Download PDF version of this document.
Table of Contents
The Trenz Electronic TEMB0005 is an industrial-grade carrier for the module TEM00005. The carrier is equipped with a Gigabit LAN socket, a USB2.0 interface, two different Samtec B2B Connectors, three Tiger Claw Samtec Dual Sockets, a PMod Connector, a pin header and a FTDI. Find more information in the FTDI sections.
Refer to http://trenz.org/temb0005-info for the current online version of this manual and other available documentation.
Storage device name | Content | Notes |
---|---|---|
EEPROM | Programmed | FTDI Confirguration |
Signal | B2B | Connected to | Note |
---|---|---|---|
RESET | J11- 54 | B2B, J5 | General Reset |
M_RESET | J11- 11 | Push Button, S1 | Module Reset |
The carrier TEMB0005 is equipped with a Samtec Micro Blade B2B Connector. More information in the following table.
Designators | Interface | I/O Signal Count | Connected to | Notes |
---|---|---|---|---|
J11 | JTAG | 4x Single Ended | FTDI, U1 | |
GPIO | 24x Single Ended, 12x Differential Pairs | CRUVI B2B, J5 | A0...5, B0...5 (N/P) | |
GPIO | 8x Single Ended | CRUVI B2B, J6 | A_X0...7 | |
GPIO | 8x Single Ended | CRUVI B2B, J7 | B_X0...7 | |
GPIO | 8x Single Ended | CRUVI B2B, J8 | C_X0...7 | |
LEDs | 4x Single Ended | D1...4 | LED1...4 | |
I/O | 8x Single Ended | Pmod Header, J9 | ||
Push Buttons | 2x Single Ended | Push Button, S1-S2 | M_RESET, Button | |
I2C | 4x Single Ended | CRUVI B2B, J6-J5 | 2x I2C Channels | |
ETH | 4x Single Ended, 2x Differential Pairs 2x Single Ended | RJ45 Socket, J1A RJ45 LEDs, J1B-J1C | 2x LAne Transmit and Receive Yellow and Green LEDs | |
UART | 2x Single Ended | FTDI, U1 | UART RX/TX | |
FTDI I/O | 2x Single Ended | FTDI, U1 | BDBUS2-BDBUS3 | |
CLK | 1x Single Ended 1x Single Ended | Oscillator, U8 CRUVI B2B, J5 | 30 MHz Reference Clock | |
Reset | 1x Single Ended 1x Single Ended | CRUVI B2B, J5 Push Button, S1 | RESET M_RESET | |
MODE | 1x Single Ended | CRUVI B2B, J5 | ||
GPIO | 7x Single Ended | CRUVI B2B, J5 | ||
Power Signal | 1x Single Ended | RED LED, D8 |
The TEMB0005 is equipped with three Low Speed Connectors J6...8 and a High Speed Connector J5. These connectors are provided for CRUVI extension cards.
Speed | Designators | Schematic | Connected to | Notes |
---|---|---|---|---|
Low | J6 | A_X0...1 | B2B, J11 | GPIO |
A_X2...5 | B2B, J11 | SC SPI | ||
A_X6...7 | B2B, J11 | I2C0 SDA/SCL | ||
J7 | B_X0...7 | B2B, J11 | GPIO | |
J8 | C_X0...7 | B2B, J11 | GPIO | |
High | J5 | A0...A5 (N/P) | B2B, J11 | |
B0...B5 (N/P) | B2B, J11 | |||
MODE | B2B, J11 | |||
RESET | B2B, J11 | |||
SMB_ALERT SMB_SDA SMB_SCL | B2B, J11 | |||
DI,DO,SCK,SEL | B2B, J11 | SPI | ||
HSIO, HI, HO | B2B, J11 |
There is a USB2.0 Socket, J2 provided in order to communicate with the FTDI, U1. Data signals from USB2.0 are passed through a Line Filter L1 and a Diode U2 in order to be protected against inverse polarity connection.
Pin | Schematic | Connected to | Notes |
---|---|---|---|
ID | N.C | N.C | |
D+ | DL_P | FTDI, U1 | Through Line Filter, L1 |
D- | DL_N | FTDI, U1 | Through Line Filter, L1 |
Vbus | VBUS | Diode, U2 |
There is a RJ45 Ethernet LAN Socket, J1 connected to B2B, J11 via 2x channels data receive and transmit.
Pin | Schematic | Connected to | Notes |
---|---|---|---|
TD+ | ETH1_TX_P | B2B, J11 | |
TD- | ETH1_TX_N | B2B, J11 | |
RD+ | ETH1_RX_P | B2B, J11 | |
RD- | ETH1_RX_N | B2B, J11 | |
Green LED | ETH1_LED0 | B2B, J11 | Link/Activity indicator |
Yellow LED | ETH1_LED1 | B2B, J11 | Speed indicator |
There is a PMod Header, J9 connected to the B2B, J11 and all signals are protected from invers polarity by two diodes D6, D7.
Schematic | Connected to | Notes |
---|---|---|
PM0...3 (N/P) | B2B, J11 |
There is a Pin Header 6x1, J3 provided for SPI signals.
Pin | Schematic | Connected to | Notes |
---|---|---|---|
1 | 3.3V | B2B, J11 | |
2 | GND | B2B, J11 | |
3 | SC_SDO | B2B, J11 | |
4 | SC_SDI | B2B, J11 | |
5 | SC_SS | B2B, J11 | |
6 | SC_CLK | B2B, J11 |
There is an UART channel provided in order to communicate with the module and signals are accessible via B2B, J11 through the FTDI, U1.
U1 Pin | Schematic | Connected to | Notes |
---|---|---|---|
BDBUS1 | UART1_TXD | B2B, J11 | FTDI receiver input |
BDBUS0 | UART1_RXD | B2B, J11 | FTDI transmitter output |
JTAG access is provided through B2B connector J11 connected to the FTDI. For more information please refer to the FTDI section.
JTAG Signal | B2B Connector |
---|---|
TMS | J11-14 |
TDI | J11-8 |
TDO | J11-10 |
TCK | J11-12 |
JTAGSEL | J11-9 |
Test Point | Signal | Connected to | Notes |
---|---|---|---|
TP1 | GOLDEN | B2B, J11 | |
TP2 | JTAGSEL | B2B, J11 | |
TP3 | PG_DCDC | B2B, J11 | Red LED, D8 |
TP4 | VADJ | Regulator, U6 | |
TP5 | PROBE_B | B2B, J11 | |
TP6 | PROBE_A | B2B, J11 |
Chip/Interface | Designator | Notes |
---|---|---|
FTDI | U1 | |
LEDs | D1...D5 | |
Push Buttons | S1-S2 | |
EEPROM | U3 | |
Oscillator | U4-U8 |
The FTDI chip (U1) converts signals from USB2 to variety of standard serial and parallel interfaces. Refer to the FTDI data sheet to get information about the capacity of the FT2232H chip. FTDI FT2232H chip is used in Multi-Protocol Synchronous Serial Engine (MPPSE) mode for JTAG.
The configuration of FTDI FT2232H chip is pre-programmed on the EEPROM U6.
Pin | Schematic | Connected to | Notes |
---|---|---|---|
ADBUS0 | TCK | B2B, J10 | JTAG interface |
ADBUS1 | TDI | B2B, J10 | |
ADBUS2 | TDO | B2B, J10 | |
ADBUS3 | TMS | B2B, J10 | |
BDBUS0...7 | BDBUS0...7 | B2B, J10 | User IO |
OSCI | OSCI | Oscillator, U7 | Clock |
EECS | EECS | EEPROM, U6 | EEPROM Contains FTDI configuration |
EECLK | EECLK | B2B, J10 | |
EEDATA | EEDATA | B2B, J10 | |
DM/DP | USB_N/ USB_P | Micro USB, J8 | USB to UART |
nRESET | 3.3V | 3.3V |
There is an EEPROM IC, U3 provided for storing the FTDI (U1) configuration.
Pin | Schematic | Notes |
---|---|---|
DI/DO | EEDATA | |
CLK | EECLK | |
CS | EECS |
The EEPROM address is as the following.
I2C Address | Designator | Notes |
---|---|---|
0x70 | U3 |
Designator | Schematic | Connected to | Functionality | Note |
---|---|---|---|---|
S1 | M_RESET | B2B, J11 | Reset | User LEDS |
S2 | Button | BUTTON | User Button | Power Status LED |
Designator | Color | Connected to | Active Level | Note |
---|---|---|---|---|
D1...D4 | Green | B2B, J11 | Active High | User LEDS |
D5 | Green | 5VIN | Active High | Power Status LED |
D6 | Red | PG_DCDC | Active Low |
Designator | Description | Frequency | Note |
---|---|---|---|
U4 | MEMS Oscillator | 12 MHz | |
U8 | MEMS Oscillator | 30 MHz |
Power supply with minimum current capability of 2 A for system startup is recommended.
Power Input Pin | Typical Current |
---|---|
5VIN | TBD* |
* TBD - To Be Determined
Power Rail Name | B2B Connector J11 Pin | CRUVI Connector J6 Pin | B2B Connector J7 Pin | B2B Connector J8 Pin | Direction | Notes |
---|---|---|---|---|---|---|
3.3V | 1, 2, 3, 4 | 10 | 10 | 10 | ||
5VIN | - | 12 | 12 | 12 |
CRUVI carrier use on top side:
Mating height of the high speed connectors is 5mm. The low speed connectors mate correctly within a range from 4.78 mm to 5.29 mm.
Current rating of High Speed B2B connectors is 1.6A per pin (2 pins powered).
Current rating of Low Speed B2B connectors is 4.1A per pin (2 pins powered).
There is no data available for the connectors actual used here. Data available for other stacking heights of same connectors is summarized in the folllowing table:
Connector | Speed ratings |
---|---|
ST4/SS4 single ended (4mm stacking height!) | 13.5GHz / 27 Gbps |
ST4/SS4 differential (4mm stacking height!) | 15.5 GHz / 31 Gbps |
TMMH/CLT single ended (4.77mm stacking height!) | 5.5GHz / 11 Gbps |
All connectors are specified for a temp. range of -55 °C to 125 °C.
Symbols | Description | Min | Max | Unit |
---|---|---|---|---|
VIN | Input Supply Voltage | -5 | +5 | V |
T_STG | Storage Temperature | -55 | 125 | °C |
Operating temperature range depends also on customer design and cooling solution. Please contact us for options.
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
VIN | 4.06 | 5.58 | V | See the carrier datasheets. |
T_OPT | -45 | 85 | °C |
Module size: 115 mm × 70 mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: 4 mm.
PCB thickness: 1.7 mm.
Trenz shop TEMB0005 overview page | |
---|---|
English page | German page |
Date | Revision | Changes | Documentation Link |
---|---|---|---|
2020-05-20 | REV01 | Initial Release | --- |
Hardware revision number can be found on the PCB board together with the module model number separated by the dash.
Date | Revision | Contributor | Description |
---|---|---|---|
| |||
-- | all |
|
Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy
The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.
In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.
The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.
To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.
REACH
Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).
RoHS
Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.
WEEE
Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.
Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.