Download PDF version of this document.

Overview

The Trenz Electronic TE0813 is an industrial grade MPSoC SOM integrating an AMD ZynqTM UltraScale+TM, DDR4 SDRAM with 64-Bit width data bus connection, SPI Boot Flash memory for configuration and operation, transceivers and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/Os is provided via rugged high-speed stacking connections in a compact 5.2 cm x 7.6 cm form factor.

Refer to http://trenz.org/te0813-info for the current online version of this manual and other available documentation.

Key Features

  • SoC
    • Device: ZU1 / ZU2 / ZU3 / ZU4 / ZU5 1)
    • Engine: CG / EG / EV 1)
    • Speedgrade: -1 / -1L / -2 / -2L / -3 1)
    • Temperature Range: Extended / Industrial 1)
    • Package: SFVC784
  • RAM/Storage
    • 4 GByte DDR4 SDRAM 2)
    • 2 x 64 MByte Serial Flash 3)
    • EEPROM with MAC address
  • On Board
    • Oscillator
  • Interface
    • 4 x B2B Connector (ADM6)
      • up to 204 PL IO

        • HP: 156
        • HD: 0 / 48  4)
      • up to 65 PS MIO

      • 4 GTR
      • 4 GTH (with ZU4 and higher)
      • I2C, JTAG
  • Power
    • 3.3 V power supply via B2B Connector needed 5).
  • Dimension
    • 76 mm x 52 mm
  • Notes
    1) Please, take care of the possible assembly options. Furthermore, check whether the power supply is powerful enough for your FPGA design.
    2) Up to 8 GByte are possible with a maximum bandwidth of 2400 MBit/s.
    3) Please, take care of the possible assembly options.
    4) Please, take care of the possible assembly options.
    5) Dependant on the assembly option a higher input voltage may be possible.

Block Diagram

TE0813 block diagram

Main Components

TE0813 main components
  1. SoC, U1
  2. DDR4, U2, U3, U9, U12
  3. Quad SPI Flash, U7, U17
  4. Connector, JM1, JM2, JM3, JM4
  5. EEPROM, U28
  6. Clock Generator, U5
  7. Oscillator, U6, U32

Initial Delivery State

Storage device name

Content

Notes

DDR4 SDRAMnot programmed
Quad SPI Flashnot programmed
EEPROMnot programmed besides factory programmed MAC address
Programmable Clock Generatornot programmed
Initial delivery state of programmable devices on the module

Signals, Interfaces and Pins

Connectors

Connector TypeDesignatorInterfaceIO CNT 1)Notes
B2BJM1MGT PL4 x MGT (RX/TX)
B2BJM1HP52 SE / 24 DIFF
B2BJM2MGT PS2 x MGT CLK
B2BJM2MGT PS4 x MGT (RX/TX)
B2BJM2CFGJTAG
B2BJM2CFGI2C
B2BJM2CFGMODE
B2BJM3HD48 SE / 24 DIFF
B2BJM3MGT PLMGT CLK
B2BJM3MIO65 GPIO
B2BJM4HP104 SE / 48 DIFF

1) IO CNT depends on assembly variant. E.g. the MGTs are not available for all FPGAs

Board Connectors


Test Points

Test PointSignalNotes1)
TP1PLL_SCLpulled-up to PS_1V8
TP2PLL_SDApulled-up to PS_1V8
TP3DDR4-TENpulled-down to GND
TP4DCDC_2V0
TP5GND
TP6PL_1V8
TP7GND
TP8GND
TP9PL_VCCINT_IO
TP10GND
TP11PL_VCCINT
TP12PL_VCU_0V9
TP13FP_0V85
TP14PS_1V8
TP15GND
TP16DDR_2V5
TP17DDR_PLL
TP18DDR_1V2
TP19PS_GT_1V0
TP20MGTAVTT
TP21VTT
TP22PL_GT_1V15was PL_GT_1V05 in REV01.
TP23VREFA
TP24MGTVCCAUX
TP25MGTAVCC
TP26PL_GT_1V45
TP27PS_PLL
TP28PS_AVTT
TP29LP_0V85
TP30PS_AUX
TP31PS_AVCC
TP34POR_Bpulled-up to PS_1V8

1) Direction:

    • IN: Input from the point of view of this board.
    • OUT: Output from the point of view of this board.
Test Points Information

On-board Peripherals

Chip/InterfaceDesignatorConnected ToNotes

DDR4 SDRAM

U2, U3, U9, U12SoC - PS

Quad SPI Flash

U7, U17SoC - PSBooting.

EEPROM

U28B2B - J2MAC address

Clock Generator

U5SoC, B2B

Oscillator

U6Clock Generator25 MHz

Oscillator

U32SoC33.333333 MHz
On board peripherals

Configuration and System Control Signals

Connector+Pin

Signal Name

Direction1)Description
JM1.A45POR_OVERRIDEINOverride power-on reset delay 2).
JM2.A31ERR_OUTOUTPS error indication 2).
JM2.A34ERR_STATUSOUTPS error status 2).
JM2.A35LP_GOODOUTLow-power domain powered-up. Pulled up to 3.3VIN
JM2.A36PLL_SCLINI2C clock
JM2.A37PLL_SDAIN/OUTI2C data
JM2.A40PG_VCUOUTProgrammable logic powered-up.
JM2.A41EN_PSGTINEnable GTR transceiver power-up.
JM2.A44 / JM2.A45 /
JM2.A46 / JM2.A47
TCK / TDI / TDO / TMSSignal-dependent

JTAG configuration and debugging interface.

JTAG reference voltage: PS_1V8

JM2.B29PG_PSGTOUTGTR transceivers powered-up.
JM2.B30PROG_BIN/OUTPower-on reset 2). Pulled-up to PS_1V8.
JM2.B33SRST_BINSystem reset 2). Pulled-up to PS_1V8.
JM2.B34INIT_BIN/OUTInitialization completion indicator after POR 2). Pulled-up to PS_1V8.
JM2.B37PG_PLOUTVCU powered-up.
JM2.B38EN_FPDINEnable full-power domain power-up.
JM2.B41PG_FPDOUTFull-power domain powered-up.
JM2.B42EN_LPDINEnable low-power domain power-up.
JM2.B45PG_DDROUTDDR power supply powered-up.
JM2.B46DONEOUTPS done signal 2). Pulled-up to PS_1V8.
JM2.B47EN_DDRINEnable DDR power-up.
JM2.C31MRINManual reset.
JM2.C35EN_PLINEnable programable logic power-up.
JM2.C36EN_GT_RINEnable GTH/GTY transceiver power-up.
JM2.C44 / JM2.C45 / JM2.C46 / JM2.C47MODE3..0INBoot mode selection 2):
  • JTAG
  • QUAD-SPI (32 Bit)
  • SD1 (2.0)
  • eMMC (1.8 V)
  • SD1 LS (3.0)

Supported Modes depends also on used Carrier.

JM2.D33PG_GT_ROUTGTH/GTY Transceivers powered-up.
JM2.D37PSBATTINPS RTC Battery supply voltage 2) 3).
JM2.D38PUDC_BINEnable/Disable internal pull-ups during configuration on all SelectIO pins.
JM2.D45 / JM2.D46DX_P / DX_N-SoC temperatur sensing diode pins 2).

1) Direction:

    • IN: Input from the point of view of this board.
    • OUT: Output from the point of view of this board.

2) See UG1085 for additional information.

3) See Recommended Operating Conditions.

Controller signal.

Power and Power-On Sequence


Power Rails

Power Rail Name/ Schematic NameConnector.PinDirection1)Notes
VCCO_66JM1.A32 / JM1.A33IN
VREF_66JM1.A41IN
3.3VINJM1.A54 / JM1.A55 / JM1.B55 / JM1.B56IN

PL_1V8

JM1.C32 / JM1.C33 / JM1.D33 / JM1.D34OUT
PL_DCINJM1.C56 / JM1.C57 / JM1.C58 / JM1.C59 / JM1.C60 / JM1.D56 / JM1.D57 / JM1.D58 / JM1.D59 / JM1.D60IN
LP_DCDCJM2.A50 / JM2.A51 / JM2.A52 / JM2.B50 / JM2.B51 / JM2.B52 / JM2.C50 / JM2.C51 / JM2.C52 / JM2.D50 / JM2.D51 / JM2.D52IN
DCDCINJM2.A57 / JM2.A58 / JM2.A59 / JM2.A60 / JM2.B57 / JM2.B58 / JM2.B59 / JM2.B60 / JM2.C57 / JM2.C58 / JM2.C59 / JM2.C60 / JM2.D57 / JM2.D58 / JM2.D59 / JM2.D60 / IN
PS_BATTJM2.D37IN
DDR_1V2JM2.D47OUT
PS_1V8JM2.C34 / JM2.D34 / JM3.A56 / JM3.B56 / JM3.C56 / JM3.D56OUT
GT_DCDCJM3.A59 / JM3.A60 / JM3.B59 / JM3.B60 / JM3.C59 / JM3.C60 / JM3.D59 / JM3.D60 /IN
VCCO_25JM3.C7 / JM3.C8 / JM3.D8 / JM3.D9IN
VCCO_26JM3.C19 / JM3.C20 / JM3.D20 / JM3.D21IN
VCCO_64JM4.B21 / JM4.B39IN
VREF_64JM4.B30IN
VCCO_65JM4.C21 / JM4.C39IN
VREF_65JM4.C30IN

1) Direction:

    • IN: Input from the point of view of this board.
    • OUT: Output from the point of view of this board.
Module power rails.

Recommended Power up Sequencing

The power up sequencing highly depends on the use case. In general, it should be possible to enable/disable the processing system (PS) / programmable logic (PL) independently. Furthermore, within the processing logic it should be possible to enable/disable only low-power domain and/or low-power and full-power domain. Additionally, usage of GTR for PS side and GTH/GTY for PL side should be possible. Because of this flexibility the needed parts of the following table needs to be selected individually. For detailed information take a look into schematics.

SequenceNet nameRecommended Voltage RangePull-up/downDescriptionNotes
0---Configuration signal setup.See Configuration and System Control Signals.
1 1)PSBATT1.2 V ... 1.5 V-Battery connection.Battery Power Domain usage. When not used, tie to GND.
1 2)3.3VIN3.3 V (± 5 %)-Management power supply.Management module power supply. 0.5 A recommended. Consider note 2) for modules with VCU and/or low-power SoC.
2Processing System (PS):Procedure for PS starting.
2.1Low-power domain:Bring-up for low-power domain PS.
2.1.1LP_DCDC3.3 V (± 3 %) 3)-Low-power domain power supply.Main module power supply for low-power domain. 5.5 A recommended. Power consumption depends mainly on design and cooling solution.
2.1.2EN_LPD-PU 4), 3.3 VLow-power domain power enable.
2.1.3LP_GOOD-PU 4), 3.3 VLow-power domain power good status.Module power-on sequencing for low-power domain finished.
2.2Full-power domain:Bring-up for full-power domain PS.Full-power PS domain needs powered low-power PS domain.
2.2.1DCDCIN3.3 V (± 5 %) 3)
Full-power domain and GTR transceiver power supply.Main module power supply for full-power domain. 7 A recommended. Power consumption depends mainly on design and cooling solution.
2.2.2EN_FPD3.3 V-Full-power domain power enable.
2.2.3PG_FPD-PU 4), 3.3 VFull-power domain power good status.Module power-on sequencing for full-power domain finished.
2.2.4EN_DDR3.3 V-DDR memory power enable.
2.2.5PG_DDR
PU 4), 3.3 VDDR memory power good status.Module power-on sequencing for DDR memory finished.

2.3

GTR TransceiverProcedure for GTR transceiver starting.PS transceiver usage needs powered PS (low- and full-power domain).
2.3.1EN_PSGT3.3 V-GTR transceiver power enable.
2.3.2PG_PSGT-PU 4), 3.3 VGTR transceiver power good status.Module power-on sequencing for GTR transceiver finished.
2Programmable Logic (PL)Procedure for PL starting.PS and PL can be started independently.
2.1PL_DCIN3.3 V (± 5 %) 3) 5)-Programmable logic power supply.Main module power supply for programmable logic. 12 A recommended. Power consumption depends mainly on design and cooling solution.
2.2EN_PL-PU 4), 3.3 VProgrammable logic power enable.
2.3PG_PL-PU 4), 3.3 VProgrammable logic power good status.Module power-on sequencing for programmable logic finished. Periphery and variable bank voltages can be enabled on carrier.
2.4VCCO_25 / VCCO_26 / VCCO_64 / VCCO_65 / VCCO_66 6)-Module bank voltages.Enable bank voltages after PG_PL deassertion.
2.5PG_VCU-PU 4), 3.3 VVCU power good status.
3GTH / GTY TransceiverProcedure for GTH / GTY transceiver starting.PL transceiver usage needs powered PL and low-power PS domain.
3.1GT_DCDC3.3 V (± 3 %) 3)-GTH / GTY transceiver power supply.Main module power supply for GTH / GTY transceiver. 3 A recommended. Power consumption depends mainly on design and cooling solution.
3.2EN_GT_R3.3 V-GTH / GTY transceiver power enable.
3.3PG_GT_R-PU 4), 3.3 VGTH / GTY transceiver power good status.

1) (optional)

2) On TE0813 REV01 boards it is necessary for modules with VCU and/or low-power speedgrade to either connect signal EN_PL to voltage 3.3VIN or to enable EN_PL together with 3.3VIN. This should be changed in a newer revision.

3) Dependent on the assembly option a higher input voltage may be possible. 

4) (on module)

5) This value depends highly on DCDC U4. Higher values may be possible with different DCDCs. For more information consult schematic and according datasheets.

6) See DS925 for additional information.

Baseboard Design Hints

Board to Board Connectors

5.2 x 7.6 cm UltraSoM+ modules use four Samtec AcceleRate HD High-Density Slim Body Arrays on bottom side.
  • 4x ADM6-60-01.5-L-4-2 (240 pins, 60 per row)
    •  Mates with ADF6-60-03.5-L-4-2

5.2 x 7.6 cm UltraSoM+ carrier use four Samtec AcceleRate HD High-Density Slim Body Arrays on top side.

  • 4x ADF6-60-03.5-L-4-2 (160-pins)
    • Mates with ADM6-60-01.5-L-4-2
Features
  • Board-to-Board Connector 240-pins, 60 contacts per row
  • 0.025" (0.635 mm) pitch
  • Data Rate: max 56 Gbps 
  • Mates with: ADM6/APF6
  • Insulator Material: LCP, Black
  • Contact Material:  Copper Alloy
  • Plating: Au or Sn over 50 µ" (1.27 µm) N
  • Operating Temperature Range: -55 ºC to +125 ºC
  • PCIe 5.0 capable: Yes
  • Lead-Free Solderable: Yes
  • RoHS Compliant: Yes
Connector Stacking height

When using the standard type on baseboard and module, the mating height is 5 mm.

Other mating heights are possible by using connectors with a different height:

Order numberREF numberSamtec NumberTypeContribution to stacking heightComment
30095REF-30095ADM6-60-01.5-L-4-2Module connector1.5 mmStandard connector used on modules
31137REF-31137ADF6-60-03.5-L-4-2Baseboard connector3.5 mmStandard connector used on carrier
Connectors.
Connector Speed Ratings

The  AcceleRate HD High-Density  connector speed rating depends on the stacking height; please see the following table:

Stacking heightSpeed rating
5 mm56 Gbps
Speed rating.
Current Rating

Current rating of  Samtec AcceleRate HD High-Density B2B connectors is 1.34 A per pin (4 pins powered)

Connector Mechanical Ratings
  • Shock: 100G, 6 ms Sine
  • Vibration: 7.5G random, 2 hours per axis, 3 axes total


Manufacturer Documentation


Technical Specifications

Absolute Maximum Ratings *)

Power Rail Name/ Schematic NameDescriptionMinMaxUnit
LP_DCDCMicromodule Power-0.3006.0V
DCDCINMicromodule Power-0.3007.0V
GT_DCDCMicromodule Power-0.3006.0V
PL_DCIN 1)Micromodule Power-0.300

4.5

V
3.3VINMicromodule Power-0.3003.600V
PS_BATTRTC / BBRAM-0.5002.000V
VCCO_25HD IO Bank power supply-0.5003.400V
VCCO_26HD IO Bank power supply-0.5003.400V
VCCO_64HP IO Bank power supply-0.5002.000V

VCCO_65

HP IO Bank power supply-0.5002.000V
VCCO_66HP IO Bank power supply-0.5002.000V
VREF_64Bank input reference voltage-0.5002.000V
VREF_65Bank input reference voltage-0.5002.000V
VREF_66Bank input reference voltage-0.5002.000V

1) This value depends on DCDC U4 circuit. If resistor R133 is fitted and R132 is not fitted (default) 7.0 V is allowed. If resistor R133 is not fitted and R132 is fitted only 4.5 V is allowed. For more information consult schematic and according datasheets.

Absolute maximum ratings

*) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these
   or any other conditions beyond those indicated under Recommended Operating Condition. Exposure to absolute-maximum rated conditions for extended periods may affect device reliability.

Recommended Operating Conditions

This TRM is generic for all variants. Temperature range can be different depending on assembly version.  Voltage range is mostly the same during variants (exceptions are possible, depending on custom request)

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

  • Variants of modules are described here: Article Number Information
  • Modules with commercial temperature grade are equipped with components that cover at least the range of 0°C to 75°C
  • Modules with extended temperature grade are equipped with components that cover at least the range of 0°C to 85°C
  • Modules with industrial temperature grade are equipped with components that cover at least the range of -40°C to 85°C
  • The actual operating temperature range will depend on the FPGA / SoC design / usage and cooling and other variables.


ParameterMinMaxUnitsReference Document
LP_DCDC 1)3.2013.399V
DCDCIN 1)3.1353.465V
GT_DCDC 1)3.2013.399V
PL_DCIN 1) 2) 3)3.135

3.465

V
3.3VIN3.1353.465V
PS_BATT1.21.5VSee FPGA datasheet.
VCCO_251.1403.400VSee FPGA datasheet.
VCCO_261.1403.400VSee FPGA datasheet.
VCCO_640.951.900VSee FPGA datasheet.

VCCO_65

0.951.900VSee FPGA datasheet.
VCCO_660.951.900VSee FPGA datasheet.
VREF_640.61.2VSee FPGA datasheet.
VREF_650.61.2VSee FPGA datasheet.
VREF_660.61.2VSee FPGA datasheet.

1) Dependent on the assembly option a higher input voltage may be possible. 

2) This value depends on DCDC U4 circuit. If resistor R133 is fitted and R132 is not fitted (default) 7.0 V are allowed. If resistor R133 is not fitted and R132 is fitted only 4.5 V are allowed. For more information consult schematic and according datasheets.

3) For U4 either TPS548A28RWWR or MPQ8633BGLE-Z is assembled which is up to Trenz Electronic GmbH.

Recommended operating conditions.


Physical Dimensions

  • Module size: 76 mm × 52 mm.  Please download the assembly diagram for exact numbers.

  • Mating height with standard connectors: 5 mm.

PCB thickness: 1.74 mm (± 10 %).

Physical Dimension

Currently Offered Variants 

Trenz shop TE0813 overview page
English pageGerman page
Trenz Electronic Shop Overview

Revision History

Hardware Revision History

Board hardware revision number.


DateRevisionChangesDocumentation Link
-REV02
  1. Change DCDC U11 from EN6347QI to MPM3860GQW-Z and adapted according circuits.
  2. Connected DDR4-TEN signals together for U2, U3, U9, and U12 and pulled them low via 499 Ohm resistor R131.
    Added a testpoint TP3 for DDR4-TEN.
  3. Changed voltage rail from 1.35 V to 1.45 V via adapting voltage divider resistors R33 and R38 and changed according voltage rail name PL_GT_1V35 to PL_GT_1V45.
  4. Changed voltage rail from 1.05 V to 1.15 V via adaption voltage divider resistors R44 and R46 and changed according rail name PL_GT_1V05 to PL_GT_1V15.
  5. Added diode D2 between U41 pin 3 net MR and voltage rail 3.3VIN.
  6. Connected enable signal for U11 and U33 from "3.3VIN" to "PG_PL_VCCINT".
  7. Added capacitors C137, C147, and C148 for VTT voltage rail.
  8. Added resistors R132 (default: not fitted) and R133 to supply U4 VCC either from "PL_DCIN" or from "3.3VIN".
  9. Change resistor R92 from 4.22 kOhm to 9.09 kOhm to set current limit to nearly 14.5 A for U4.
  10. Added remote sense option:
    1. R134 for U30
    2. R135 for U29
    3. R136 for U31
  11. Added decoupling capacitors:
    1. C210 and C211 for U5.
    2. C190 for U7.
    3. C198, C199, and C213 for U8.
    4. C153, C170...172 for U9
    5. C196 C197, and C212 for U10.
    6. C156 and C157 for U12
    7. C207 and C208 for U14.
    8. C189 for U17.
    9. C149...152, C205, and C206 for U18
    10. C209 and C217 for U21.
    11. C214...216 for U22.
    12. C154 and C155 for U24
    13. C188 and C191 for U26.
    14. C187 and C195 for U27.
    15. C203 and C204 for U34.
    16. C201 for U39.
    17. C202 for U40.
    18. C178 for U41.
    19. C200 for U44.
  12. Added testpoints TP4, TP19, TP26.
  13. Added UKCA logo.
  14. Change 100 nF capacitors C135 and C136 from 6.3 V to 25 V for BOM optimization.
REV02
-REV01First Production ReleaseREV01
Hardware Revision History

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Document Change History

DateRevisionContributorDescription

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • Updated TRM to REV02.

2023-03-02

v.43

Martin Rohrmüller

  • Corrected Note 4 about max DDR4 capacity
2023-01-16v.41ED
  • Fixed issue in absolute maximum rating
2023-01-13v.39ED
  • Initial Document

--

all

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • --
Document change history.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]


Table of contents


  • No labels