Download PDF version of this document.
Table of Contents
The Trenz Electronic TEBT0782 is a carrier for TE0782, TE0783 and TE0784 module.
Refer to http://trenz.org/tebt0782-info for the current online version of this manual and other available documentation.
Storage device name | Content | Notes |
---|---|---|
- | - | - |
The general Reset is provided through button S1 on TE0790 XMOD J7.
Signal | B2B | Note |
---|---|---|
RESIN | JBC3-130 | Board Reset |
FPGA bank number and number of I/O signals connected to the B2B connector:
B2B Connector | Interface | Number of I/O | Notes |
---|---|---|---|
JB1 | RJ45, J1B-J1C | 1 Differential pair, 2 Single Ended | Yellow, Green LEDs |
RJ45, J1A | 4 Differential pair, 8 Single Ended | PHY1 MDIO | |
RJ45, J2B-J2C | 1 Differential pair, 2 Single Ended | Yellow, Green LEDs | |
RJ45, J2A | 4 Differential pair, 8 Single Ended | PHY2 MDIO | |
TE0790 Base, J8 | 4 Single Ended | ||
TE0790 Base, J7 | 1 Single Ended | ||
USB A Stacked, U7 | 2 Single Ended | USB | |
Power Switch, U1 | 2 Single Ended | ||
SMD Line Filter, L6 | 1 Differential pair, 2 Single Ended | USB1_D | |
SMD Line Filter, L7 | 1 Differential pair, 2 Single Ended | USB2_D | |
ESD protection diode, U5 | 1 Single Ended | USB1_VBUS | |
ESD protection diode, U8 | 1 Single Ended | USB2_VBUS | |
JB2 | Module TE078x FPGA, Bank 111-112 | 16 Differential pair, 32 Single Ended | MGT_RX8...15, MGT_TX8...15 |
Module TE078x FPGA, Bank 34 | 1 Differential pair, 2 Single Ended | J1_B34_VRP, J1_B34_VRN | |
Module TE078x FPGA, Bank 34 | 1 Differential pair, 2 Single Ended | J1_B33_VRP, J1_B33_VRN | |
JB3 | TE0790 Base, J8 | 4 Single Ended | M_TCK, M_TMS, M_TDO, M_TDI |
TE0790 Base, J7 | 4 Single Ended 2 Single Ended 1 Single Ended | TCK, TMS, TDO, TDI UART RX/TX RESIN | |
DIP Switch, S1-A | 1 Single Ended | JTAGENB | |
SMA Coaxial, J3...6 | 2 Differential pair, 4 Single Ended | MGT_RX0, MGT_TX0 | |
Module TE0782...4 FPGA, Bank 109-110 | 16 Differential pair, 32 Single Ended | MGT_RX1...7, MGT_TX0...7 |
JTAG access to the TE078x SoM is available through B2B connector JB3. JTAG access is provided by TE0790 XMOD Adapter on Pin Header J7.
JTAG Interface Pins | Signal Name | B2B Connector | Notes |
---|---|---|---|
A | XMOD_A | JB3C-129 | UART |
B | XMOD_B | JB3C-135 | UART |
C | TCK | JB3C-141 | JTAG |
D | TDO | JB3C-148 | JTAG |
E | CPLD_GPIO4 | JB1A-18 | |
F | TDI | JB3C-147 | JTAG |
G | RESIN | JB3C-130 | General Reset |
H | TMS | JB3C-142 | JTAG |
3.3V | 3.3V_M | JB1- JB3 | |
VIO | 3.3V_M | JB1- JB3 | 3.3V |
JTAG access to the System Controller CPLD is provided through B2B connector J3. JTAG access to CPLD is provided by TE0790 XMOD Adapter on Pin Header J8.
Pin 'JTAGENB' must be set high, using DIP Switch S1-A in order to program the System Controller CPLD via JTAG interaface.
JTAG Interface Pins | Signal Name | B2B Connector | Notes |
---|---|---|---|
A | CPLD_GPIO0 | JB1A-10 | |
B | CPLD_GPIO1 | JB1A-12 | |
C | M_TCK | JB3B-81 | |
D | M_TDO | JB3B-88 | |
E | CPLD_GPIO2 | JB1A-14 | |
F | M_TDI | JB3B-87 | |
G | CPLD_GPIO3 | JB1A-16 | |
H | M_TMS | JB3B-82 | |
3.3V | 3.3V_CPLD | JB1- JB3 | |
VIO | 3.3V_CPLD | JB1- JB3 | 3.3V |
DIP Switch S2 on TE0790 must be set and fixed like the following table.
DIP Switch | Setting | Notes |
---|---|---|
S2-1 | ON | JTAGENB (Enable/Disable module JTAG CPLD IOs) |
S2-2 | OFF | NC |
S2-3 | OFF | NC |
S2-4 | OFF | NC |
Signal Name | RJ45-J1 Pin | RJ45-J2 Pin | Notes |
---|---|---|---|
B2B | |||
PHY_MDI0_P | JB1A-23 | JB1A-39 | |
PHY_MDI0_N | JB1A-21 | JB1A-37 | |
PHY_MDI1_P | JB1A-19 | JB1A-35 | |
PHY_MDI1_N | JB1A-17 | JB1A-33 | |
PHY_MDI2_P | JB1A-15 | JB1A-31 | |
PHY_MDI2_N | JB1A-13 | JB1A-29 | |
PHY_MDI3_P | JB1A-11 | JB1A-27 | |
PHY_MDI3_N | JB1A-9 | JB1A-25 | |
J2_TX9_P | JB1A-95 | - | LED Green/Yellow |
J2_TX9_N | JB1A-97 | - | LED Green/Yellow |
J2_RX9_N | - | JB1A-96 | LED Green/Yellow |
J2_RX9_P | - | JB1A-98 | LED Green/Yellow |
The USB A Stacked (U7) is a dual port USB Socket which provides two USB ports.
Signal Name | Port A | Port B | Notes | ||
---|---|---|---|---|---|
B2B | Connected to | B2B | Connected to | ||
USB_D_P | JB1A-28 | SMD Line Filter, L7 | JB1A-40 | SMD Line Filter, L6 | |
USB_D_N | JB1A-26 | SMD Line Filter, L7 | JB1A-38 | SMD Line Filter, L6 | |
USB_VBUS | JB1A-24 | SMD Line Filter, L7 | JB1A-36 | SMD Line Filter, L6 | |
VBUS_V_EN | JB1A-30 | Power Switch, U1 | JB1A-32 | Power Switch, U1 |
The TEBT0782 carrier is equipped with 4x SMA Coaxial straight connectors.
Designator | Schematic | B2B | Notes |
---|---|---|---|
J3 | MGT_TX0_N | JB3A-29 | Transfer |
J4 | MGT_TX0_P | JB3A-31 | Transfer |
J5 | MGT_RX0_N | JB3A-30 | Receive |
J6 | MGT_RX0_P | JB3A-32 | Receive |
Test Point | Signals | B2B Connector | Notes |
---|---|---|---|
TP 1 | VBAT_I | JB3-124 | |
TP 2 | OTG2_ID | JB1-22 | |
TP 3 | OTG1_ID | JB1-34 | |
TP 4 | USB1_VBUS | JB1-36 | |
TP 5 | USB2_VBUS | JB1-24 | |
TP 6 | M_TCK | JB3-81 | |
TP 7 | M_TDO | JB3-88 | |
TP 8 | M_TDI | JB3-87 | |
TP 9 | M_TMS | JB3-82 | |
TP 10 | TCK | JB3-141 | |
TP 11 | TDO | JB3-148 | |
TP 12 | TDI | JB3-147 | |
TP 13 | TMS | JB3-142 | |
TP 14 | VIN | JB1-165...168 | |
TP 15 | 5V | - | |
TP 16 | 3.3V_CPLD | JB1-147...148 | |
TP 17-18 | GND | - |
Chip/Interface | Designator | Notes |
---|---|---|
DIP Switch | S1 |
Switch | Connected to | B2B | Notes |
---|---|---|---|
S1-A | JTABENB | JB3C-136 | |
S1-B...D | - | - | Not connected |
Power supply with minimum current capability of 3A for system startup is recommended.
Power Input Pin | Typical Current |
---|---|
VIN | TBD* |
* TBD - To Be Determined
12V power supply (VIN) on J9/J11 (2 mm MC LB2-A solder-in) or on J10 (TE1.5/2-3.5H).
Power Rail Name | B2B JB1 Pin | B2B JB2 Pin | B2B JB3 Pin | Direction | Notes |
---|---|---|---|---|---|
VIN | 165, 166, 167, 168 | - | - | Input/Output | Directly to module |
3.3V_M | 99, 100, 111,112, 123, 124, 135, 136, 159, 160, 169, 170, 171, 172 | - | 99, 100, 159, 160 | Input/Output | 160, 169, 170, 171, 172 are output other ones input for IO Banks |
3.3V_CPLD | 147,148 | - | - | Output | Directly to module |
1.8V_M | - | 99,100, 159, 160, 169, 170, 171, 172 | 124 | Input/Output | 169, 170, 171, 172 are output other ones input for IO Banks |
VBAT_IN |
Module use 3 x ASP-122952-01 ( QTH–090–01–L–D–A) , (180 pins, "60" per bank) Carrier use 3 x ASP-122953-01 (QSH–090–01–F–D-A), (180 pins, "60" per bank) When using the same type on baseboard, the mating height is 5mm. Other mating heights are possible by using connectors with a different height The module can be manufactured using other connectors upon request. The Q Strip connector speed rating depends on the stacking height; please see the following table: Current rating of Samtec Q Strip Socket B2B connectors is 2A per pin (2 adjacent pins powered). Manufacturer DocumentationConnector Specifications Value Insulator material Black Liquid Crystal Polymer Stacking height 5 mm Contact material Phosphor-bronze Plating Au or Sn over 50 µ" (1.27 µm) Ni Current rating 2 A per pin (2 pins powered) Operating temperature range -55 °C to +125 °C RoHS compliant Yes Connector Mating height
Order number Connector on baseboard compatible to Mating height ASP-122953-01 QTH–090–01–L–D–A 5 mm ASP-122952-01 QSH–090–01–F–D-A 5 mm Connector Speed Ratings
Stacking height Speed rating 5 mm, Single-Ended 9.5 GHz 8 mm, Single-Ended 8.5 GHz 11 mm, Single-Ended 6 GHz 16 mm, Single-Ended 5.5 GHz 20 mm, Single-Ended 3.5 GHz 30 mm, Single-Ended 3 GHz 5 mm, Differential 10.5 GHz / 25Gbit/s 8 mm, Differential 8 GHz 11 mm, Differential 5 GHz 16 mm, Differential 6 GHz 20 mm, Differential 8.5 GHz 30 mm, Differential 1.5 GHz Current Rating
Connector Mechanical Ratings
Symbols | Description | Min | Max | Unit | Note |
---|---|---|---|---|---|
VIN | Input supply voltage | -- | -- | V | Attention: Depends on connected module! 171050601 of the TEBT0782 (-0,3V - 40V) |
T_STG | Storage Temperature | -40 | +85 | °C | DIP Switch S1 |
Operating temperature range depends also on customer design and cooling solution. Please contact us for options.
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
VIN | 11.4 | 12.6 | V | Attention: Depends on connected module! See TE078x TRMs, recommended normally 12V Without module: 171050601 of the TEBT0782 (6V - 36V) |
T_OPT | -40 | +85 | °C |
Module size: 116 mm × 116 mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: 5 mm.
PCB thickness: 1.6 mm.
Trenz shop TEBT0728 overview page | |
---|---|
English page | German page |
Date | Revision | Changes | Documentation Link |
---|---|---|---|
2016-11-05 | 01 | Initial Release | REV01 |
Hardware revision number can be found on the PCB board together with the module model number separated by the dash.
Date | Revision | Contributor | Description |
---|---|---|---|
| |||
2019-10-8 | v.45 | John Hartfiel |
|
2019-10-16 | v.44 | Pedram Babakhani |
|
-- | all |
|
Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy
The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.
In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.
The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.
To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.
REACH
Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).
RoHS
Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.
WEEE
Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.
Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.