You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 8 Next »

Table of contents

Overview

CPLD Device: LCMX02-1200HC

Feature Summary

Firmware Revision and supported PCB Revision

See Document Change History

Product Specification

Port Description

NameDirectionPinDescription
ACBUS4                96FTDI / currently_not_used
ACBUS5                88FTDI / currently_not_used
ADBUS4               out98constant 0 / currently_not_used
ADBUS7               in97/ currently_not_used
BDBUS0               in87UART TX from FTDI
BDBUS1               out86UART RX to FTDI
C_TCKout81JTAG FTDI
C_TDIout84JTAG FTDI
C_TDOin83JTAG FTDI
C_TMSout85JTAG FTDI
CM0                  in99DIP Switch S3-M1
CM1                  in1DIP Switch S3-M2
EN_FMC               out31VADJ and 3V3V_FMC Power on
EN1                  out24Power Enable Pin for Module CPLD
FMC_PRSNT            in28FMC Card present pin (zero if not present)
FMC_SCL              out10FMC I2C
FMC_SDAinout8FMC I2C
FMC_TCK               4JTAG FMC / currently_not_used
FMC_TDI               12JTAG FMC / currently_not_used
FMC_TDO               9JTAG FMC / currently_not_used
FMC_TMS               7JTAG FMC / currently_not_used
HDMI_SCL             inout47HDMI
HDMI_SDA             inout45HDMI
HDMI_SPDIF            15HDMI / currently_not_used
HDMI_SPDIFOUT         14HDMI / currently_not_used
JTAGEN               --82

Enable JTAG access to carrier CPLD for Firmware update (zero: JTAG routed to module, one: CPLD access)

Set DIP Switch S3-JTAGEN to ON, for module access.

M_TCK                in91JTAG Module
M_TDI                in94JTAG Module
M_TDO                out95JTAG Module
M_TMS                in90JTAG Module
MIO10                inout29MIO
MIO11                inout19MIO
MIO12                inout36MIO
MIO13                inout30MIO
MIO14                inout37 MIO / Module UART0.RX << BDBUS0
MIO15                in18 MIO / Module UART0.TX >> BDBUS1
MODE                 out27Boot Mode for Zynq Devices (Flash or SD)
NOSEQ                inout21 
PG_C2M               out20 
PGOOD                inout25 
PHY_LED1             out42 
PHY_LED2             out43 
POK_FMC              in32FMC Power good from FMC VADJ DCDC
PX6                  inout49 
PX7                  inout48 
RESIN                out13 
S1                   in3User Pushbutton
S2                   in2User Pushbutton / global Reset
SD_DETECT            in40SD Detection
SD_WP                in41SD
SEL_SD               out39SD Selection, MMC SD Slot or PMOD J2
ULED1                out78LED D1
ULED2                out77LED D2
ULED3                out76LED D3
ULED4                out16LED D4
ULED5                out69LED D5, powered by FMC VADJ
ULED6                out68LED D6, powered by FMC VADJ
ULED7                out65LED D7, powered by FMC VADJ
ULED8                out64LED D8, powered by FMC VADJ
USB_OC               in17USB Over Current
VID0                 out34VADJ Voltage selection (EN5335QI)
VID1                 out35VADJ Voltage selection (EN5335QI)
VID2                 out38VADJ Voltage selection (EN5335QI)
X6                   in60 
Y0                   in75I2C SCL
Y1                   out66I2C SDA_OUT
Y2                   in67RGPIO CLK
Y3                   out70RGPIO TX
Y4                   in74RGPIO RX
Y5                   in71I2C SDA_IN
Y6                   in63 

 

Functional Description

JTAG

Power

...

Appx. A: Change History and Legal Notices

Revision Changes

Document Change History

To get content of older revision  got to "Change History"  of this page and select older document revision number.

DateDocument RevisionCPLD Firmware RevisionSupported PCB RevisionAuthorsDescription

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]


 

REV05REV03,REV04,REV05

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]


Work in progress
2016-04-11

v.1

--- 

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]


Initial release
 All  
 

Legal Notices

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

 

  • No labels