You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 66 Next »

Table of content

Legend

  • (warning) : Attention: Carrier/Module combination only with special condition or PCB modification possible
  • (tick): Supported
  • (star): Supported with limitations
  • (error): Not Supported
  • (question): Table currently not complete, see TRM of module and carrier

TE0701


FMC(1)FMC VadjPMODSETHHDMICL Connector(5)SD CardUSB HostVBATT
TE0710(star)(question)(question)(question)(error), N.C.(error), N.C.(error), 3.3V B16 I/O(error)(error)
TE0711(star)(question)(question)(error)(tick)(question)(star),1.8V B16 I/O(error)(error)
TE0712(star)(question)(question)(star),100 MBit*(tick)(star),MGT's(star),1.8V B13 I/O(error)(error)
TE0713(star)(question)(question)(error)(error)(star),MGT's(star),1.8V B13 I/O(error)(error)
TE0715-15(star)(tick)(question)(tick)(tick)(star),MGT's(tick)(tick)(star), RTC and Key RAM
TE0715-30 (warning)(2)(star)(star),Max 1.8V(question)(tick)(tick)(star),MGT's(tick)(tick)(star), RTC and Key RAM
TE0720(star)(tick)(tick)(tick)(tick)(tick),LVDS(tick)(tick)(star), RTC and Key RAM
TE0741 (warning)(4)(star)(question)(question)(error)(tick)(star),MGT's(error),MGT's(error)(error)
TE0820 (warning)(2)(star)(star),Max 1.8V(question)(tick)(tick)(star),MGT's(star)(6)(tick)(star), PSBATT(7)
TE0841 (warning)(2)(3)(star)(question)(question)(error)(tick)(star),MGT's(error),MGT's(error)(star), Key RAM
  • (1) FMC is a LPC Connector (no gigabit transceivers) on TE0701: I2C and JTAG access over CPLD.
         Separate TE0701_FMC_PINOUT table (PDF/XLSX) is available on: Trenz_Electronic Download-Pinout
  • (2) HP IO Banks only support 1.8V
  • (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
  • (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
  • (5) CL Connector is usable as Cameralink only with module that map LVDS pins to this connector
  • (6) Works, but without carrier board modification out of specification: TE0701 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
  • (7) PS battery operated voltage (1.2V–1.5V).

TE0703


ETHSD CardUSB HostResetUser LEDsUSB UARTUSB JTAG
TE0710(question)(star), 3.3V B16 I/O(error)(tick)(star), 2 LEDs(tick)(tick)
TE0711(error)(star), 1.8V B16 I/O(error)(tick)(question)(tick)(tick)
TE0712(star), 100 MBit(star), 1.8V B13 I/O(error)(tick)(question)(tick)(tick)
TE0713(error)(star), 1.8V B13 I/O(error)(tick)(question)(tick)(tick)
TE0715-15(tick)(tick)(tick)(tick)(question)(tick)(tick)
TE0715-30 (warning)(2)(tick)(tick)(tick)(tick)(question)(tick)(tick)
TE0720(tick)(tick)(tick)(tick)(question)(tick)(tick)
TE0741 (warning)(4)(error)(error), MGTs(error)(tick)(question)(tick)(tick)
TE0820 (warning)(2)(tick)(tick)(6)(tick)(question)(question)(tick)(tick)
TE0841 (warning)(2)(3)(error)(error), MGTs(error)(tick)(question)(tick)(tick)
  • (2) HP IO Banks only support 1.8V
  • (3) MGT's Lanes connected to SD-Level shifter: TE0703-06: Leave J11 open; TE0703-05 and before: It's recommended to desolder level shifter.
  • (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
  • (6) REV06 select correct SDIO voltage by jumper J11. REV05 and before: Works, but without carrier board modification out of specification (TE0703 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V).

TE0705


PMODSETHSD CardUSB Host
TE0710(question)(question)(error), 3.3V B16 I/O(error)
TE0711(question)(error)(star),1.8V B16 I/O(error)
TE0712(question)100 MBit(star),1.8V B13 I/O(error)
TE0713(question)(error)(question)(error)
TE0715-15(question)(tick)(tick)(tick)
TE0715-30 (warning)(2)(question)(tick)(tick)(tick)
TE0720(tick)(tick)(tick)(tick)
TE0741 (warning)(4)(question)(error)(error),MGT's(error)
TE0820 (warning)(2)(question)(tick)(star)(6)(tick)
TE0841 (warning)(2)(3)(question)(error)(error),MGT's(error)
  • (2) HP IO Banks only support 1.8V
  • (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
  • (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
  • (6) Works, but without carrier board modification out of specification: TE0705 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.

TE0706


ETH1ETH2SD CardUSB Host
TE0710(question)(question)(star), 3.3V B16 I/O(error)
TE0711(error)(question)(star), 1.8V B16 I/O(error)
TE0712100 MBit(question)(star), 1.8V B13 I/O(error)
TE0713(error)(question)(question)(error)
TE0715-15(tick)(tick)(tick)(tick)
TE0715-30 (warning)(2)(tick)(tick)(tick)(tick)
TE0720(tick)(tick)(tick)(tick)
TE0741 (warning)(4)(error)(question)(error), MGTs(error)
TE0820 (warning)(2)(tick)(question)(tick)(6)(tick)
TE0841 (warning)(2)(3)(error)(question)(error), MGTs(error)
  • (2) HP IO Banks only support 1.8V
  • (3) MGT's Lanes connected to SD-Level shifter: TE0703-06: Leave J11 open; TE0703-05 and before: It's recommended to desolder level shifter.
  • (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
  • (6) REV03 select correct SDIO voltage by jumper. REV02 and before: Works, but without carrier board modification out of specification (TE0703 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V).

TEBA0841


SFPUSB HostSD Card
"J4 2x5 Pin Header(2.54)"

GPIO
"J20/J10 each 2x25 Pin Header(2.54)"


XMOD (JTAG/UART)

"JX1 2x6 Pin Header (2.54)"

GPIO

(JTAG/UART/MGT REFCLK)

"J3 2x8 Pin Header(2.54)"

TE0710(error)(error)(star),3.3V B16 I/O(star)(9)(tick)(star)(8)
TE0711(error)(error)(star),1.8V B16 I/O(star)(9)(tick)(tick), B34 CLK input
TE0712(tick)(error)(star),  B13 I/O(star)(9)(tick)(tick), B34 CLK input
TE0713(tick)(error)(star),  B13 I/O(star)(9)(tick)(tick)
TE0715 (warning)(10)(tick)(tick)(star)(7)(star)(9)(tick)(tick)
TE0715-30 (warning)(10)(tick)(tick)(star)(7)(star)(9)(tick)(tick)

TE0720 (warning)(10)

(error)(tick)(star)(7)(star)(9)(tick)(tick), B34 CLK input

TE0741 (11)

(tick)(error)(error),MGT's(star)(9)(tick)(tick)
TE0820 (warning)(10)(tick)(tick)(star)(6)(star)(9)(tick)(tick)
TE0841(tick)(error)(error),MGT's(star)(9)(tick)(tick)
  • TEBA0841 has no dedicated power plug connector for 3.3V main power. External Power Supply must be connected to  J17, J20, J4 or J3 3.3V Pin. Do not use XMOD for power supply.
  • TEBA0841-REV01 VCCIOB and VCCIOC are not connected.
  • (6) Works, but without carrier board modification out of specification: TE0706 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
  • (7) SD signals only, no SD-Card connector
  • (8) CLK not connected on TE0710
  • (9) Check schematics  or TE Master Pinout Excel Sheet for detailed connection and IO Bank power supply
  • (10) With TEBA0841-01 is Boot Mode not selectable, please contact Trenz Electronic Support, if you need a Zynq or ZynqMP Module with TEBA0841-1. With TEBA0841-2 it's usable.
  • (11) MGT polarity is swapped


TEF1002 – coming soon


FMCFMC VadjSFPSATAPCIeUSB HostSD Card

EthernetFFA & FFBUSB UARTUSB JTAG
TE0710(question), no MGT, 19x diff pair / 38x IO(question)(error)(error)(error)(error)(question), 3.3V B16 I/O(question)(question)(question)(question)
TE0711(question), VCCIO34 B34 I/O on MGT(question)(error)(error)(error)(error), device only(14)(question), 1.8V B16 I/O(error), B34 I/Os(question)(question)(question)
TE0712(question)(tick)(question)(question)(tick)(error), B14 3.3V I/Os(question), 1.8V B13 I/O(tick)(question)(tick)(tick)
TE0713(question)(question)(question)(question)(question)(error), device only(14)(question), 1.8V B13 I/O(error), B13 I/Os(question)(question)(question)
TE0715 (question)(question)(question)(question)(question)(question)(question)(question)(question)(question)(question)
TE0715-30 (question)(question), Max 1.8V(question)(question)(question)(question)(question)(question)(question)(question)(question)

TE0720  (12)

(question), VCCIO34 B34 I/O on MGT(tick)(error)(error)(error)(tick)(tick)(tick)(question)(tick)(tick)

TE0741

(question)(question)(question)(question)(question)(error), B14 3.3V I/Os(error), MGTs(question), MGTs(question)(question)(question)
TE0820 (13)(question)(star), Max 1.8V(tick)(tick)(question)(tick)(tick)(tick)(question)(tick)(tick)
TE0841(question)(question), Max 1.8V(question)(question)(question)(error), B65 3.3V I/Os(error), MGTs(question), MGTs(question)(tick)(tick)
  • (12) FMC_VADJ powers VCCIOC connected to power input of Bank 34 VCCO34 on TE0720 needed to start up. In standard Firmware dip S3-2 can be used to switch ON FMC_VADJ without FMC installed. 
  • (13) FMC_VADJ powers VCCIOC connected to power input of Bank 65 VCCO_65 and VDDO0 of CLK0 on TE0820. In standard Firmware dip S3-2 can be used to switch ON FMC_VADJ without FMC installed. Select VADJ_FMC 1.8V (HP bank)!
  • (14) via FTDI FIFO bridge



  • No labels