Table of Contents
Overview
Trenz Electronic TE0711 is an industrial-grade FPGA module integrating a Xilinx Artix-7 FPGA, 32 MByte Quad SPI Flash memory for configuration and operation and powerful switching-mode power supplies for all on-board voltages. Numerous configurable I/O's are provided via rugged high-speed strips. All this on a tiny footprint, smaller than a credit card size at very competitive price. All Trenz Electronic SoM's in 4 x 5 cm form factor are mechanically compatible.
Block Diagram
Figure 1: TE0711-01 block diagram.
Main Components
Figure 2: TE0711 (REV 01).
- Artix-7 (15T to 100T) FPGA
- EN6347QI voltage Regulator 1.0V
- EN5311QI voltage Regulator 1.8V
- S25FL256S 32 MByte Quad SPI Flash memory
- Dual USB to UART/FIFO Bridge (FT2232H)
- TPS27082L load switch for 3.3V voltage level
- B2B connector JM1 (0,40 mm Razor Beam™ High Speed Hermaphroditic Terminal/Socket Strip (LSHM-150))
- B2B connector JM2 (0,40 mm Razor Beam™ High Speed Hermaphroditic Terminal/Socket Strip (LSHM-150))
- B2B connector JM3 (0,40 mm Razor Beam™ High Speed Hermaphroditic Terminal/Socket Strip (LSHM-150))
- System Controller CPLD (Lattice LCMXO2-256HC): 256 Macrocell CPLD
- SiT8008AI 100 MHz reference clock (connected to FPGA bank 14)
- SiT8008AI 12 MHz reference clock (connected to USB to UART/FIFO Bridge)
- EEPROM (configuration data for USB to UART/FIFO Bridge)
- TPS3805H33 voltage detector for generating "Power OK"-signal indicating successful power-on-sequencing
Key Features
Industrial-grade Xilinx Artix-7 (15T to 100T) SoM (System on Module), supported by the free Xilinx Vivado WebPACK tool
Rugged for shock and high vibration
- FTDI FT2232HQ USB 2.0 High Speed to UART/FIFO
32 MByte QSPI Flash memory (with XiP support)
100 MHz MEMS oscillator
Plug-on module with 2 × 100-pin and 1 × 60-pin high-speed hermaphroditic strips
178 FPGA I/Os (84 differential pairs) are available on board-to-board connectors
On-board high-efficiency DC-DC converters
4.0 A x 1.0 V power rail
1.0 A x 1.8 V power rail
1.0 A x 1.5 V power rail
System management and power sequencing
eFUSE bit-stream encryption
AES bit-stream encryption
User LED
Evenly-spread supply pins for good signal integrity
Assembly options for cost or performance optimization available upon request.
Initial Delivery State
Storage Component | Content | Notes |
---|---|---|
SPI Flash OTP Area | Empty, not programmed | Except serial number programmed by flash vendor. |
SPI Flash Quad Enable bit | Programmed | - |
SPI Flash main array | Demo design | - |
EFUSE USER | Not programmed | - |
EFUSE Security | Not programmed | - |
Table 1: TE0711 initial delivery state.
Signals, Interfaces and Pins
Board to Board (B2B) I/Os
I/O signals connected to the FPGA's I/O banks and B2B connector:
Bank | Type | B2B Connector | I/O Signal Count | Voltage | Notes |
---|---|---|---|---|---|
0 | HR | - | - | 3.3V | Configuration bank |
14 | HR | JM1 JM2 | 8 I/O pins 18 I/O pins, (9 LVDS pairs possible) | 3.3V | HR banks support voltages from 1.2V to 3.3V. See Xilinx Artix-7 datasheet (DS181) for voltage ranges. |
15 | HR | JM1 | 48 I/O pins 24 LVDS pairs possible | User | As above. |
16 | HR | JM1 | 6 I/O pins 3 LVDS pairs possible | 1.8V | As above. |
34 | HR | JM1 JM3 | 48 I/O pins 24 LVDS pairs possible | User | As above. |
35 | HR | JM2 | 50 I/O pins 24 LVDS pairs possible | User | As above. |
Table 2: Voltage ranges and pin-outs of available logic banks of the FPGA.
Please use Master Pin-out Table as primary reference for the pin mapping information.
JTAG Interface
JTAG access to the Xilinx Artix-7 and to the System Controller CPLD is provided through B2B connector JM2.
JTAG Signal | B2B Connector |
---|---|
TCK | JM2-99 |
TDI | JM2-95 |
TDO | JM2-97 |
TMS | JM2-93 |
Table 3: Pin-mapping of JTAG Interface on B2B connector
JTAGSEL pin on B2B connector JM1 is used to control which physical device is accessible via JTAG interface. If this pin is set to low or left open, JTAG interface is enabled for Xilinx Artix-7 FPGA, if set to high, JTAG interface for System Controller CPLD will be enabled.
The use of Xilinx legacy development tools (ISE, iMPACT) is not recommended. iMPACT does not recognize any Xilinx Artix-7 below A100T model.
System Controller I/O Pins
Special purpose pins are connected to smaller System Controller CPLD and have following default configuration:
Pin Name | Mode | Function | Default Configuration | B2B Connector |
---|---|---|---|---|
STAT_SC2 | Output | Power Good | Active high when all on-module power supplies are working properly. | JM1-30 |
NRST_SC0 | Input | Reset | Active low reset signal, drive low to keep the system in reset (FPGA pin PROG_B will be driven by CPLD) | JM2-18 |
JTAGSEL | Input | JTAG Select | Low for normal operation, high (3.3V) to programm the System Controller CPLD | JM1-89 |
EN_SC3 | Input | Enable FPGA Core Voltage supply | High (3.3V) or open for normal operation, low to stop power-on sequencing | JM1-28 |
Table 4: Pin-description of System Controller CPLD.
LEDs
The TE0711 SoM has total of 4 on-board LED's. LED's D1, D2 and D3 are connected to the Xilinx Artix-7 FPGA and can be freely used by user design. LED D4 is the System Controller CPLD status LED.
LED | Color | Connected to | Description and Notes |
---|---|---|---|
D1 | Red | SYSLED2 | User LED, active HIGH, connected to FPGA Pin A8 |
D2 | Green | SYSLED4 | User LED, active HIGH, connected to FPGA Pin R17 |
D3 | Green | SYSLED3 | User LED, active LOW, connected to FPGA Pin L15 |
D4 | Green | SYSLED1 | System Controller status LED, connected to CPLD |
Table 5: Description of on-board LED's.
Clocking
The TE0711 is equipped with MEMS oscillator (SiT8008AI-73-XXS-100.000000E, U8) to provide 100 MHz clock signal for Xilinx Artix-7 FPGA pin P17.
On-board Peripherals
32 MByte Quad SPI Flash Memory
On-board SPI flash memory S25FL256S (U7) is used to store initial FPGA configuration. Besides FPGA configuration, remaining free flash memory can be used for user application storage. All four SPI data lines are connected to the FPGA allowing x1, x2 or x4 data bus widths. Maximum data rate depends on the bus width and clock frequency used.
SPI Flash QE (Quad Enable) bit must be set to high or FPGA is unable to load its configuration from flash. By default this bit is set to high at the manufacturing plant.
System Controller
The system controller is used to coordinate the configuration of the FPGA. The FPGA is held in reset (by driving the PROG_B signal) until the power supplies have sequenced. Low level at NRST_SC0 pin also resets the FPGA. This signal can be driven from the user’s PCB via the B2B connector pin JM2-18. Input EN_SC3 is also gated to FPGA Reset and should be open or pulled up for normal operation. EN_SC3 low turns off on board DC-DC converters and stops power-on sequencing.
It is possible for the user to create their own system controller design using the Lattice Diamond software. Once created the design can be programmed into the device using the JTAG pins. The signal JTAGSEL should be set to 3.3V to enable programming mode. For normal operation it should be set to 0V.
There are one status LED connected to the system controller CPLD. When the FPGA is not configured the LED will flash continuously. Finally once FPGA configuration has completed the LEDs can be used in the user's FPGA design.
Dual channel USB to UART/FIFO
The TE0711-01 SoM has on-board high-speed USB 2.0 to UART/FIFO FT2232HQ controller from FTDI. Channel A can only be used in simple UART mode. Channel B can be used as UART in FT245 FIFO mode, JTAG (MPSSE) mode or in high-speed serial modes.
FT2232HQ controller is connected to the FPGA bank 14 with fixed 3.3V VCCIO and all signalling must meet the LVCMOS 3.3V I/O standard.
256 Byte EEPROM is connected to the FT2232HQ-chip to store custom configuration settings. These settings can be changed using FTDI provided tools that can be downloaded from FTDI website.
Power and Power-On Sequence
Power Supply
Power supply with minimum current capability of 2A for system startup is recommended.
Power Input Pin | Voltage Range | Max Current |
---|---|---|
VIN | 3.3V to 5.5V | Typical 200mA, depending on customer design and connections. |
3.3VIN | 3.3V | Typical 50mA, depending on customer design and connections. |
Table 6: Typical power consumption.
VIN and VIN3.3V can be connected to the same power source (3.3V).
Lowest power consumption is achieved when powering the module from single 3.3V supply. When using split 3.3V/5V supplies the power consumption (and heat dissipation) will rise, this is due to the DC/DC converter efficiency (it decreases when VIN/VOUT ratio rises).
Power-On Sequence
For highest efficiency of on board DC-DC regulators, it is recommended to use same 3.3V power source for both VIN and 3.3VIN power rails. Although VIN and 3.3VIN can be powered up in any order, it is recommended to power them up simultaneously.
It is important that all baseboard I/O's are 3-stated at power-on until System Controller sets STAT_SC2 signal high (B2B connector JM1, pin 30), or 3.3V is present on B2B connector JM2 pins 10,12 or 91, meaning that all on-module voltages have become stable and module is properly powered up.
See Xilinx Artix-7 datasheet DS181 for additional information. Also check related baseboard documentation when choosing baseboard design for TE0711-01 module.
A 3.3V supply is also needed and must be supplied from the user's PCB. An output 3.3V supply is available on some of the board connector pins (see section 'Power Rails'). The input 3.3VIN will be switched to the internal 3.3V voltage level after the FPGA 1.0V supply has stabilized. Than 3.3V supply will be available on the B2B connector pins.
The regulators can be powered from the 3.3V supply or a 5V supply if preferred. The options for powering the board are as follows:
- Apply 5V to pins VIN and 3.3V to pins 3.3VIN on the board connector
- Apply 3.3V to pins VIN and 3.3VIN on the board connectors.
Power Rails
Voltages on B2B- Connectors | B2B JM1-Pin | B2B JM2-Pin | Direction | Note |
---|---|---|---|---|
VIN | 1, 3, 5 | 2, 4, 6, 8 | input | supply voltage |
3.3VIN | 13, 15 | - | input | supply voltage |
VCCIO15 | 9, 11 | - | input | high range bank voltage |
VCCIO34 | - | 1, 3 | input | high range bank voltage |
VCCIO35 | 7, 9 | input | high range bank voltage | |
3.3V | 14 | 10, 12, 91 | output | internal 3.3V voltage level |
1.8V | 39 | - | output | internal 1.8V voltage level |
Table 7: Power rails of SoM on B2B connectors.
Bank Voltages
Bank | Schematic Name | Voltage | Range |
---|---|---|---|
0 Config | 3.3V | 3.3V | - |
14 | 3.3V | 3.3V | - |
15 | VCCIO15 | user | HR: 1.2V to 3.3V |
16 | 1.8V | 1.8V | - |
34 | VCCIO34 | user | HR: 1.2V to 3.3V |
35 | VCCIO35 | user | HR: 1.2V to 3.3V |
Table 8: Range of FPGA's bank voltages.
See the Artix7 datasheet DS181 for the allowable voltage range.
Board to Board Connectors
Variants Currently In Production
Module Variant | FPGA | FPGA Junction Temperature | Operating Temperature Range |
---|---|---|---|
TE0711-01-100-2C | XC7A100T-2CSG324C | 0°C to 85°C | Commercial grade |
TE0711-01-35-2C | XC7A35T-2CSG324C | 0°C to 85°C | Commercial grade |
TE0711-01-100-2I | XC7A100T-2CSG324I | -40°C to 100°C | Industrial grade |
TE0711-01-35-2I | XC7A35T-2CSG324I | -40°C to 100°C | Industrial grade |
Table 9: Differences between variants of Module TE0711-01
Technical Specifications
Absolute Maximum Ratings
Parameter | Min | Max | Units | Notes |
---|---|---|---|---|
VIN supply voltage | -0.3 | 7.0 | V | EN6347QI / EN5311QI data sheet |
3.3VIN supply voltage | -0.1 | 3.6 | V | - |
PL IO bank supply voltage for HR I/O Banks (VCCO) | -0.5 | 3.6 | V | - |
I/O input voltage for HR I/O banks | -0.4 | VCCO_X+0.55 | V | - |
Voltage on module JTAG pins | -0.5 | VCCO_0+0.45 | V | VCCO_0 is 3.3V nominal. |
Storage temperature | -55 | +125 | °C | - |
Table 10: Absolute maximum ratings.
Recommended Operating Conditions
Parameter | Min | Max | Units | Notes | Reference Document |
---|---|---|---|---|---|
VIN supply voltage | 2.4 | 5.5 | V | - | EN5311QI data sheet |
3.3VIN supply voltage | 3.135 | 3.465 | V | - | 3,3V ± 5% |
PL I/O bank supply voltage for HR I/O banks (VCCO) | 1.14 | 3.465 | V | - | Xilinx datasheet DS181 |
I/O input voltage for HR I/O Banks | - 0.20 | VCCO + 0.2 | V | - | Xilinx datasheet DS181 |
Voltage on Module JTAG pins | 3.135 | 3.465 | V | - | 3,3V ± 5% |
Table 11: Recommended operating conditions.
Operating Temperature Ranges
Commercial grade: 0°C to +70°C.
Industrial grade: -40°C to +85°C.
Module operating temperature range depends also on customer design and cooling solution. Please contact us for options.
Physical Dimensions
- Module size: 50 mm × 40 mm. Please download the assembly diagram for exact numbers.
- Mating height with standard connectors: 8mm
- PCB thickness: 1.6mm
- Highest part on PCB: approx. 2.5mm. Please download the step model for exact numbers.
All dimensions are shown in millimeters.
Figure 3: Physical Dimensions of the TE0711-01 board.
Weight
20.6 g | Plain module |
8.8 g | Set of bolts and nuts |
Table 11: Module weight data.
Revision History
Hardware Revision History
Date | Revision | Notes | PCN | Documentation Link |
---|---|---|---|---|
2015-01-02 | 01 | First production release Current Hardware Revision | TE0711 TRM |
Table 12: Hardware revisions.
Hardware revision number is printed on the PCB board together with the module model number separated by the dash.
Document Change History
Date | Revision | Contributors | Description |
---|---|---|---|
2017-01-01 | Ali Naseri, Thorsten Trenz, Jan Kumann | TRM revision. | |
2015-06-05 | 0.1 | Antti Lukats | Initial version. |
Disclaimer
Data Privacy
Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy
Document Warranty
The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.
Limitation of Liability
In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.
Copyright Notice
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.
Technology Licenses
The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.
Environmental Protection
To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.
REACH, RoHS and WEEE
REACH
Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).
RoHS
Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.
WEEE
Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.
Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.