Template Revision 2.6 - on construction

Design Name always "TE Series Name" + Design name, for example "TE0720 Test Board"

<!-- tables have all same width (web max 1200px and pdf full page(640px), flexible width or fix width on menu for single column can be used as before) -->
<style>
.wrapped{
  width: 100% !important;
  max-width: 1200px !important;
 }
</style>

Important General Note:

• Export PDF to download, if vivado revision is changed!

• Designate all graphics and pictures with a number and a description, Use "Scroll Title" macro

  • Use "Scroll Title" macro for pictures and table labels. Figure number must be set manually at the moment (automatically enumeration is planned by scrollPDF)

    • Figure template (note: inner scroll ignore/only only with drawIO object):

      Create DrawIO object here: Attention if you copy from other page, use image link to the generate DrawIO PNG file of this page. This is a workaround until scroll pdf export bug is fixed

      
      

    • Table template:

      • Layout macro can be use for landscape of large tables
      • Set column width manually(can be used for small tables to fit over whole page) or leave empty (automatically)

    • 
      

      Example Comment 1 2

      
      

• ...

Table of contents

Notes :

• short description of the design

• Short Link of "Scroll only" macro:

  • Use short link the Wiki Resource page, for example: http://trenz.org/te0720-info

  • List of available short links: https://wiki.trenz-electronic.de/display/CON/Redirects

Notes :

• Add basic key futures, which can be tested with the design

• 2018.3
• PetaLinux
• SD
• ETH
• USB
• I2C
• Special FSBL for QSPI programming

Notes :

• add every update file on the download
• add design changes on description

• add known Design issues and general notes for the current revision
• do not delete known issue, add fixed version time stamp if  issue fixed

Notes :

• list of software which was used to generate the design

Notes :

• list of software which was used to generate the design

Notes :

• content of the zip file

Notes :

• prebuilt files
• Template Table:

  • 
    

    File File-Extension Description BIF-File *.bif File with description to generate Bin-File BIN-File *.bin Flash Configuration File with Boot-Image (Zynq-FPGAs) BIT-File *.bit FPGA (PL Part) Configuration File DebugProbes-File *.ltx Definition File for Vivado/Vivado Labtools Debugging Interface Debian SD-Image *.img Debian Image for SD-Card Diverse Reports --- Report files in different formats Hardware-Platform-Specification-Files *.hdf Exported Vivado Hardware Specification for SDK/HSI and PetaLinux LabTools Project-File *.lpr Vivado Labtools Project File MCS-File *.mcs Flash Configuration File with Boot-Image (MicroBlaze or FPGA part only) MMI-File *.mmi File with BRAM-Location to generate MCS or BIT-File with *.elf content (MicroBlaze only) OS-Image *.ub Image with Linux Kernel (On Petalinux optional with Devicetree and RAM-Disk) Software-Application-File *.elf Software Application for Zynq or MicroBlaze Processor Systems SREC-File *.srec Converted Software Application for MicroBlaze Processor Systems

    
    

• Important set new Vivado version link on every Design update of new vivado version!
• Set Link to download folder (Remove ../de/.. ../en/.. from url) for example: https://shop.trenz-electronic.de/Download/?path=Trenz_Electronic/Modules_and_Module_Carriers/4x5/TE0712/Reference_Design/2018.2/test_board

• Basic Design Steps

• Add/ Remove project specific description

Reference Design is available with and without prebuilt files. It's recommended to use TE prebuilt files for first lunch.

Note:

• Programming and Startup procedure

Check Module and Carrier TRMs for proper HW configuration before you try any design.

Note:

• Description of Block Design, Constrains... BD Pictures from Export...

Note:

• optional for Zynq / ZynqMP only

• add basic PS configuration

#
# Common BITGEN related settings for TE0726
#
set_property BITSTREAM.GENERAL.COMPRESS TRUE [current_design]
set_property CONFIG_VOLTAGE 3.3 [current_design]
set_property CFGBVS VCCO [current_design]

set_property BITSTREAM.CONFIG.UNUSEDPIN PULLUP [current_design]

• optional chapter separate

• sections for different apps

----------------------------------------------------------

FPGA Example

scu

MCS Firmware to configure SI5338 and Reset System.

srec_spi_bootloader

TE modified 2018.3 SREC

Bootloader to load app or second bootloader from flash into DDR

Descriptions:

• Modified Files: blconfig.h, bootloader.c
• Changes:
  
  • Add some console outputs and changed bootloader read address.
  • Add bugfix for 2018.2 qspi flash

xilisf_v5_11

TE modified 2018.3 xilisf_v5_11

• Changed default Flash type to 5.

----------------------------------------------------------

Zynq Example:

zynq_fsbl

TE modified 2018.3 FSBL

General:

• Modified Files:main.c, fsbl_hooks.h/.c (search for 'TE Mod' on source code)

• Add Files: te_fsbl_hooks.h/.c(for hooks and board)\n\

• General Changes: 
  
  • Display FSBL Banner and Device ID

Module Specific:

• Add Files: all TE Files start with te_*
  
  • READ MAC from EEPROM and make Address accessible by UBOOT (need copy defines on uboot  platform-top.h)
  • CPLD access
  • Read CPLD Firmware and SoC Type
  • Configure Marvell PHY

zynq_fsbl_flash

TE modified 2018.3 FSBL

General:

• Modified Files: main.c
• General Changes:
  
  •  Display FSBL Banner
  • Set FSBL Boot Mode to JTAG
  • Disable Memory initialisation

ZynqMP Example:

----------------------------------------------------------

zynqmp_fsbl

TE modified 2018.3 FSBL

General:

• Modified Files: xfsbl_main.c, xfsbl_hooks.h/.c, xfsbl_board.h/.c(search for 'TE Mod' on source code)
• Add Files:  te_xfsbl_hooks.h/.c (for hooks and board)\n\
• General Changes: 
  
  • Display FSBL Banner and Device Name

Module Specific:

• Add Files: all TE Files start with te_*
  
  • Si5338 Configuration
  • ETH+OTG Reset over MIO

zynqmp_fsbl_flash

TE modified 2018.3 FSBL

General:

• Modified Files: xfsbl_initialisation.c, xfsbl_hw.h, xfsbl_handoff.c, xfsbl_main.c
• General Changes:
  
  •  Display FSBL Banner
  • Set FSBL Boot Mode to JTAG
  • Disable Memory initialisation

zynqmp_pmufw

Xilinx default PMU firmware.

----------------------------------------------------------

General Example:

hello_te0820

Hello TE0820 is a Xilinx Hello World example as endless loop instead of one console output.

u-boot

U-Boot.elf is generated with PetaLinux. SDK/HSI is used to generate Boot.bin.

• optional chapter separate

• sections for linux

• Add "No changes." or "Activate: and add List"

/include/ "system-conf.dtsi"
/ {
};
 
 
/* USB PHY */
 
/{
    usb_phy0: usb_phy@0 {
        compatible = "ulpi-phy";
        #phy-cells = <0>;
        reg = <0xe0002000 0x1000>;
        view-port = <0x0170>;
        drv-vbus;
    };
};
 
&usb0 {
    dr_mode = "host";
    //dr_mode = "peripheral";
    usb-phy = <&usb_phy0>;
};
 
/* I2C1 */
 
&i2c1 {
    #address-cells = <1>;
    #size-cells = <0>;
 
    i2cmux0: i2cmux@70  {
        compatible = "nxp,pca9544";
        #address-cells = <1>;
        #size-cells = <0>;
        reg = <0x70>;
 
 
        i2c1@0 {
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <0>;
 
            id_eeprom@50 {
                compatible = "atmel,24c32";
                reg = <0x50>;
            };
 
        };
        i2c1@1 {    // Display Interface Connector
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <1>;
        };
        i2c1@2 {    // HDMI Interface Connector
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <2>;
        };
        i2c1@3 {    // Camera Interface Connector
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <3>;
        };
    };
 
};

• Add description for other Software, for example SI CLK Builder ...
• SI5338 and SI5345 also Link to:
  • Si5345
  • Si5338

• Note this list must be only updated, if the document is online on public doc!
• It's semi automatically, so do following
  

  • Add new row below first

  • Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description. --> this point is will be deleted on newer pdf export template

  • Metadata is only used of compatibility of older exports