Download a PDF version of this document.
The Trenz Electronic TE0890 is an module based on AMD Spartan 7 FPGA. It further integrates 8 MByte of HyperRam, 8 MByte of SPI Flash, two user LEDs and 64 IOs.
Refer to http://trenz.org/te0890-info for current online available documentation.
FPGA
RAM/Storage
On Board
Interface
Power
5.0 V single power supply
Dimension
27 mm x 52 mm
Notes
1) Available as assembly variant or upon request.
2) Other sizes/devices, which are pin/package-compatible, upon request.
Storage device name | Content | Notes |
|---|---|---|
HyperRAM, U2 | Not programmed | |
SPI Flash, U3 | Not programmed |
All pin headers are not assembled. Solderability on top or bottom side of PCB is available.
Connector Type | Designator | Interface | IO CNT | Notes |
|---|---|---|---|---|
Pin-Header 2.54 mm | J1 | IO | 16x SE | IOs are a subset of J3 IOs. |
Pin-Header 2.54 mm | J2 | IO | 16x SE | IOs are a subset of J4 IOs. |
Pin-Header 1.27 mm | J3 | IO | 32x SE / 15x DIFF | Shared IOs with J1. |
Pin-Header 1.27 mm | J4 | IO | 32x SE / 15x DIFF | Shared IOs with J2 |
Pin-Header 2.54 mm | J11 | IO | 2x SE |
Test Point | Top | Bottom | Signal | Notes |
|---|---|---|---|---|
TP1 | FPGA pin H1, bank 34 PORT_TP0 | x | PORT_TP0 | GPIO | |
TP2 | FPGA pin H2, bank 34 PORT_TP1 | x | PORT_TP1 | GPIO | |
TP3 | FPGA pin J1, bank 34 PORT_TP2 | x | PORT_TP2 | GPIO | |
TP4 | FPGA pin J2, bank 34 PORT_TP3 | x | PORT_TP3 | GPIO | |
TP5 | FPGA pin L1, bank 34 PORT_TP4 | x | PORT_TP4 | GPIO | |
TP6 | FPGA pin M1, bank 34 PORT_TP5 | x | PORT_TP5 | GPIO | |
TP7 | x | RST_L | Pin: A10, Bank14 IO_L3N | |
TP8 | x | 3.3V | ||
TP9 | x | GND | ||
TP10 | FPGA pin B13, bank 14 PORT_TP6 | x | PORT_TP6 | GPIO | |
TP11 | FPGA pin B14, bank 14 PORT_TP7 | x | PORT_TP7 | GPIO | |
TP12 | x | GND | ||
TP13 | FPGA pin M10, Bank14 IO_25 | x | No net name | GPIO | |
TP14 | x | 1.8V | ||
TP15 | x | 1.0V | ||
TP16 | x | 1.8V | ||
TP17 | x | 1.0V | ||
TP18 | x | 3.3V |
Chip/Interface | Designator | Connected To | Notes |
|---|---|---|---|
AMD Spartan 7 | U1 |
| |
HyperRAM | U2 |
| |
SPI Flash | U6 |
| |
Oscillator | U3 |
|
Signal Name | Connector.Pin | Direction1) | Description |
|---|---|---|---|
FTDI( FTDI_0 / FTDI_1 / FTDI_2 / FTDI_3 ) | J9.2 / J9.4 / J9.5 / J9.6 | Signal dependent | |
JTAG( TCK / TDO / TDI / TMS ) | J10.3 / J10.4 / J10.5 / J10.6 | Signal dependent | |
M2_0 | J5 | IN | Set BOOTMODE:
|
1) Direction:
IN: Input from the point of view of this board.
OUT: Output from the point of view of this board.
Power Rail Name / Schematic Name | Connector.Pin | Direction1) | Notes |
|---|---|---|---|
5V | J1.20 / J2.20 / J3.39 / J4.39 / J9.3 / J11.6 | IN | An active LED D3 (green) indicates power supplied. |
3.3V | J1.10 / J2.10 / J3.19 / J4.19 / J10.1 | OUT |
1) Direction:
IN: Input from the point of view of this board.
OUT: Output from the point of view of this board.
The TE0890 module needs one single power supply of 5.0 V nominal. A power supply with minimum current capability of 1 A is recommended.
The power for the FPGA module can be supplied through any 5V pin of the Pin-Headers J1, J2, J3, J4, J9 or J11.
| Sequence | Net name | Recommended Voltage Range | Pull-up/down | Description | Notes |
|---|---|---|---|---|---|
| - | - | - | - | - |
This TRM is generic for all variants.
Please contact us to inquire options.
Power Rail Name/ Schematic Name | Description | Min | Max | Unit |
|---|---|---|---|---|
| 5V | Supply voltage. | -0.3 | 6.0 | V |
*) Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under "Recommended Operating Condition". Exposure to absolute-maximum rated conditions for extended periods may affect device reliability.
Trenz Electronic classifies modules into temperature range categories by subsumption of its component data (PCB, ICs, connectors, passive components). The temperature ranges are values for ambient air temperature and do not reflect the junction temperature of individual components.
The categories are:
Modules with commercial (C) temperature grade are equipped with components that cover at least the ambient temperature range of 0 °C to 70 °C.
Modules with extended (E) temperature grade are equipped with components that cover at least the ambient temperature range of 0 °C to 85 °C.
Modules with industrial (I) temperature grade are equipped with components that cover at least the ambient temperature range of -40 °C to 85 °C.
These categories do not take into account the entire custom system consisting of:
Customer SoC design. The allowed main SoC temperature range is specified from the vendor by junction temperature using corresponding classes (C, E, I). See vendor documentation.
Cooling solution, active and or passive cooling.
Climate or environmental conditions besides ambient temperature range.
Module orientation, neighbouring assemblies, neither other heat sources nor the SoC as heat source to other components.
Classification of the module can be looked up here: Article Number Information i.e.: TExxxx-xx-xx'I'xx, the 'I' indicates that all components are at least in Industrial temperature class.
The temperature of individual components should not exceed the specified range due to self-heating or heating by adjacent components. The actual operating temperature range will depend on the customer design, usage, environment and cooling solution. Consult Cooling Solutions for more information.
The following table aims to be generic for all variants. The voltage ranges are consistend across assembly variants, but exceptions are possible (custom request).
Parameter | Description | Min | Max | Unit | Reference Document |
|---|---|---|---|---|---|
| 5V | Supply voltage. | 4.75 | 5.25 | V | See schematic. |
Module size: 27 mm × 52 mm. Please download the assembly diagram for exact numbers.
All dimensions are shown in millimeters.
Trenz shop TE0890 overview page | |
|---|---|
The hardware revision number is located on the PCB next to the module identifier, separated by a dash.
Date | Revision | Changes | Documentation Link |
|---|---|---|---|
| 2024-06 | REV02 |
| |
| 2018-10 | REV01 | 1. Change SPI Flash from N25Q064A13ESE40F to IS25LP064D-JBLE. |
Date | Revision | Contributor | Description |
|---|---|---|---|
| |||
-- | all |
|
Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy
The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.
In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.
Products (incl. Software and Firmware) are exclusively designed, manufactured, and distributed for industrial applications. They are not intended, authorized, or certified for use in critical safety applications, medical devices, aerospace, nuclear, life-support, traffic-control, military, or other environments where malfunction or failure could result in personal injury, death, or significant property or environmental damage.
Trenz Electronic GmbH (“Manufacturer”) excludes any liability for inappropriate use in such contexts. The Customer bears all responsibility for verifying suitability and compliance with applicable regulations when deploying in any critical-use scenario. The Customer also agrees to indemnify and hold harmless the Manufacturer from any third-party claims or liabilities arising from such use.
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.
The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.
To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.
REACH
Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).
RoHS
Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.
WEEE
Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.
Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.