Introduction

This User Manual describes the Electronic Drive Development Platform (EDDP) main concepts.

Requirements

• Xilinx SDSoC 2017.1 for SDSoC Design Flow or
• Xilinx Vivado 2017.1 for HLS Design Flow
• PC that satisfies the host workstation requirements for Xilinx Tools
• Controller Board (Default: Digilent ARTY-Z 7010)
  • Micro-USB Cable (not included in the EDDP kit)
  • RJ45 ethernet Cable (not included in the EDDP kit)
  • 12V Wall supply for Controller board (included in EDDP kit)
  • microSD Card (included in the EDDP kit)
• EDPS Drive Board TEC0053 (Default: 2 phase measurement, max 25A)
  • EDPS Motor Adapter Board TEC0060 with default Motor/Encoder installed and 12V Wall supply or
  • Custom Motor and Encoder with cables and DC Link power source
• Experience with Xilinx SDSoC and/or Xilinx Vivado. Pre-requisites: basic knowledge of Xilinx All Programmable FPGA and/or SoC devices, basic knowledge of Xilinx SDK and C/C++ programming

Installation

bla

Control Board

Digilent ARTY-Z 7010 is considerd as primary and default Control Board for EDDP as it is delivered as part of the EDDP Kit.

EDPS Drive Board TEC0053

Option 1: with DC +12V Reference Motor Board (Delivery condition)

Option 2: Customer Motor at individual DC +5..48V

Block Diagram

Main Components

• MOSFET drivers for 3-phase BLDC Motors
• Current measurement for 2-phases (3 phase measurement optional)
• Temperature sensor on board and 1-Wire bus external option
• Encoder input (differential or single ended signals)

Key Features

• Motor Evaluation with a FPGA controller board, recommended with the Digilent Arty Z7 board
• Quick evaluation with reference motor board
• Power option up to 48V and 30A main supply current  

Scope of delivery

• This Eval Board comes with the already mounted and wired "Reference Motor Board"
• One "Arty Z7" Board: http://store.digilentinc.com/arty-z7-apsoc-zynq-7000-development-board-for-makers-and-hobbyists/usable with the reference FPGA IPs: TODO insert link
• Any DC +12V must be supplied to both boards supply connectors
  (Two AC/DC Wall Mount Adapters are delivered as optional DC +12V power source)
• One FUSE F1 30A for motor supply option 2

General Safety Instructions

• This product is only allowed to be used by an electrical specialist.
• This product is not allowed to be used unattended.
• There is a possible risk of burns due to hot surfaces while running the Board. This e.g. might be caused by an overcurrent at the motor outputs.
• All externally connected power sources must be SELV protected (Separated or safety extra-low voltage).
  
• For set up the wiring switch off or disconnect all external power supplies.
• During operations it is not allowed to change the wiring or mechanical setup.
• This product is only allowed to be used in dry an indoor environment.
• The product is only allowed to be used in horizontal position on a non-conducting and non-inflammable surface.
• The mechanical setup must ensure that the whole test setup can not be dropped to the floor or moved accidently.
  
  
  

Signals, Interfaces and Pins

Controller Board Connections (Arty etc.)

Motor and Power Concept

There are two options available for the motor and power concept:

Detail	Option 1: Reference Motor Board with DC +12V Supply	Option 2: Customer Motor at individual DC +5..48V	Comment
Motor Supply	From DC +12V Input J7 via Fuse F3 (TODO ... A) via Motor Reference Board to J5 of Eval board	From customer DC Supply to J6 via F1 on Eval Boad
Motor Connection	Motor wires connected to cage clamps on Motor Reference Board J5 (A), J4 (B), J3 (C)	Motor wires connected to bolt screw terminals on Eval Board J2 (A), J3 (B), J4 (C)
Encoder Connection	From encoder pins via ribbon cable to Eval Board J10, (only for single ended enconders optimized for Reference Motor Board) J11 single ended: Pin 1: GND Pin 2: ENC I input Pin 3: ENC A input Pin 4: +5V Supply Pin 5: ENC B input Pin 6: GND	From motor to Eval Board J10 (only single ende signals) see left colomn, or to J11 (single OR differential signals): J11 single ended: Pin 1: not connected Pin 2: +5V Supply Pin 3: GND Pin 4: not connected Pin 5: unused (100R to ENC A input) Pin 6: ENC A input Pin 7: unused (100R to ENC B input) Pin 8: ENC B input Pin 9: unused (100R to ENC I input) Pin 10: ENC I input J11 differential with 100R terminated: Pin 1: not connected Pin 2: +5V Supply Pin 3: GND Pin 4: not connected Pin 5: ENC A negativ Pin 6: ENC A positiv Pin 7: ENC B negativ Pin 8: ENC B positiv Pin 9: ENC I negativ Pin 10: ENC I positiv	Jumper Settings for encoder signals. Single Ended:           Differential:

Reference Motor Board TEC0060

Reference Motor

The manufaturer of the reference motor is Anaheim Automation and the order code of the delivered combination of the motor with encoder is BLWR111D-24V-10000-1000SI. Please not the encoder is not available separatly, they are premounted to the motor at the manufacturer.
The nominal motor voltage is DC 24V which is supplied by DC 12V on the Reference Motor Board. This will cause a certain derating in performace.

The datasheet for the motor:
http://www.anaheimautomation.com/manuals/brushless/L010234%20-%20BLWR11%20Series%20Product%20Sheet.pdf

The datasheet for the encoder:
http://www.anaheimautomation.com/manuals/accessories/L010390%20-%20Single%20Ended%20Encoder%20with%20Index%20Channel.pdf

Internal

Temperature Sensor

Onboard is a Maxim 1-Wire Temperature sensor DS18S20Z+. This sensor is located at the middle of the PCB.
Addional 1-Wire temperature sensor(s) can be connected by wires to connector J16:

• Pin 1(DQ), 3 (GND),5 (+3.3V) at the same 1-wire bus as the onboard one
• Pin 2(DQ), 4 (GND),6 (+3.3V) at a separate 1-wire bus

Power and Power-On Sequence

Power Supply

DC 12V Supply Motor and Driver

This externally power supply sources must be SELV protected (Separated or safety extra-low voltage).

The motor drivers and the reference motor on the pre-mounted motor board TEC0060 are supplied by this voltage.

The internal +5V digital supply is generated out of this +12V supply.

DC 5...48V Supply for Motor only

SAFETY INSTRUCTIONS:

Externally power supply for the motor must be SELV protected (Separated or safety extra-low voltage).

This option is

• only allowed to be used for electrical specialist for the used electrical voltage and power conditions
• only allowed to be used under electrical laboratory conditions
• only allowed to be used in horizontal position on a non-conducting and non-inflammable surface
• only allowed to be used with a wiring, which fulfills the current rating for the maximum possible currents.
• only allowed to be used with a suitable current limiting circuit
  • The maximum continuous current must not exceed 30A.
  • The delivered fuse "Littelfuse Tpye 142.5631.5302" must be used as current limiter between connector J5 and J6.
  • To limit the current for smaller motor loads an ADDITIONALLY appropriate current limiter can be used e.g. a current limited power source or a fuse integrated in the wiring.
    
• only allowed to be used with appropriate connectors at the M5 screw connectors, which means M5 cable lugs must be used and fastened according to technical standards.
  
• only allowed to be used, if the "Eval Boad high current signals" conducting up to 30A nominal, are covered by isolating, mechanically stable, non-inflammable (UL V-1 or better) material
  

  • The "Eval Boad high current signals" are the motor outputs A, B, C and Fuse F1 Connectors J5 an J6 and further internal connections shown white marked in the following picture:
    
    

  • As minimum protection it is mandatory to use the delivered "Isolating cover PCB" (marked in green), which must be mounted to the mounting holes H1, H9, H3, H4 with the delivered 10mm isolating spacers:
    
    
    
  • The used cable lugs need to be isolated in the area outstanding the outer border of the Eval Board.
    Intention is to make sure that the "Isolating Cover PCB" is overlapping the conducting material by a minimum of 2 cm.

Initial operation

The option 2 motor supply is only usable after the following steps are done:

1. Disconnecting the reference motor board TEC0060 by unmounting its screws and the encoder cable from J10
2. Mounting the delivered 30A Fuse to the connectors J5 and J6 with the delivered M5 screws
   1. For lower supply current requirements, caused by the power rating of the used motor, a fuse with a lower and suitable current rating integrated in the supply wiring is recommended.
3. Connecting with a cable lugs the +DC 5..48V to J6 and the corresponding GND to J1.
   1. The cable length is limited to 3m.
4. Connection the three motor phases to J2 (A), J3 (B) and J4 (C).
   1. The cable length is limited to 3m.
5. Optional: connect the encoder wires to J10 or J11
   and set jumper field according to signal specification: differential or single ended
   See section TODO for details

Power Consumption

Power-On Sequence

Any power sequence of the three supply sources is allowed:

• +3V3 Supply from the FPGA Board, generated by FPGA Board supply
• +12V and
• optional +5..48V Motor Supply

Variants Currently In Production

TODO:

Technical Specifications

Absolute Maximum Ratings

Recommended Operating Conditions

Physical Dimensions

• Board size: 100 mm × 166 mm.  Please download the assembly diagram for exact numbers.

• PCB thickness: 1.75 mm +/-10%

• Highest part on PCB: approximately 17 mm. Please download the step model for exact numbers.

All dimensions are shown in mm. Additional sketches, drawings and schematics can be found TODO: here.

Operating Temperature Ranges

Weight

Revision History

Hardware Revision History

Hardware revision number is printed on the PCB board in the down right corner.

Document Change History

Disclaimer

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.