| Company | Trenz Electronic GmbH |
|---|---|
| PCN Number | PCN-20230322 |
| Title | TE0722-02 to TE0722-03 Hardware Revision Change |
| Subject | Hardware Revision Change |
| Issue Date | 2023-06-01 |
Products Affected
This change affects all Trenz Electronic TE0722 SoMs: TE0722-02*.
Affected Product | Replacement |
|---|---|
| TE0722-02 | TE0722-03-41C-4-A |
| TE0722-02I | TE0722-03-41I-4-A |
| TE0722-02-07S-1C | TE0722-02-11C-4-A |
Changes
#1 Changed DCDC EN5311QI (U2, U3) to MPM3834CGPA and adapted power circuit.
Type: Schematic Change
Reason: EOL of Component.
Impact: None. Increased current output capability. Minor changes in electrical characteristics.
#2 Changed ferrid bead BKP0603HS121-T (L1, L2, L4, L5) to MPZ0603S121HT000.
Type: Schematic Change
Reason: EOL of Component.
Impact: None.
#3 Removed proximity/ambient light sensor Si1143-A11-GMR (U4).
Type: Schematic Change
Reason: EOL of Component.
Impact: Sensor is no longer available. Firmware reflects it but custom firmware needs to be updated by customer.
#4 Added resistors (R37, R38, R39) to prepare proximity/ambient light sensor (U4) circuit for Si115x usage.
Type: Schematic Change
Reason: EOL of Si1143-A11-GMR.
Impact: Sensor is no longer available. Firmware reflects it but custom firmware needs to be updated by customer.
#5 Changed MEMS oscillator (U8) from SiT8008AI-73-XXS-33.333333E to SiT8008BI-73-XXS-33.333333E.
Type: BOM change
Reason: EOL of Component.
Impact: None. Clock revision changed.
#6 Added jumper (J4) and resistor (R40) to enable JTAG only boot mode and changed resistor (R11) from 19.1 kOhm to 10 kOHm.
Type: Schematic Change
Reason: QSPI programming problems with newer Vivado versions.
Impact: None. Fix QSPI programming problems with newer Vivado versions according to AR#00002 - QSPI Programming issues.
#7 Renamed signal name from "SPI-DQ0/M0" to "SPI-DQ0/M3".
Type: Schematic Change
Reason: Use AMD boot mode name convention.
Impact: None.
#8 Renamed signal name from "SPI-DQ3/M3" to "SPI-DQ3/M0".
Type: Schematic Change
Reason: Use AMD boot mode name convention.
Impact: None.
#9 Modified testpoints : Added (TP4, TP5, TP6) / Changed size from 1 mm to 0.8 mm diameter (TP1, TP2, TP3, TP7). / Removed (TP8).
Type: PCB Change
Reason: Use standard testpoints.
Impact: None.
#10 Modified fiducials: Added (PM5, PM6) / Changed (PM1, PM2, PM3, PM4).
Type: PCB Change
Reason: Use standard fiducial setting.
Impact: None.
#11 Added CE and UKCA logo.
Type: PCB Change
Reason: Required logos.
Impact: None.
#12 Added legal notices, revision history, block and power diagram. Updated page count and order.
Type: Documentation Update
Reason: Documentation improvement.
Impact: None.
Method of Identification
The Revision number is printed on the top side of the PCB.
Production Shipment Schedule
From December 2023, after old stock is gone. If the new revision is not suitable for your application and still the former revision of the board is needed, please contact us.
Contact Information
If you have any questions related to this PCN, please contact Trenz Electronics Technical Support at
- forum.trenz-electronic.de
- wiki.trenz-electronic.de
- support%trenz-electronic.de (subject = PCN-20230322)
phone
national calls: 05741 3200-0
international calls: 0049 5741 3200-0
Disclaimer
Any projected dates in this PCN are based on the most current product information at the time this PCN is being issued, but they may change due to unforeseen circumstances. For the latest schedule and any other information, please contact your local Trenz Electronic sales office, technical support or local distributor.
This PCN follows JEDEC Standard J-STD-046.
Overview
Content Tools