J7 (VCCA_SD)
- Dip swiches S2 and S3
- 6-pin PCI-E ATX Power Connector
- micro USB connector for FTDI USB to JTAG/UART bridge
- Push button
- Power LED
- Status LED
- top load microSD card cage
- Select Voltage VCCA_SD of 4x5 module bank where SD-Card is connected by Jumper J7 (1-2 →3.3V; 2-3 1.8V). Compare TRM of actually used 4x5 module.
- Select VCCIOA Voltage by setting J4 (1-2 →3.3V; 2-3 1.8V). If both FFA and FFB are not used any setting is ok. Do not leave open (communication of 4x5 module with TEF1002 CPLD is only possible with availabe VCCIOA)!
Dip | Setting | Note |
---|
S1 |
| Push button configured as reset |
S2-1 | OFF | FMC _VADJ OFF. The choice OFF, ON, OFF selects 1.8V FMC_VADJ, wich is a valid bank power for TE0720.
|
S2-2 | OFF |
S2-3 | OFF |
S2-4 | ON | Selects 4x5 module SOC/FPGA JTAG |
S2-5 | ON |
S2-6 | OFF |
S2-7 | ON | Module power enable. |
S2-8 | ON | Use extended power sequenzing. |
S3-1 | OFF/ON | For Zynq modules: Primary Boot Mode SD/QSPI. |
S3-2 | OFF | ON for TE0720 (overide automatic enable FMC__VADJ). For TE0720 bank bank 34 has to be powerded to start up. Therefore FMC VADJ has to be set to a valid value e.g. 1.8V |
- Connect 12V ATX connector
- Connect mico USB J10 to PC
- Use Xilinx JTAG tools to programm FPGA or for Zynq modules use micro SD Card.
- Use e.g. Putty on PC to check for UART interactions.
Power supply
The input power supply must be mentioned. |
Single 12V power supply with minimum current capability of 3A is recommended to power on the board.
DIP-Switches and Push Buttons
Explain all DIP switches functionality. |
Select dip switch settings according to the attached 4x5 module and your needs
There is a switch (S??) which is connected to RESET signal, it resets the system entirely.
Signal | Designator | B2B | Active Level |
---|
|
|
|
|
|
Jumpers
Explain all Jumpers functionality and connection. |
Designator | Connected to | B2B | Note |
---|
| Boot_R |
| Open: | Short: |
|
LEDs
Explain all user LEDs functionality and connections. |
There are three user LEDs which can be used for variant purposes.
Designator | Color | Connected to | B2B | Active Level | Note |
---|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Designator | Color | Connected to | Active Level | Note |
---|
|
|
|
|
|
|
|
|
|
|
|
Designator | Color | Connected to | Active Level | Note |
---|
|
|
|
|
|
|
|
|
|
|
|
JTAG/UART
Explain JTAG or UART connection breifly. |
JTAG and UART connections are available through mini USB connector.
JTAG(first FTDI port) and UART(second FTDI port) is over MicroUSB connector possible. External JTAG Programmer is not needed.
Designator | Connected to | B2B Pin | XMOD Header JB? | Direction | Note |
---|
|
|
|
|
|
|
|
|
|
|
|
|
|
Reference Designs
In this Section you must refer to the Reference Design (Test board) for the particular module. For Example: TE0728 Reference Designs |
Notes
In this Section you must refer to the Resources Page for the particular module. For Example: TE0728 Resources |