Page History
...
This change affects all Trenz Electronic TE0600 SoMs: TE0600-03*.
Affected Product | Replacement |
|---|---|
| TE0600-03-72C11-A | TE0600-04 |
Changes
1) Leds D1 , D5 were changed from 150060VS75000 to SML-P11MTT86
2) R83 was added. R29 was changed from 2.2k to 100
3) U9 was changed from SiT8008AI to SiT8008BI
4) D3 was changed from single BAT54VV,115 to pair BAT54A,215
5) U2 was changed from EN6347QI to MPM3860GQW-Z
6) U3 was changed from EP53F8QI to MPM3834CGPA
7) Stacked vias were removed
8) Net BR0 was connected to GND
9) B2B signal groups information was added
10) Field filename was renamed for all schematic pages
11) Legal Notices page was added
12) System overview and power-on sequencing were added for TE0600.SchDoc page
13) Testpoints TP11 - TP14 , TP23 - TP28 were added
14) R56, R57, R58 were changed from 2k2 to 2k4
15) U12 was fitted for all module assembly variants
16) R36 was changed from 120R to 240R, R84 and T1 were added
17) U4 and U14 were changed from LP3878SD-ADJ to TPS74601PBDRVT
#1 Changed leds (D1, D5) from 150060VS75000 to SML-P11MTT86.
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
Impact:
#1
Type:
Reason:
| -72C11-A | |
| TE0600-03-72C21-A | TE0600-04-72C21-A |
| TE0600-03-52I11-A | TE0600-04-52I11-A |
| TE0600-03-83I21-A | TE0600-04-83I21-A |
| TE0600-03-52I11-M | TE0600-04-52I11-M |
| TE0600-03-83I11-A | TE0600-04-83I11-A |
| TE0600-03-83C21-A (???) | TE0600-04-83C21-A |
| TE0600-03-52I11-W (nicht produziert) ??? | EOL |
| TE0600-03-52I11-C (nicht produziert, müsste S-Variante sein) ??? | EOL |
| TE0600-03IC ??? |
Note ED: 3) U9 was changed from SiT8008AI to SiT8008BI (ED: not changed for replacement variants)
Changes
#2 Changed DCDC EN6347QI (U2) to MPM3860GQW-Z and adapted power circuit.
Type: Schematic Change
Reason: EOL of Component.
Impact: None. Increased current output capability. Minor changes in electrical characteristics.
#2 Changed DCDC EP53F8QI (U3) to MPM3834CGPA and adapted power circuit.
Type: Schematic Change
Reason: EOL of Component
Impact: None. Minor changes in electrical characteristics.
#2 Changed LDO LP3878SD-ADJ (U4, U14) to TPS74601PBDRVT and adapted power circuit.
Type: Schematic Change
Reason: EOL of Component
Impact: None. Increased current output capability. Minor changes in electrical characteristics.
#1 Assembled clock SiT8008BI-73-XXS-100.000000E (U12).
Type: BOM Change
Reason: ???
Impact: ???
#1 Inserted internal pull-up IO resistor option for FPGA via external resistor (R83).
Type: Schematic Change
Reason: Improvement.
Impact: None. Default is as previous revision.
#1 Improve led (D1) driving circuit via adding MOSFET (T1) and resistor (R84) and changed 120 Ohm resistor (R36) to 240 Ohm.
Type: Schematic Change
Reason: Improve led circuit.
Impact: None.
#1 Changed 2.2 kOhm resistor (R29) to 100 Ohm.
Type: BOM Change
Reason: Follow AMD recommendation.
Impact: None.
#1 Changed leds (D1, D5) from 150060VS75000 to SML-P11MTT86.
Type: Schematic Change
Reason: BOM optimization.
Impact: None.
#1 Changed diode (D3) from BAT54VV,115 to two separated diodes (D2, D3) BAT54A,215.
Type: Schematic Change
Reason: BOM optimization.
Impact: None.
#1 Changed 2.2 kOhm resistors (R56, R57, R58) to 2.4 kOhm.
Type: BOM Change
Reason: Follow AMD recommendation.
Impact: None.
#1 Pulled-down board revision signal (FPGA U5, pin P17) and updated board revision documentation.
Type: Schematic Change
Reason: Update revision information.
Impact: None. Firmware reflects it but custom firmware needs to be updated by customer.
#11 Added testpoints (TP11...TP14, TP23...TP28).
Type: PCB Change
Reason: Improve voltage monitoring.
Impact: None.
#1 Changed stacked vias to staggered vias.
Type: PCB Change
Reason: Reliability improvement.
Impact: Reliablity improvement.
#20 Signal trace lengths changed
Type: PCB change
Reason: Result of changes above.
Impact: Changed trace length have to be taken into account in existing designs.
#17 Updated B2B documentation.
Type: Documentation Update
Reason: Documentation improvement.
Impact: None.
#17 Renamed document sheets.
Type: Documentation Update
Reason: Documentation improvement.
Impact: None.
#20 Updated legal notices, revision history, block and power diagram. Updated page count and order.
Type: Documentation Update
Reason: Documentation improvement.
Impact: None.Impact:
| Scroll Pagebreak |
|---|
Method of Identification
...
Contact Information
If you have any questions related to this PCN, please contact Trenz Electronics Technical Support at
- forum.trenz-electronic.de
- wiki.trenz-electronic.de
- support%trenz-electronic.de (subject = PCN-JJJJMMDD20240124)
phone
national calls: 05741 3200-0
international calls: 0049 5741 3200-0
Disclaimer
Any projected dates in this PCN are based on the most current product information at the time this PCN is being issued, but they may change due to unforeseen circumstances. For the latest schedule and any other information, please contact your local Trenz Electronic sales office, technical support or local distributor.
...
Overview
Content Tools