| Company | Trenz Electronic GmbH |
|---|---|
| PCN Number | PCN-20240302 |
| Title | TE0725-03 to TE0725-04 Hardware Revision Change |
| Subject | Hardware Revision Change |
| Issue Date | 2024-03-01 |
Products Affected
This change affects all Trenz Electronic TE0725 SoMs: TE0725-03*.
Affected Product | Replacement |
|---|---|
| TE0725-03-15-1C | TE0725-04-21C-1-A |
| TE0725-03-35-2C | TE0725-04-42C-1-A |
| TE0725-03-100-2C | TE0725-04-72C-1-A |
| TE0725-03-100-2CF | TE0725-04-72C-1-F |
| TE0725-03-100-2I9 | TE0725-04-72I-1-B |
(ED: Tabelle ist fertig.)
Changes
#1 Changed DCDC EN5311QI (U11) to MPM3834C (U5) and adapted power circuit.
Type: Schematic Change
Reason: EOL of Component.
Impact: None. Increased current output capability. Minor changes in electrical characteristics.
#2 Changed DCDC EN6347QI (U10) to MPM3860GQW-Z and adapted power circuit.
Type: Schematic Change
Reason: EOL of Component.
Impact: None. Increased current output capability. Minor changes in electrical characteristics.
#1 Changed HyperRAM (U4) from S27KS0641DPBHI000 to ???.
Type: BOM change
Reason: HyperRAM improvement.
Impact: None. ???
#7 Added jumper (J3) option (default: not fitted) and resistor (R36) to enable JTAG only boot mode.
Type: Schematic Change
Reason: QSPI programming problems with newer Vivado versions.
Impact: None. JTAG boot mode directly accessible. Fix QSPI programming problems with newer Vivado versions according to AR#00002 - QSPI Programming issues.
#6 Added diode (D1) between signals "INIT" and "PROG_B".
Type: Schematic Change
Reason: Keep FPGA in reset while signal "PROG_B" is low during initial power-up.
Impact: None.
#5 Added diode (D4) between voltage monitor (U9) pin 3 net "nRST" and voltage rail 3.3V.
Type: Schematic Change
Reason: Protect manual reset pin.
Impact: None.
#1 Added pull-up resistor (R37) for signal "H1_A3".
Type: Schematic Change
Reason: Setup CS# signal externally.
Impact: None.
#1 Set resistor (R13) to not fitted.
Type: BOM Change
Reason: BOM Optimization.
Impact: None.
#19 Changed inductor (L1, L2, L3, L4, L6) from BKP0603HS121-T to MPZ0603S121HT000.
Type: BOM Change
Reason: EOL of component.
Impact: None.
#28 Added testpoint (TP1, ..., TP10).
Type: Schematic Change
Reason: Voltage and system monitoring improvement.
Impact: None.
#17 Removed track-it traceability pad S/N.
Type: Schematic Change
Reason: EOL of Component.
Impact: None.
#12 Changed fiducials to standard fiducial type.
Type: Schematic Change
Reason: Use standard fiducials.
Impact: None.
#30 Updated components from library.
Type: Schematic Change
Reason: Use latest component data.
Impact: None.
#33 Added legal notices, system and power overview. Updated revision history. Updated page count and order.
Type: Documentation Update
Reason: Documentation improvement.
Impact: None.
Method of Identification
The revision number is shown on the top side of the PCB. Revision number position changes between REV03 and REV04 on top side of the PCB.
Production Shipment Schedule
From October 2024, after old stock is gone. If the new revision is not suitable for your application and still the former revision of the board is needed, please contact us.
Contact Information
If you have any questions related to this PCN, please contact Trenz Electronics Technical Support at
- forum.trenz-electronic.de
- wiki.trenz-electronic.de
- support%trenz-electronic.de (subject = PCN-20240302)
phone
national calls: 05741 3200-0
international calls: 0049 5741 3200-0
Disclaimer
Any projected dates in this PCN are based on the most current product information at the time this PCN is being issued, but they may change due to unforeseen circumstances. For the latest schedule and any other information, please contact your local Trenz Electronic sales office, technical support or local distributor.
This PCN follows JEDEC Standard J-STD-046.
Overview
Content Tools