Page History
...
- Vivado Design Suite - Xilinx Design Software with JTAG drivers and documentation
- Xilinx Download Area - All Xilinx Software, Device Models and Libraries
Additional Documentation
| Table of Contents |
|---|
Important Notes
| Warning |
|---|
| Do not change XMOD DIP-Switch settings on TEBF0808. Do not swap the XMOD adapters the one marked with green dot must be closer to the SoM |
...
| Note |
|---|
For all Starter Kit's shipped before 2017-06-21: Enclosure Power and HD LED was swapped on connector. See "Enclosure Power Button, Reset Button, HDD LED and Power LED" section for correct connection. |
Getting Started
Starter Kit is shipped with prebuilt Linux Example on SD. Newest version and sources are available on our download area: TE0808 Reference Designs
Connect main power and set power switch to on. See Main Power Enclosure Location
- Connect mini USB cable from XMOD with green dot to host PC. See XMODs Connection
- Insert SD-Card with pre-loaded content into SD-Card slot.
- Open Serial Console:
- COM Port: for correct number see device manager
- Speed:115200
- Press the Power on button on the enclosure. See Power Button, Reset Button, HDD LED and Power LED Enclosure Location
- Linux login:
- User Name:root
- Password:root
Starter Kit Basic
Main Power Enclosure Location
Power Button , Reset Button, HDD LED and Power LED Enclosure Location
Default DIP Switch Settings
| Warning |
|---|
| Do not change XMOD DIP-Switch settings on TEBF0808. Do not swap the XMOD adapters the one marked with green dot must be closer to the SoM |
...
For more information, see:TEBF0808, TEBF0808 Master CPLD and TEBF0808 Slave CPLD.
Starter Kit Status
- Section is currently not complete -
Main Power Switch is OFF
No Power on Starter Kit.
Identification: FANs do not work, all LEDs are off.
Main Power Switch is ON and Power Button is not pressed
Only some basics on TEBF0808 are powered on. This mode is used for CPLDs Firmware updates.
...
| BLUE Power LED on enclosure | ||
|---|---|---|
| Status/ User | Blink Sequence | Comment |
| Power | ******** (slow blink) | Indicate board is powered off. |
| RGPIO controlled | User Defined | RGPIO 14 and 15, if RGPIO is active. |
| MIO40 | User Defined | MIO40, if RGPIO is deactivated |
Main Power Switch is ON and Power Button is pressed first time
TE0808 will be powered on. System boots if boot mode is set correct and files are available.
...
| Red HD LED on enclosure | ||
|---|---|---|
| Status/ User | Blink Sequence | Comment |
| PS_INIT_B | ******** | Indicates the PS is not initialized after a power-on reset (POR). |
| PS_ERROR_OUT | *****ooo | The PS_ERROR_OUT signal is asserted for accidental loss of power, an error, or an exception in the PMU. |
| ERR_STAT | ****oooo | The PS_ERROR_STATUS indicates a secure lockdown state. Alternatively, it can be used by the PMU firmware to indicate system status. |
| RGPIO controlled | User Defined | RGPIO 16 and 17, if RGPIO is active |
| SC0 | User Defined | SC0 (PL IO), if RGPIO is deactivated |
Notes
Most LEDs are CPLD Firmware dependents, see TEBF0808 Master CPLD and TEBF0808 Slave CPLD
SI5345 NVM Programming
SI5345 NVM is not programmed on factory, so modified FSBL is needed to get running output CLKS.
It it possible to program NVM of the SI5345 2 times. With NVM configuration FSBL initialisation is not needed.
NVM can be programmed with Clock Builder Pro Field Programmer connected to connector J17. General documentation to do this are available on Application notes - Si5345
Starter Kit Cable Connection
Starter Kit will be shipped with all cable connected.
ATX Power
Module
FMC FAN
XMODs
Enclosure USB
Enclosure FAN1 and HDAUDIO
Enclosure Power Button , Reset Button, HDD LED and Power LED
Support
- For support, please go to http://forum.trenz-electronic.de/ or contact support@trenz-electronic.de
Overview
Content Tools