Page History

Custom_table_size_100

Page properties

hidden	true
id	Comments

Design Name always "TE Series Name" + optional CPLD Name + "CPLD"

Date	Version	Changes	Author
2023-02-07	2.2	added column 'Firmware release' in 'Document Change History' table changed template revision from list to table	ma
-	2.1	Fix problem with pdf export and side scroll bar	-
-	2.0	add fix table of content add table size as macro removed page initial creator	-

Overview

Firmware for PCB-Master CPLD with designator U17. Use first CPLD Device in Chain: LCMX02-1200HC.

Firmware for PCB-Slave CPLD with designator U39. Use second CPLD Device in Chain: LCMX02-1200HC.

There are 3 different Firmware variants available:

(Default): SCM_07A_default.jed/SCS_07A_default.jed
(optional): SCM_07B_powerdown_disabled.jed/SCS_07B_powerdown_disabled.jed - Power down Sequencing is disabled (See Note Power Managment).
(optional): SCM_07C_msdboot_disabled.jed/SCS_07C_msdboot_disabled.jed - CD Pin of MicroSD will not influence boot Mode (mircoSD can be used as Filesystem and system Boots from QSPI)

Feature Summary

Power Management (Slave CPLD)
Reset Management (both)
- SOM,USB,ETH,PCIE,ETH
CPLD JTAG (both)
FMC JTAG / PJTAG (Master CPLD)
FMC VADJ Power (Master CPLD)
Boot Mode (Slave CPLD)
PCIe (Slave CPLD)
SD (both)
UART SoC (Slave CPLD)
UART (Debug) (Master CPLD)
CAN (Master CPLD)
USB (Master CPLD)
DisplayPort (Master CPLD)
SFP (Master CPLD)
I2C (Master CPLD)
LEDs (both)
RGPIO (both)

Firmware Revision and supported PCB Revision

See Document Change History

Product Specification

Port Description

Light green rows are Master CPLD ports and light geen rows are Slave CPLD ports.

Name / opt. VHD Name	Direction	Pin	Pullup/Pulldown	Bank Power	Description	CPLD
C_T1		24	--	3V3SB	/ currently_not_used	U17
C_T2		26	--	3V3SB	/ currently_not_used	U17
C_T3		25	--	3V3SB	/ currently_not_used	U17
C_TCK	in	131	None	3V3SB	JTAG J28 (XMOD2) / FMC JTAG	U17
C_TDI	in	136	Up	3V3SB	JTAG J28 (XMOD2) / FMC JTAG	U17
C_TDO1 / C_TDO	out	137	None	3V3SB	JTAG J28 (XMOD2) / FMC JTAG	U17
C_TMS	in	130	None	3V3SB	JTAG J28 (XMOD2) / FMC JTAG	U17
CAN_FAULT		106	Up	3V3SB	CAN	U17
CAN_RX	in	107	Down	3V3SB	CAN	U17
CAN_S	out	105	None	3V3SB	CAN	U17
CAN_TX	out	104	None	3V3SB	CAN	U17
CLK_125MHz / PHY_CLK	in	70	Down	1.8V	/ currently_not_used	U17
CON_NTRST / JTAG_TRST	in	117	Up	3V3SB	JTAG, Connector J30	U17
CON_RTCK / JTAG_RTCK	out	125	None	3V3SB	JTAG, Connector J30	U17
CON_sRST / JTAG_SRST	in	127	Up	3V3SB	JTAG, Connector J30	U17
CON_TCK / JTAG_TCK	in	122	Down	3V3SB	JTAG, Connector J30	U17
CON_TDI / JTAG_TDI	in	119	Down	3V3SB	JTAG, Connector J30	U17
CON_TDO / JTAG_TDO	out	126	None	3V3SB	JTAG, Connector J30	U17
CON_TMS / JTAG_TMS	in	121	Up	3V3SB	JTAG, Connector J30	U17
DIR_T1		23	--	3V3SB	/ currently_not_used	U17
DIR_T2		28	--	3V3SB	/ currently_not_used	U17
DIR_T3		27	--	3V3SB	/ currently_not_used	U17
DP_AUX_DE / DP_DE	out	92	None	3V3SB	Display Port	U17
DP_AUX_RX / DP_RX	in	91	Up	3V3SB	Display Port	U17
DP_AUX_TX / DP_TX	out	93	None	3V3SB	Display Port	U17
DP_EN	out	77	None	3V3SB	Display Port	U17
DP_TX_HPD / DP_HPD	in	94	Up	3V3SB	Display Port	U17
ETH_RST	out	62	None	1.8V	ETH Reset	U17
EX_IO1		112	--	3V3SB	/ currently_not_used	U17
EX_IO2		113	--	3V3SB	/ currently_not_used	U17
EX_IO3		114	--	3V3SB	/ currently_not_used	U17
EX_IO4		115	--	3V3SB	/ currently_not_used	U17
F2_EN		19	--	3V3SB	/ currently_not_used	U17
F2PWM		20	--	3V3SB	/ currently_not_used	U17
F2SENSE		21	--	3V3SB	/ currently_not_used	U17
FMC_CLK_DIR / FMC_CLKDIR	in	73	None	3V3SB	FMC	U17
FMC_TCK	out	95	None	3V3SB	FMC	U17
FMC_TDI	out	96	None	3V3SB	FMC	U17
FMC_TDO	in	97	Down	3V3SB	FMC	U17
FMC_TMS	out	98	None	3V3SB	FMC	U17
FMC_VID0	out	139	Down	3V3SB	FMC	U17
FMC_VID1	out	140	Up	3V3SB	FMC	U17
FMC_VID2	out	141	Down	3V3SB	FMC	U17
GND		84	--	3V3SB	REV03 unconnected / currently_not_used	U17
HDIO_SC10 / SC10	out	60	Down	1.8V	FPGA / DP_RX or 'Z'	U17
HDIO_SC11 / SC11	in	59	Down	1.8V	FPGA / DP_DE	U17
HDIO_SC12 / SC12	out	58	None	1.8V	FPGA / DP_HPD	U17
HDIO_SC13 / SC13	out	57	None	1.8V	FPGA / RGPIO TX	U17
HDIO_SC14 / SC14	in	56	None	1.8V	FPGA / RGPIO RX	U17
HDIO_SC15 / SC15	in	55	Up	1.8V	FPGA / RGPIO CLK	U17
HDIO_SC16 / SC16	in	54	Down	1.8V	FPGA / CAN_S	U17
HDIO_SC17 / SC17	in	52	Up	1.8V	FPGA / XMOD LED	U17
HDIO_SC18 / SC18	in	68	Down	1.8V	FPGA / CAN_TX	U17
HDIO_SC19 / SC19	out	69	None	1.8V	FPGA / CAN_RX	U17
I2C_RST	out	61	None	1.8V	I2C	U17
JTAGENB		120	--	3V3SB	external Pin for CPLD Firmware Update	U17
LED_1A / JLED1	out	109	None	3V3SB	USB3.0 LED Jellow	U17
LED_2A / JLED2A	out	111	None	3V3SB	USB3.0 LED Green/Orange	U17
LED_2B / JLED2B	out	110	None	3V3SB	USB3.0 LED Green/Orange	U17
MIO26	out	41	Down	1.8V	MIO / PJTAG	U17
MIO27	out	40	Down	1.8V	MIO / PJTAG	U17
MIO28	in	39	Down	1.8V	MIO / PJTAG	U17
MIO29	out	38	Down	1.8V	MIO / PJTAG	U17
OCLK_EN / OSC_EN	out	74	None	3V3SB	Programmable Oscillator U45	U17
PHY_CONFIG	out	65	None	1.8V	ETH PHY	U17
PHY_LED0	in	67	Down	1.8V	ETH PHY	U17
PHY_LED1	in	86	Down	3V3SB	ETH PHY	U17
PHY_LED2	in	85	Down	3V3SB	ETH PHY	U17
SC_CLK0 / CLK0	in	76	Down	3V3SB	/ currently_not_used	U17
SC_CLK1 / CLK1	in	75	Down	3V3SB	/ currently_not_used	U17
SC_IO0 / X0	out	50	None	1.8V	MTS dummy	U17
SC_IO1 / X1	in	49	Up	1.8V	internal cpld RGPIO CLK	U17
SC_IO2 / X2	out	48	None	1.8V	internal cpld RGPIO TX	U17
SC_IO3 / X3	in	47	Down	1.8V	internal cpld RGPIO RX	U17
SC_IO4 / X4	out	45	None	1.8V	SD WP to slave cpld	U17
SC_IO5 / X5	in	44	--	1.8V	STM dummy	U17
SC_IO6 / X6	in	43	Up	1.8V	internal ETH Reset from Slave to Master CPLD	U17
SC_IO7 / X7	out	42	None	1.8V	/ currently_not_used	U17
SC_IO8 / X8	in	22	--	3V3SB	internal cpld RGPIO available(1.8V on)	U17
SC_SCL / SCL	in	14	Up	3V3SB	I2C Mux U27 / currently_not_used	U17
SC_SDA / SDA	in	13	Up	3V3SB	I2C Mux U27 / currently_not_used	U17
SC2_SW3 / SW3	in	6	Up	3V3SB	DIP-Switch S5-3	U17
SC2_SW4 / SW4	in	5	Up	3V3SB	DIP-Switch S5-4	U17
SD_WP	in	100	Up	3V3SB	MMC SDWP	U17
SFP_LED1 / SFP_LED0	out	81	None	3V3SB	SFP	U17
SFP_LED2 / SFP_LED1	out	82	None	3V3SB	SFP	U17
SFP_LED3 / SFP_LED2	out	78	None	3V3SB	SFP	U17
SFP_LED4 / SFP_LED3	out	83	None	3V3SB	SFP	U17
SFP1_LOS		32	--	3V3SB	SFP / currently_not_used	U17
SFP1_TX_DIS	out	33	None	3V3SB	SFP	U17
SFP2_LOS		35	--	3V3SB	SFP / currently_not_used	U17
SFP2_TX_DIS	out	34	None	3V3SB	SFP	U17
STAT_LED0 / LED0	out	99	None	3V3SB	LED D4 Green	U17
STAT_LED1 / LED1	out	128	None	3V3SB	LED D1 Red	U17
USB0_RST / USB_RST		71	None	1.8V	USB (U9) PHY Reset	U17
USBH_LED_G3		11	--	3V3SB	USB Hub (U4) / currently_not_used	U17
USBH_LED_G4		12	--	3V3SB	USB Hub (U4) / currently_not_used	U17
USBH_LED_SS1		9	--	3V3SB	USB Hub (U4) / currently_not_used	U17
USBH_LED_SS2		133	--	3V3SB	USB Hub (U4) / currently_not_used	U17
USBH_LED_SS3		132	--	3V3SB	USB Hub (U4) / currently_not_used	U17
USBH_LED_SS4		138	--	3V3SB	USB Hub (U4) / currently_not_used	U17
USBH_MODE0	out	142	None	3V3SB	USB Hub (U4)	U17
USBH_MODE1	out	143	None	3V3SB	USB Hub (U4)	U17
USBH_RST	out	10	None	3V3SB	USB Hub (U4)	U17
XMOD1_A / XMOD_TXD	out	3	Up	3V3SB	J28 (XMOD 2 UART)	U17
XMOD1_B / XMOD_RXD	in	2	Up	3V3SB	J28 (XMOD 2 UART)	U17
XMOD1_E / XMOD_E	out	4	None	3V3SB	J28 (XMOD 2 LED)	U17
XMOD1_G / XMOD_G	out	1	Up	3V3SB	J28 (XMOD 2 Button)	U17
1.8V_EN / EN_1V8	out	106	None	3V3SB	Enable 1.8V Power	U39
5V_EN / EN_5V	out	115	Up	3V3SB	Enable 5V Power, can be permanently enabled by S4-4	U39
C_TCK		131	--	3V3SB	JTAG J28 (XMOD2) / currently_not_used	U39
C_TDO	out	137	None	3V3SB	JTAG J28 (XMOD2)	U39
C_TDO1 / C_TDI	in	136	Up	3V3SB	JTAG J28 (XMOD2)	U39
C_TMS		130	--	3V3SB	JTAG J28 (XMOD2) / currently_not_used	U39
CLK_A / AUD_CLK	out	1	Down	1.8V	AUDIO U3 CLK	U39
CLK_CPLD / MEMS_CLKIN	in	128	None	3V3SB	U25 24,576MHz	U39
DONE	in	67	Up	1.8V	PS Done	U39
EN_DDR	out	86	None	3V3SB	Enable Module DDR Power	U39
EN_FMC / FMC_EN	out	104	None	3V3SB	FMC	U39
EN_FPD	out	81	None	3V3SB	Enable Module PS FPD Power	U39
EN_GT_L	out	77	None	3V3SB	Enable Module GT Power	U39
EN_GT_R	out	93	None	3V3SB	Enable Module GT Power	U39
EN_LPD	out	84	None	3V3SB	Enable Module PS LPD Power	U39
EN_PL	out	95	None	3V3SB	Enable Module PL Power	U39
EN_PLL_PWR	out	78	None	3V3SB	Enable Module SI5345 Power	U39
EN_PSGT / EN_PSGTR	out	75	None	3V3SB	Enable Module PS GT Power	U39
ERR_OUT / ERROR	in	70	Up	1.8V	Module PS Error Out / Status	U39
ERR_STATUS / ERR_STAT	in	69	Up	1.8V	Module PS Error Status	U39
F1PWM	out	121	None	3V3SB	FAN1	U39
F1SENSE	in	125	Up	3V3SB	FAN1	U39
FAN_FMC_EN / FMC_FAN_EN		132	None	3V3SB	FMC FAN	U39
FMC_PG_C2M	out	141	Up	3V3SB	FMC PG	U39
HD_LED_N / HDLED_N	out	112	None	3V3SB	J10 HD LED	U39
HD_LED_P / HDLED_P	out	110	None	3V3SB	J10 HD LED	U39
HDIO_SC0 / SC0	in	32	Down	1.8V	FPGA IO / forward to HD_LED_P / HDLED_P	U39
HDIO_SC1 / SC1	in	33	Down	1.8V	/ currently_not_used	U39
HDIO_SC2 / SC2	in	34	Down	1.8V	/ currently_not_used	U39
HDIO_SC3		35	--	1.8V	/ currently_not_used	U39
HDIO_SC4		25	--	1.8V	/ currently_not_used	U39
HDIO_SC5 / SC5	out	26	None	1.8V	FPGA IO / RGPIO	U39
HDIO_SC6 / SC6	in	27	Up	1.8V	FPGA IO / RGPIO CLK	U39
HDIO_SC7 / SC7	in	28	Down	1.8V	.FPGA IO / RGPIO	U39
I2C_SCL / SCL	in	50	Up	1.8V	I2C / currently_not_used	U39
I2C_SDA / SDA	in	52	Up	1.8V	I2C / currently_not_used	U39
INIT_B / INIT	in	68	Up	1.8V	Module PS Init_B	U39
JTAGENB		120	--	3V3SB	external Pin for CPLD Firmware Update	U39
LP_GOOD / PG_LPD	in	83	Up	3V3SB	Module LP Power Good	U39
MIO24		38	Up	1.8V	MIO / currently_not_used	U39
MIO25		39	--	1.8V	MIO / currently_not_used	U39
MIO30	in	48	None	1.8V	MIO / USB Reset	U39
MIO31	in	49	None	1.8V	MIO / PCIe Reset	U39
MIO32		40	--	1.8V	MIO / currently_not_used	U39
MIO33		41	--	1.8V	MIO / currently_not_used	U39
MIO34		42	--	1.8V	MIO / currently_not_used	U39
MIO35		43	--	1.8V	MIO / currently_not_used	U39
MIO36		44	--	1.8V	MIO / currently_not_used	U39
MIO37		45	--	1.8V	MIO / currently_not_used	U39
MIO40	in	54	Up	1.8V	MIO	U39
MIO41		55	--	1.8V	MIO / currently_not_used	U39
MIO42	out	60	None	1.8V	MIO	U39
MIO43	in	61	Up	1.8V	MIO	U39
MIO44		47	None	1.8V	MIO	U39
MOD_EN	out	119	None	3V3SB	Enable Main Module Power 3.3V	U39
MODE0	out	6	None	1.8V	Module Boot Mode	U39
MODE1	out	9	None	1.8V	Module Boot Mode	U39
MODE2	out	10	None	1.8V	Module Boot Mode	U39
MODE3	out	11	None	1.8V	Module Boot Mode	U39
MR / MRESETn	out	92	None	3V3SB	Module PS Power Reset	U39
PCI_SFP_EN	out	76	None	3V3SB	SFP	U39
PER_EN	out	117	None	3V3SB	Enable 3.3V power	U39
PERST / PERSTn	out	139	None	3V3SB	PCIE Resetn	U39
PG_DDR	in	91	Up	3V3SB	Module Power Good	U39
PG_FPD	in	85	Up	3V3SB	Module Power Good	U39
PG_GT_L	in	96	Up	3V3SB	Module Power Good	U39
PG_GT_R	in	94	Up	3V3SB	Module Power Good	U39
PG_PL	in	82	Up	3V3SB	Module Power Good	U39
PG_PLL_1V8 / PG_PLL	in	73	Up	3V3SB	Module Power Good	U39
PG_PSGT	in	74	Up	3V3SB	Module Power Good	U39
PLL_LOLn / PLL_LOL	in	58	Up	1.8V	Module PLL / currently_not_used	U39
PLL_RST / PLL_RSTn	out	56	None	1.8V	Module PLL Reset	U39
PLL_SEL0	out	57	None	1.8V	Module PLL	U39
PLL_SEL1	out	59	None	1.8V	Module PLL	U39
POK_1V8	in	107	Up	3V3SB	Carrier Power Good	U39
POK_FMC	in	99	Up	3V3SB	FMC Power Good	U39
PROG_B	OUT	71	Up	1.8V	Module PS_PROG_B	U39
PSON	out	105	None	3V3SB	ATX J20 PS_ON_N	U39
PWR_BTN	in	113	Up	3V3SB	Power Button S1 or J10	U39
PWRLED_N / LED_N	out	111	None	3V3SB	J10 PWR	U39
PWRLED_P / LED_P	out	109	None	3V3SB	J10 PWR	U39
PWROK	in	100	Up	3V3SB	ATX J20 PWROK	U39
RST_BTN	in	114	Up	3V3SB	Reset Button S2 or J10	U39
S_1		127	--	3V3SB	BEEPER / currently_not_used	U39
SC_IO0 / X0	in	12	None	1.8V	MTS dummy	U39
SC_IO1 / X1	out	13	None	1.8V	internal cpld RGPIO CLK	U39
SC_IO2 / X2	in	14	None	1.8V	internal cpld RGPIO RX	U39
SC_IO3 / X3	out	20	None	1.8V	internal cpld RGPIO TX	U39
SC_IO4 / X4	in	21	Up	1.8V	MMC SD WP from master	U39
SC_IO5 / X5	out	22	None	1.8V	STM dummy	U39
SC_IO6 / X6	out	23	None	1.8V	internal ETH Reset from Slave to Master CPLD	U39
SC_IO7 / X7	in	24	Down	1.8V	/ currently_not_used	U39
SC_IO8 / X8	out	126	Down	3V3SB	internal cpld RGPIO available(1.8V on)	U39
SC2_SW1 / SW1	in	133	Up	3V3SB	S5-1 / Boot Mode Selection	U39
SC2_SW2 / SW2	in	138	Up	3V3SB	S5-2 / Boot Mode Selection	U39
SD_A_EN	out	140	None	3V3SB	Micro SD	U39
SD_B_EN	out	122	None	3V3SB	MMC SD	U39
SD_CD / SD_CD_OUT	out	65	None	1.8V	SD Card detect to FPGA	U39
SD_CD_B	in	143	Up	3V3SB	MMC SD CD	U39
SD_CD_S	in	142	Up	3V3SB	Micro SD CD	U39
SEL_SD / SD_SEL	out	62	None	1.8V	SD select (Mirco or MMC)	U39
SRST_B / SRSTn	out	19	None	1.8V	Module PS_SRST_B	U39
STAT_LED2 / LED2	out	98	None	3V3SB	LED D6 Green	U39
STAT_LED3 / LED3	out	97	None	3V3SB	LED D7 Red	U39
XMOD2_A / XMOD_TXD	out	5	None	1.8V	J12 (XMOD 1 UART)	U39
XMOD2_B / XMOD_RXD	in	4	Up	1.8V	J12 (XMOD 1 UART)	U39
XMOD2_E / XMOD_LED	out	3	Down	1.8V	J12 (XMOD 1 LED)	U39
XMOD2_G / XMOD_BTN	in	2	Up	1.8V	J12 (XMOD 1 Button)	U39

Functional Description

JTAG

JTAGENB set carrier board CPLD into the chain for firmware update. For Update set DIP S4-3 to ON.

Power

FMC VADJ is handled on master CPLD.

DIP	Positon	Description
S5-4	ON	1.8V
S5-4	OFF	1.2V

Power on and off sequencing is done with slave CPLD.

Scroll Title

anchor	Figure_power
title	Power On/OFF Sequencing

draw.io Diagram

border	false
viewerToolbar	true

fitWindow	false
diagramDisplayName
lbox	true
revision	45
diagramName	power_seq
simpleViewer	true
width	1200
links	auto
tbstyle	top
diagramWidth	21702174
height	19861987

Note: Power downs sequencing above can be disabled with second optional CPLD Firmware:

Configure Firmware version SCM_07B8P0_powerdownauto_disabledboot.jed/SCS_07B8P0_powerdownauto_disabledboot.jed
Add Jumper to J10-6 and J10-8 instead of Enclousure Enclosure Button
Module will be powered and boot on with Main power supply.

Reset

Power, Zynq reset and PCIe is handle on Slave CPLD

USB, ETH, I2C Reset is handled on Master CPLD

Type	controlled by
PCie	Power On Reset_N(pwr_rdy), MIO31
USB(PHY+HUB)	Power On Reset_N(pwr_rdy), MIO30
Modul PLL	Power On Reset_N(pwr_rdy)
PS_POR_B	Reset Button (hold long time ~3s), zynq_reset_ready
PS_SRST_B	Reset Button (hold short time ~1s), zynq_reset_ready
FMC_FAN_EN	Power On Reset_N(pwr_rdy)
I2C_RST	Power On Reset_N(pwr_rdy)
ETH_RST	Power On Reset_N(pwr_rdy), MIO24

JTAG

CPLD JTAG only needed for CPLD Firmware update.

FMC and CPLD JTAG is accessable over XMOD2(J28).

S4-3
ON	CPLD Access on both CPLD
OFF	FMC JTAG Access

PJTAG on connector J17 is routed over Master CPLD to MIO26..29.

Signal	Connection
JTAG_TCK	MIO26
JTAG_RTCK	JTAG_TCK
JTAG_TDI	MIO27
JTAG_TDO	MIO28
JTAG_TMS	MIO29
JTAG_SRST	not usedconnected only to FPGA RGPIO
JTAG_TRST	not used, connected only to FPGA RGPIO

Boot Mode

Boot Mode is handled on Slave CPLD.

S5-1	S5-2	Description
ON	ON	Default, boot from SD/microSD or SPI Flash if no SD is detected
OFF	ON	Boot from eMMC
ON	OFF	Boot mode PJTAG0
OFF	OFF	Boot mode main JTAG

Note: There is a second CPLD Variant available, where microSD will not change the boot mode.

Configure Firmware version SCM_07C_msdboot_disabled.jed/SCS_07C_msdboot_disabled.jed
Boot mode will be still QSPI,when microSD is insered.

PCIe

PCIe is handled on Slave CPLD.

Signal	Connection
PERSTn	Power On reset and MIO31

SD

SD is mainly handled on Slave CPLD

SD Signal	Description
SD_SEL	CD Pin form microSD selects the SD Card, microSD has higher priority
CD (MIO45)	mircoSD and SD Card detect
WP(MIO44)	0 when miroSD is used else SD card detect (forrward over Master CPLD)

UART SoC

SoC(ZynqMP) is accessible over XMOD1(J12) and connected to ZynqMP over Slave CPLD

Signal	Description
XMOD_TXD	ZynqMP TX(MIO43), when PWR Ready else 1
XMOD_RXD	to ZynqMP RX(MIO42), when PWR Ready else 1

UART (Debug)

Simple Firmware Debug UART is accessible over XMOD2(28) over Master CPLD

Firmware Versions and some statistics can be displayed over second XMOD:

Included since CPLD Firmware Update to REV07
UART Speed is 115200
Press XMOD Button to see output, otherwise RX/TX are loop backed

Signal	Description
XMOD_TXD	Debug output, when XMOD Button is pressed else RX loopback
XMOD_RXD	Debug input(currently no function), when XMOD Button is pressed else TX loopback

CAN

CAN is handled mainly on Master CPLD

Signal	Description
CAN_TX	SC18(FPGA LOC depends on module)
CAN_RX	SC19(FPGA LOC depends on module)
CAN_S	SC16(FPGA LOC depends on module)
CAN_FAULT	Monitoring over RGPIO only

USB

USB Reset is handled mainly on Master CPLD

Signal	Description
USB_RST	Power On Reset_N and MIO30 (over slave CPLD)
USBH_RST	Power On Reset_N and MIO30 (over slave CPLD)
USBH_MODE0	const 1
USBH_MODE1	const 1

DisplayPort

DisplayPort is handled on Master CPLD

Signal	Description
DP_EN	Power On Reset_N
DP_RX	to SC10 when SC11 is 0 else Z
DP_TX	SX10
DP_DE	SC11
DP_HPD	SC12

SFP

ETH Reset is handled on Master CPLD

Signal	Description
SFP1_TX_DIS	const 0 (Enabled)
SFP2_TX_DIS	const 0 (Enabled)

I2C

I2C MUX is handled on Master CPLD

Signal	Description
I2C_RST	Power On Reset_N

ETH

ETH Reset is handled on Master CPLD

Signal	Description
ETH_RST	Power On Reset_N and MIO24 (over slave CPLD)
PHY_CONFIG	const 1

LEDs

LEDs are handled on both CPLDs.

They used different Blink Sequence to indicate all state:

******** (slow blinking)	~0,7 Hz	continuous blinking, like SFP LEDs or Enclosure HD LED when board is powered down
******** (fast blinking)	~5,8 Hz	continuous blinking, like D6 LED or Enclosure Power LED when board is powered down
*****ooo	~0,7 Hz, duty cycle 5/8	5 times fast blink with a break
****oooo	~0,7 Hz, duty cycle 4/8	4 times fast blink with a break
***ooooo	~0,7 Hz, duty cycle 3/8	3 times fast blink with a break
**oooooo	~0,7 Hz, duty cycle 2/8	2 times fast blink with a break
*ooooooo	~0,7 Hz, duty cycle 1/8	1 times fast blink with a break
ON	---	LED ON
OFF	---	LED OFF

Designator

Color

Usage

Description

D7

Red

status

Priority	Description	Blink sequencing
1	PS POR Reset pressed long time (or whole system is powered off)	ON
2	PS Soft Reset pressed short time	OFF
3	SD Boot	*ooooooo
4	QSPI Boot	**oooooo
5	eMMC Boot	***ooooo
6	PJTAG Boot	****oooo
7	JTAG Boot	*****ooo
8	Error	******** (fast blinking)

D6

Green

status

Priority	Description	Blink sequencing
1	Power OFF	******** (fast blinking)
2	PG_LPD low	*****ooo
3	PG_FPD low	****oooo
4	PG_PL low	***ooooo
5	PG_DDR low or PG_PSGT low or PG_PLL low or PG_GT_L low or PG_GT_R low	**oooooo
6	POK_1V8 low or POK_FMC low or perihpery_pg low or (Main Power State Machine Ready and FMC Sanity check low)	*ooooooo
7	Main Power State Machine Ready	OFF
8	ERROR some power failed, see XMOD LEDs	ON

J10 Power LED

Blue (symbol light bulb)

status/user

Priority	Description	Blink sequencing
1	power button pressed long time forced power down	******** (fast blinking)
2	Main Power State Machine Idle and Power of State is off	******** (slow blinking)
3	power button pressed short time power to power on/off	*****ooo
4	PS reset button pressed long time	****oooo
5	PS reset button pressed short time	***ooooo
6	power down sequencing is running	**oooooo
7	whole system hold into reset	*ooooooo
8	MIO40	User Defined

J10 HD LED

Red (symbol drive)

status/user

Priority	Description	Blink sequencing
1	PS Init is low	******** (fast blinking)
2	PS Error High	*****ooo
3	PS Error Status High	****oooo
4	SOC Done low	***ooooo
5	SC0	User Defined

XMOD1 D4

Red

status

Priority	XMOD Button	Description	Blink sequencing
1	Pressed	power button pressed long time forced power down	******** (fast blinking)
2	Pressed	Main Power State Machine Idle and Power of State is power down sequencing	*****ooo
3	Pressed	PS reset button pressed	****oooo
4	Pressed	Power button pressed short time power on/off	***ooooo
5	Pressed	Power of State is power down sequencing	**oooooo
6	Pressed	System hold into reset	*ooooooo
7	Pressed	PS Init low	ON
1	Unpressed	Problem with other CPLD, FMC is disabled	******** (fast blinking)
2	Unpressed	Main Power State Machine Wait Ready ON/OFF	*****ooo
3	Unpressed	Main Power State Machine 3.3V and VADJ ON/OFF	****oooo
4	Unpressed	power not ready (power reset)	**oooooo
5	Unpressed	zynq reset	*ooooooo
7	Unpressed	PS Init low	ON
x	Pressed/Unpressed	all fine	OFF

XMOD2 D4

Red

status/user

Priority	Description	Blink sequencing
1	Power On Reset	******** (slow blinking)
2	PS Init low	******** (fast blinking)
3	SC17	User Defined

SFP D1

Red

status/user

Priority	Description	Blink sequencing
1	Power On Reset	******** (slow blinking)
2	PS Init low	******** (fast blinking)
3	RGPIO(0), when RGPIO Enabled over FPGA	User Defined
4	--	OFF

SFP D8

Green

status/user

Priority	Description	Blink sequencing
1	Power On Reset	******** (slow blinking)
2	PS Init low	******** (fast blinking)
3	RGPIO(1), when RGPIO Enabled over FPGA	User Defined
4	--	OFF

D17 - USB HUB LED (Suspend)

Green

status

ON, no USB connected, OFF, USB connected

SFP D9

Red

status/user

Priority	Description	Blink sequencing
1	Power On Reset	******** (slow blinking)
2	PS Init low	******** (fast blinking)
3	RGPIO(2), when RGPIO Enabled over FPGA	User Defined
4	--	OFF

SFP D10

Green

status/user

Priority	Description	Blink sequencing
1	Power On Reset	******** (slow blinking)
2	PS Init low	******** (fast blinking)
3	RGPIO(3), when RGPIO Enabled over FPGA	User Defined
4	--	OFF

ETH J7

Yellow

status

Priority	Description	Blink sequencing
1	Power On Reset	******** (slow blinking)
2	PS Init low	******** (fast blinking)
3	ETH PHY LED	(not PHY_LED0)

ETH J7

Green/Orange

status

Priority	Description	Blink sequencing
1	Power On Reset	******** (slow blinking)
2	PS Init low	******** (fast blinking)
3	ETH PHY LED	(PHY_LED1)

D4

Green

status/user

Priority	Description	Blink sequencing
1	1.8V disabled, inter CPLD RGPIO is disabled	******** (fast blinking)
2	1.8V enabled, inter CPLD RGPIO is disabled	*****ooo
3	Power On Reset	****oooo
4	USB Reset	***ooooo
5	RGPIO(4), when RGPIO Enabled over FPGA	User Defined
6	all fine	*ooooooo

D5

Red

status/user

Priority	Description	Blink sequencing
1	1.8V disabled, inter CPLD RGPIO is disabled	******** (fast blinking)
2	1.8V enabled, inter CPLD RGPIO is disabled	*****ooo
3	Power On Reset	****oooo
4	PCie Reset	***ooooo
5	RGPIO(4), when RGPIO Enabled over FPGA	User Defined
6	all fine	*ooooooo

RGPIO

There are 3 RGPIO interfaces, one InterCPLD RGPIO, and one from every CPLD to SoC.

InterCPLD RGPIO handles:

Signal	Description
Reset Button (SW)	for monitoring only
PS POR	for monitoring only
PS ERR Stat	for monitoring only
PS ERR	for monitoring only
PS Init	for monitoring only
PCIe Reset	for monitoring only
USB Reset	for USB Reset and monitoring
Power On Reset	for Power On Reset and monitoring
inter FPGA	Data from Slave RGPIO to Master RGPIO (for test only)

Master CPLD-SoC RGPIO (accesseble via SoC):

Signal

Description

FPGA Read (23)

JTAG_SRST

FPGA Read (22)

JTAG_TRST

FPGA Read (21)

FMC_CLKDIR

FPGA Read (20)

SD_WP

FPGA Read (19)

unused 0

FPGA Read (18)

SW4

FPGA Read (17)

SW3

FPGA Read (16)

XMOD_G

FPGA Read (15 dt 13)

PHY LEDs

FPGA Read (12)

CAN_FAULT

FPGA Read (11 dt 8)

current RGPIO Mux

FPGA Read (7 dt 0)

Data depends on MUX:

0	Data(7dt0) from Slave CPLD-SoC RGPIO
1	POR Statistic
2	PS RST Statistic
3	PS POR Statistic
4	PS Init Statistic
5	PS ERR Statistic
6	PS ERR Stat Statistic
7	PCie RST Statistic
8	USB RST Statistic

FPGA Write (23 dt 12)

unused

FPGA Write (11 dt 8)

RGPIO Mux, see FPGA Read (7 dt 0) , when RGIO active

FPGA Write (7 dt 6)

unused

FPGA Write (5 dt 0)

Diverse LED controll(see LED description) , when RGIO active

Slave CPLD-SoC RGPIO (accesseble via SoC):

Signal	Description
FPGA Read (23)	PLL_LOL
FPGA Read (22)	PG_PLL
FPGA Read (21)	PG_PL
FPGA Read (20)	PWROK and pwrok_force_zero_n
FPGA Read (19)	fmc_sanity_check
FPGA Read (18)	POK_FMC
FPGA Read (17)	PG_GT_R
FPGA Read (16)	PG_GT_L
FPGA Read (15)	PG_PSGT
FPGA Read (14)	PG_FPD
FPGA Read (13)	PG_DDR
FPGA Read (12)	PG_LPD
FPGA Read (11 dt 8)	current Boot Mode
FPGA Read (7)	ERR_STAT
FPGA Read (6)	ERROR
FPGA Read (5)	SD_CD_B
FPGA Read (4)	SD_CD_S
FPGA Read (3)	unused const 1
FPGA Read (2)	XMOD_BTN
FPGA Read (1)	SW2
FPGA Read (0)	SW1
FPGA Write (23 dt 8)	unused
FPGA Write (7dt 0)	Readable over Master CPLD-SoC RGPIO, when RGIO active

Appx. A: Change History and Legal Notices

Revision Changes

Master

Slave

CPLD REV07 to REV08

add major and minor revision number to uart string
bugfix DP_EN inverted
reduce statistic cnt size to save resources for newer diamond version
add X6 as optional ETH Reset from SOM(over MIO24 from Slave CPLD)

CPLD REV06 to REV07

complete rework
add inter CPLD RGPIO
new LED debugging sequencing
simple UART output with Revision Number and some statistic on second XMOD

CPLD REV05 to REV06

BUGFIX: renamed SC19 to SC17
Connect FMC JTAG to XMOD2 JTAG
Connect PJTAG0 (MIO29..26) to JTAG Pin Header J30
Connect CAN to PL
RGPIO Pin changes

CPLD REV04 to REV05

SD WP
XMOD LED access over PL

Older Revision (PCB REV03) to CPLD REV04

Fix USB HUB Mode default state over RGPIO
Invert JLED2B over RGPIO

Older Revision (PCB REV02) to CPLD REV04

Add all functionality from older Revision (PCB REV03)

CPLD REV07 to REV08

PSON inverted
Add MIO24 as additional ETH reset from SoM, and use X6 to forward it to Master CPLD
remove unused aud_clk_c constrain

CPLD REV06 to REV07

complete rework
add variants (power up and SD)multi-functions for buttons
power on and power downs sequencing
- module complete disable on power down
- power on sequencing
- power down sequencing --> can be forced with power button (hold longer)
Soft PS or PS POR Reset on Reset button (hold longer for PS POR Reset)
add inter CPLD RGPIO
new SoC RGPIO Pinout
removed reboot for pcie initialization
new LED debugging sequencing
Disabled UART on power down state
bugfix WP pin for microSD slot
removed PCIe Reboot.

CPLD REV05 to REV06

LED Status changes of LED D2 D3 and HD_LED, XMOD LED
extended Power Management

CPLD REV04 to REV05

PS reboot via FSBL over MIO30 (need for proper PCI initialization on first power on without press Reset Button)
SD Boot from micoSD only if switch S5-1/-2 is selected to ON
RGPIO connection
Add SD WP to FPGA
Power, Rest Button debounced
direct LED access via MIO and PL

Older Revision (PCB REV03) to CPLD REV04

Bugfix: PCIe Reset Pin location.
Bugfix: Swapping HDLED and PWRLED location.
Bugfix: MEMS_CLKIN Pin location.
Add XMOD 1 LED

Older Revision (PCB REV02) to CPLD REV04

Add all functionality from older Revision (PCB REV03)

Document Change History

To get content of older revision got to "Change History" of this page and select older document revision number.

Page properties

hidden	true
id	Comments

Note this list must be only updated, if the document is online on public doc!
It's semi automatically, so do following
- Add new row below first
- Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description. --> this point is will be deleted on newer pdf export template
- Metadata is only used of compatibility of older exports

Date

Document Revision

CPLD Firmware Revision

Supported PCB Revision

Authors

Description

Firmware Release

Page info

infoType	Modified date
dateFormat	yyyy-MM-dd
type	Flat

Page info

infoType	Current version
prefix	v.
type	Flat

REV08

REV05

Page info

	modified-user
	modified-user

Document Style Update
REV08

2024-10-30

2019-05-06

v.13

REV07

REV03,REV04*

REV07 finished
*please write to Trenz Electronic support for PCB REV02

2019-05-06

All

Page info

	modified-users
	modified-users

Legal Notices

Include Page

	IN:Legal Notices
	IN:Legal Notices

Scroll Only

HTML
<style> .wiki-content .columnLayout .cell.aside { width: 0%; }</style>

HTML
<style> .wiki-content .columnLayout .cell.aside { width: 20%; }</style>

Scroll pdf ignore

Custom_fix_page_content

Trenz Electronic Documentation

Versions Compared

Old Version 14

New Version 15

Key

Overview

Feature Summary

Firmware Revision and supported PCB Revision

Product Specification

Port Description

Functional Description

JTAG

Power

Reset

JTAG

Boot Mode

PCIe

SD

UART SoC

UART (Debug)

CAN

USB

DisplayPort

SFP

I2C

ETH

LEDs

RGPIO

Appx. A: Change History and Legal Notices

Revision Changes

Document Change History

Legal Notices

Table of contents