You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 5 Next »

 

Key Features

  • Motor evaluation with an FPGA controller board, recommended with the Digilent Arty Z7 board
  • Quick evaluation with reference motor board
  • Power option up to 48V and 30A main supply current

 

Block Diagram

Main Components

  • MOSFET drivers for 3-phase BLDC Motors
  • Current measurement for 2-phases (3 phase measurement optional)
  • Temperature sensor on board and 1-Wire bus external option
  • Encoder input capable of receiving both single ended and differential signals

Scope of Delivery

General Safety Instructions

  • This product is only allowed to be used by an electrical specialist.
  • This product is not allowed to be used unattended.
  • There is a possible risk of burns due to hot surfaces while running the Board. This e.g. might be caused by an overcurrent at the motor outputs.
  • All externally connected power sources must be SELV protected (Separated or safety extra-low voltage).
  • For set up the wiring switch off or disconnect all external power supplies.
  • During operations it is not allowed to change the wiring or mechanical setup.
  • This product is only allowed to be used in a dry indoor environment.
  • The product is only allowed to be used in horizontal position on a non-conducting and non-inflammable surface.
  • The mechanical setup must ensure that the whole test setup can not be dropped to the floor or moved accidentally.


 

Signals, Interfaces and Pins

Control Board Connections

Signal namesConnector J8Connector J9Connector J17

Digital Supply to EDPS

Pin 6, 12: +3.3V
Pin 5, 11: GND

Pin 6, 12: +3.3V
Pin 5, 11: GND
Pin 5, 6, 21, 22: +3.3V
Pin 1, 2, 25, 26: GND

Motor Driver PWM Signals to EDPS

High and Low Side control signals
are
hardware protected against
simultaniously
ON switching
of the MOSFETs

 

Pin 1: G1H - Ch.A HighSide
Pin 7: G1L - Ch.A LowSide
Pin 2: G2H - Ch.B HighSide
Pin 8: G2L - Ch.B LowSide
Pin 3: G3H - Ch.C HighSide
Pin 9: G3L - Ch.C LowSide

 

Pin 11: G1H - Ch.A HighSide
Pin 12: G1L - Ch.A LowSide
Pin 9: G2H - Ch.B HighSide
Pin 10: G2L - Ch.B LowSide
Pin 7: G3H - Ch.C HighSide
Pin 8: G3L - Ch.C LowSide

ADC Clock Signal to EDPS Pin 1: SCLKPin 23: SCLK
Encoder Digital Signals from EDPS 

Pin 8: ENC_A
Pin 9: ENC_B
Pin 10: ENC_I

Pin 20: ENC_A
Pin 18: ENC_B
Pin 16: ENC_I

Motor Current ADC "raw" Signals from EDPS
(usable with FPGA IP)
 

Pin 2: SDI1 - Current Ch.A
Pin 3: SDI2 - Current Ch.B
Pin 4: SDI3 - Current Ch.C

Pin 19: SDI1 - Current Ch.A
Pin 17: SDI2 - Current Ch.B
Pin 15: SDI3 - Current Ch.C

Supply Voltage ADC "raw" Signal from EDPS
(usable with FPGA IP)
 

Pin 7: SDIV - from DC_LINK
(Fused Motor Supply Voltage)

Pin 24: SDIV - from DC_LINK
(Fused Motor Supply Voltage)

1-Wire bus for temperature measurementPin 10: EXT1 - 1-Wire Bus 1
Pin 4: EXT2 - 1-Wire Bus 2
 

Pin 4: EXT1 - 1-Wire Bus 1
Pin 3: EXT2 - 1-Wire Bus 2

Not connected pinsnonenonePin 13, 14

Motor and Power Connections

There are two options available for the motor and power concept:

DetailOption 1: Reference Motor Board with DC +12V SupplyOption 2: Customer Motor at individual DC +5..48VComments
Motor Supply

From DC +12V Input J7 via Fuse F3 (TODO ... A)
via Motor Reference Board to J5 of Eval board

From customer DC Supply to J6 via F1 on Eval Boad 
Motor ConnectionMotor wires connected to cage clamps on
Motor Reference Board J5 (A), J4 (B), J3 (C)
Motor wires connected to bolt screw terminals on
Eval Board J2 (A), J3 (B), J4 (C)
 
Encoder Connection

From encoder pins via ribbon cable to Eval Board J10,
(only for single ended enconders optimized for
Reference Motor Board)

J11 single ended:
Pin 1: GND
Pin 2: ENC I input
Pin 3: ENC A input
Pin 4: +5V Supply
Pin 5: ENC B input
Pin 6: GND

From motor to Eval Board J10 (only single ende signals) see left colomn, or to J11 (single OR differential signals):

J11 single ended:
Pin 1: not connected
Pin 2: +5V Supply
Pin 3: GND
Pin 4: not connected
Pin 5: unused (100R to ENC A input)
Pin 6: ENC A input
Pin 7: unused (100R to ENC B input)
Pin 8: ENC B input
Pin 9: unused (100R to ENC I input)
Pin 10: ENC I input

J11 differential with 100R terminated:
Pin 1: not connected
Pin 2: +5V Supply
Pin 3: GND
Pin 4: not connected
Pin 5: ENC A negativ
Pin 6: ENC A positiv
Pin 7: ENC B negativ
Pin 8: ENC B positiv
Pin 9: ENC I negativ
Pin 10: ENC I positiv

Jumper Settings for encoder signals.



Single Ended:           Differential:
   

 

 

Internal

Temperature Sensor

Onboard is a Maxim 1-Wire Temperature sensor DS18S20Z+. This sensor is located in the middle of the PCB.
Addional 1-Wire temperature sensor(s) can be connected to the connector J16:

 

  • Pin 1(DQ), 3 (GND),5 (+3.3V) at the same 1-wire bus as the onboard one
  • Pin 2(DQ), 4 (GND),6 (+3.3V) at a separate 1-wire bus

Power and Power-On Sequence

Power Supply

DC 12V Supply Motor and Driver

The power source must be SELV (Separated or safety extra-low voltageprotected.

The motor drivers and the reference motor on the pre-mounted motor board TEC0060 are supplied by this voltage.

The internal +5V digital supply is generated from this +12V supply.

DC 5...48V Supply for Motor only

SAFETY INSTRUCTIONS:

Externally power supply for the motor must be SELV (Separated or safety extra-low voltageprotected.

This option is

  • only allowed to be used for electrical specialist for the used electrical voltage and power conditions
  • only allowed to be used under electrical laboratory conditions
  • only allowed to be used in horizontal position on a non-conducting and non-inflammable surface
  • only allowed to be used with a wiring, which fulfills the current rating for the maximum possible currents.
  • only allowed to be used with a suitable current limiting circuit
    • The maximum continuous current must not exceed 30A.
    • The delivered fuse "Littelfuse Tpye 142.5631.5302" must be used as current limiter between connector J5 and J6.
    • To limit the current for smaller motor loads an ADDITIONALLY appropriate current limiter can be used e.g. a current limited power source or a fuse integrated in the wiring.
  • only allowed to be used with appropriate connectors at the M5 screw connectors, which means M5 cable lugs must be used and fastened according to technical standards.
  • only allowed to be used, if the "Eval Boad high current signals" conducting up to 30A nominal, are covered by isolating, mechanically stable, non-inflammable (UL V-1 or better) material
    • The "Eval Boad high current signals" are the motor outputs A, B, C and Fuse F1 Connectors J5 an J6 and further internal connections shown white marked in the following picture:

    • As minimum protection it is mandatory to use the delivered "Isolating cover PCB" (marked in green), which must be mounted to the mounting holes H1, H9, H3, H4 with the delivered 10mm isolating spacers:


    • The used cable lugs need to be isolated in the area outstanding the outer border of the Eval Board
      Make sure that the "Isolating Cover PCB" is overlapping the conducting material by a minimum of 20 mm.

Initial operation

To use a separate power supply for the motor supply perform the following steps:

  1. Disconnect the reference motor board TEC0060 by unmounting its screws and the encoder cable from J10
  2. Mount the delivered 30A fuse to the connectors J5 and J6 with the delivered M5 screws
    1. For lower supply current requirements, caused by the power rating of the used motor, a fuse with a lower and suitable current rating integrated in the supply wiring is recommended.
  3. Connect with cable lugs the +DC 5..48V to J6 and the corresponding GND to J1.
    1. The cable length is limited to 3m.
  4. Connect the three motor phases to J2 (A), J3 (B) and J4 (C).
    1. The cable length is limited to 3m.
  5. Optional: connect the encoder to J10 or J11 and set jumper field according to signal specification: differential or single ended. See section TODO for details.

Power Consumption

Test Condition:

  • 25 °C ambient
  • Reference motor running with no load
VIN Current mANotes
TEC0053-03 +3V3TODO mA 
TEC0053-03 +12VTODO mA 

Power-On Sequence

Any power sequence of the three supply sources is allowed:

  • +3V3 Supply from the FPGA Board, generated by FPGA Board supply
  • +12V and
  • optional +5..48V Motor Supply

Reference Motor Board TEC0060

For easy connection of the reference Motor and Encoder to the Driver board a special Motor Adapter Board TEC0060 is included in the EDDP Kit.

Reference Motor

The reference motor is manufactured by Anaheim Automation. The order code for the motor with the encoder already mounted is BLWR111D-24V-10000-1000SI. Please note that the encoder is not available separately. The nominal motor voltage is DC 24V, however, only 12V is supplied by the Reference Motor Board, which results in reduced performance.

The datasheet for the motor can be found at
http://www.anaheimautomation.com/manuals/brushless/L010234%20-%20BLWR11%20Series%20Product%20Sheet.pdf

The datasheet for the encoder can be found at
http://www.anaheimautomation.com/manuals/accessories/L010390%20-%20Single%20Ended%20Encoder%20with%20Index%20Channel.pdf

 

WIP section

 

 

 

Technical Specifications

Absolute Maximum Ratings

ParameterMinMax

Units

Notes

Reference document

DC +12V supply

038

V

 LM20242 datasheet
DC +5..48V supply080VV IPB015N08N5 datasheet
DC +3V3 supply-0.56V DS18S20Z datasheet
PWM Input-0.56.5V SN74LVC1G97 datasheet
ADC Digital Input-0.53.8VDC +3V3 = 3.3VAD7403 datasheet
Encoder Input-712V SN65LBC173AD datasheet

 

Recommended Operating Conditions - TODO

ParameterMinMax

Units

Notes

Reference document

DC +12V supply

11.512.5

V

  
DC +5..48V supply548V  
DC +3V3 supply3.03.3V DS18S20Z datasheet
PWM Input0DC +3V3 supplyV  
ADC Digital Input0DC +3V3 supplyV  
Encoder Input-712V SN65LBC173AD datasheet

 

Electrical characteristics

DC +3V3 supply = 3.3V

ParameterMinMax

Units

NotesReference document
PWM Input Logic High Level2.2 V SN74LVC1G97 datasheet
PWM Input Logic Low Level 0.8V SN74LVC1G97 datasheet
ADC Digital Input Logic High Level2.7 V AD7403 datasheet
ADC Digital Input Logic Low Level 0.6V AD7403 datasheet
ADC Digital Output Logic High Level3.23.3VIo=-200μAAD7403 datasheet
ADC Digital Output Logic Low Level00.4VIo=+200μAAD7403 datasheet
Encoder Input Logic High Level (Differential) -0.2V SN65LBC173AD datasheet
Encoder Input Logic Low Level (Differential)-0.01 V SN65LBC173AD datasheet
Encoder Input Logic High Level (Single Ended)2 V SN65LBC173AD datasheet
Encoder Input Logic Low Level (Single Ended) 0.6V SN65LBC173AD datasheet

 

 

Physical Dimensions

  • Board size: 100 mm × 166 mm.  Please download the assembly diagram for exact numbers.

  • PCB thickness: 1.75 mm +/-10%

  • Highest part on PCB: approximately 17 mm. Please download the step model for exact numbers.

All dimensions are shown in mm. Additional sketches, drawings and schematics can be found TODO: here.

Operating Temperature Ranges - TODO

 

Weight - TODO

VariantWeight in gNote
-TODO

 


Revision History

Hardware Revision History - TODO

DateRevision

Notes

PCN LinkDocumentation Link
2016-03-2702  TEC0053-02
2017-08-1404   

Hardware revision number is printed on the PCB board in the down right corner.

Document Change History - TODO

Date

Revision

Authors

Description

2017-03-30

 

Andreas HeidemannInitial Version
  • No labels