Template Revision 2.12
- Module: TRM Name always "TE Series Name" +TRM
Example: "TE0728 TRM" - Carrier: TRM Name usually "TEB Series Name" +TRM
Example: "TEB0728 TRM"
|
<!-- tables have all same width (web max 1200px and pdf full page(640px), flexible width or fix width on menu for single column can be used as before) -->
<style>
.wrapped{
width: 100% !important;
max-width: 1200px !important;
}
</style> |
----------------------------------------------------------------------- |
Note for Download Link of the Scroll ignore macro: |
Table of Contents |
Overview
The Trenz Electronic TEP0006 is a Ultra96 LS Expansion to Pmod adapter.
Refer to http://trenz.org/tep0006-info for the current online version of this manual and other available documentation.
Key Features
Note: 'description: Important components and connector or other Features of the module → please sort and indicate assembly options Key Features' must be split into 6 main groups: - FPGA/Module
- Package:
- Speed:
- Temperature:
- RAM/Storage
- On Board
- Interface
- E.g. ETH, USB, B2B, Display port
- Power
- E.g. Input supply voltage
- Dimension
|
- On Board:
- 4x Voltage Level Translators
- 2x Voltag Regulators
- Interface:
- 1x LS Expansion Header (40 Pins)
- 3x Pmod Connectors
- 3x Jumpers
- Power:
- Dimension:
Block Diagram
Main Components
Notes : - Picture of the PCB (top and bottom side) with labels of important components
- Add List below
|
- PMod 2x6 Host Socke (PMOD 2) ,J2
- PMod 2x6 Host Socke (PMOD 2) ,J1
- Level Translator (HP_GPIO[0..7]) ,U1
- Level Translator (HP_GPIO[8..15]),U3
- Level Translator PMOD(SPI),U6
- Linear Voltage Regulator,U2
- Jumper,J6-J7
- PMod 2x6 Host Socke (SPI),J4
- GROVE,J5
- Level Translator (GROVE) ,U5
- Jumper (Voltage select ),J10
- SMD Header 40 Pos. (LS Expansion ),J3
Initial Delivery State
Notes : Only components like EEPROM, QSPI flash can be initialized by default at manufacture. If there is no components which might have initial data ( possible on carrier) you must keep the table empty |
Storage device name | Content | Notes |
---|
--- | --- | --- |
|
Configuration Signals
- Overview of Boot Mode, Reset, Enables.
|
Signals, Interfaces and Pins
Notes : - For carrier or stand-alone boards use subsection for every connector type (add designator on description, not on the subsection title), for example:
- For modules which needs carrier use only classes and refer to B2B connector if more than one is used, for example
|
Low Speed Expansion Connector
General information about GPIO connection to the LS Expansion connector:
Schematic | Connected to | Notes |
---|
HD_GPIO0...7 | Level Translator HP_GPIO[0...7], U1 | GPIO | HD_GPIO8...15 | Level Translator HP_GPIO[8...15], U3 | GPIO | MIO36-37 | Level Translator PMOD(SPI) | GPIO0-GPIO1 | MIO38, MIO41...43 | Level Translator PMOD(SPI) | SPI | VCC_PSAUX | Level Translator, U1-U3-U5-U6 Voltage Regulator, U2 | 1.8 V | 5V | Voltage Regulator, U2 Jumper, J10 |
|
|
Pmod Connectors
The TEP0006 is equipped with three Pmod connectors.
Pin | Pmod 1, J1 | Pmod 2, J2 | Pmod SPI, J4 | Notes |
---|
1 | PMOD_HD-GPIO0 | PMOD_HD-GPIO8 | SS |
| 2 | PMOD_HD-GPIO1 | PMOD_HD-GPIO9 | MOSI |
| 3 | PMOD_HD-GPIO2 | PMOD_HD-GPIO10 | MISO |
| 4 | PMOD_HD-GPIO3 | PMOD_HD-GPIO11 | SCK |
| 5 | GND | GND | GND |
| 6 | 3.3 V | 3.3 V | 3.3 V |
| 7 | PMOD_HD-GPIO4 | PMOD_HD-GPIO12 | INIT |
| 8 | PMOD_HD-GPIO5 | PMOD_HD-GPIO13 | RESET |
| 9 | PMOD_HD-GPIO6 | PMOD_HD-GPIO14 | Not Connected |
| 10 | PMOD_HD-GPIO7 | PMOD_HD-GPIO15 | Not Connected |
| 11 | GND | GND | GND |
| 12 | 3.3 V | 3.3 V | 3.3 V |
|
|
Jumpers
Designator | Functionality | Connection Between | Notes |
---|
J6 |
| HD_GPIO_15 VCC_PSAUX |
| J7 |
| HD_GPIO_15 VCC_PSAUX |
| J10 | Voltage select | SDA 5 V, 3.3 V | SDA can be either 5 V or 3.3 V |
|
On-board Peripherals
Notes : - add subsection for every component which is important for design, for example:
- Two 100 Mbit Ethernet Transciever PHY
- USB PHY
- Programmable Clock Generator
- Oscillators
- eMMCs
- RTC
- FTDI
- ...
- DIP-Switches
- Buttons
- LEDs
|
Notes : In the on-board peripheral table "chip/Interface" must be linked to the corresponding chapter or subsection |
Chip/Interface | Designator | Notes |
---|
-- | -- | -- |
|
Power and Power-On Sequence
In 'Power and Power-on Sequence' section there are three important digrams which must be drawn: - Power on-sequence
- Power distribution
- Voltage monitoring circuit
|
Power Supply
Power supply with minimum current capability of 1 A for system startup is recommended.
Power Consumption
Power Input Pin | Typical Current |
---|
VIN | TBD* |
|
* TBD - To Be Determined
Power Distribution Dependencies
Power-On Sequence
There is no specific power on sequence, after power on all electrical components will be enabled.
Power Rails
Power Rail Name | LS Expansion Connector Pin | Direction | Notes |
---|
+5V | 37 | Input |
| VCC_PSAUX | 35 | Output |
|
|
Technical Specifications
Absolute Maximum Ratings
Symbols | Description | Min | Max | Unit |
---|
Vin | Input Supply Voltage | 1.7 | 5.5 | V | T_STG | Storage Temperature | -55 | 150 | °C |
|
Recommended Operating Conditions
Operating temperature range depends also on customer design and cooling solution. Please contact us for options.
Parameter | Min | Max | Units | Reference Document |
---|
Vin | 4.5 | 5.5 | V | See MAX8902BATA+T datasheet. | T_OPT | -40 | +85 | °C |
|
|
Physical Dimensions
PCB thickness: 1.6 mm.
Currently Offered Variants
Revision History
Hardware Revision History
Date | Revision | Changes | Documentation Link |
---|
2019-07-19 | 01 | Initial Release | REV01 |
|
Hardware revision number can be found on the PCB board together with the module model number separated by the dash.
Document Change History
- Note this list must be only updated, if the document is online on public doc!
- It's semi automatically, so do following
Add new row below first Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description. --> this point is will be deleted on newer pdf export template - Metadata is only used of compatibility of older exports
|
Date | Revision | Contributor | Description |
---|
| | | | -- | all | | |
|
Disclaimer