Versions Compared

Old Version 13

changes.mady.by.user Ali Naseri

Saved on

compared with

New Version 14

changes.mady.by.user Ali Naseri

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

The TEB0729 Carrier Board's Board-to-Board Connectors (B2B) have the same pin-assignment as the mounted Zynq SoM due to its hermaphroditic structure. By this connectors, the MIO- and PL-IO-bank's pins and further interfaces of the Zynq SoM can be accessed. A large quantity of these I/O's are also usable as  as LVDS-pairs. The connectors provide also VCCIO voltages to operate the I/O's properly.

...

B2B ConnectorInterfacesCount of IO'sNotes
JB1User IO24 single ended-User IO
48 single ended or 24 differential-
JB2

User IO

54 single ended-
User IO10 single ended or 5 differential-
I²C2-
SD IO7-
UART2-
USB2.06-
2x 10/100-BaseT Ethernet14-
GbE MDI and SGMII14-
JTAG4-

...

VG96 ConnectorControl Signals and InterfacesCount of IO'sNotes
J8User IO24 single ended-User IO
48 single ended or 24 differential-
J9

User IO

54 single ended-
User IO10 single ended or 5 differential-
'NRST_IN', 'NRST_OUT', pins J9-A29, J9-B302SoM reset signals 1)
'BOARD_STAT', pins J9-B321-
'BOOT_MODE1', 'BOOT_MODE2', pins J9-C31, J9-C322Binary bootmode code of SoM
I²C, pins J9-A30, J9-A312I²C1 interface of module
GbE SGMII4SGMII interface of on-module GbE PHY

...

JB3 pinSignal Schematic Net NameB2BNote
C (pin 4)TCKJB2-119 -
D (pin 8)TDOJB2-117 -
F (pin 10)TDIJB2-115 -
H (pin 12)TMSJB2-113 -
A (pin 3)USART0_TXJB2-96 -
B (pin 7)USART0_RXJB2-94 -
E (pin 9)BOARD_STATJB2-112also connected to VG96 connector pin J9-B32
G (pin 11)NRST_IN 2)JB2-89also connected to VG96 connector pin J9-A29

...

DIP-switches S2Signal Schematic Net NameFunctionNote
S2-1JTAGSEL

Select Zynq chip or SC CPLD programming of mounted SoM:

OFF:  Zynq chip programming.device in JTAG chain
ON:    SC CPLD programmingin JTAG chain

Refer also to the TE0729 SC CPLD documentation for detailed information about JTAG update.
S2-2BOOT_MODE1Select first bit of boot mode codeRefer to TE0729 TRM and SC CPLD documentation for detailed information about boot modes.
S2-3BOOT_MODE2Select second bit boot mode code
S2-4xxnot used

...

VCCIO
vs. Voltage Levels		VCCIO_13VCCIO_33Note
1.8VJ7:pins 1-2J6: pins 1-2-
2.5VJ7: pins 3-4J6: pins 3-4-
3.3VJ7: pins 5-6J6: pins 5-6-

Table 16: VCCIO jumper settings.

...

Module Connector (B2B) DesignatorVCC / VCCIODirectionPinsNotes
JB1

VIN33

Out

Pin 1, 2, 3, 4, 5, 6

3.3V module supply voltage
VCCIO_13OutPin 101, 102PL IO-bank VCCIO
VCCIO_33OutPin 29, 30PL IO-bank VCCIO
3.3VInPin 65, 66voltage output from module
JB2

1.8V

In

Pin 49

voltage output from module
2.5VInPin 13voltage output from module
USB-VBUSOutPin 107USB Host supply voltage
VBAT_INOutPin 118RTC buffer voltage

Table 19: Power pin description of B2B Module Connector.

...

Jumper / Header DesignatorVCC / VCCIODirectionPinsNotes
J6VCCIO_33OutPin 2, 4, 6-
1.8VIn5-
2.5VIn3-
3.3VIn1-
J7

VCCIO_13

OutPin 2, 4, 6-
1.8VIn5-
2.5VIn3-
3.3VIn1-

...

Main Power Jack and Pins DesignatorVCC / VCCIODirectionPinsNotes
J125VINIn

-

-
J95VINInPin A1, A2'5VIN' power supply to the Carrier Board as alternative to J12
J2VBAT_INInPin 1Attention: Pin 2 connected to ground. VBAT_IN voltage on this pin cause short-circuit.

...

Peripheral Socket DesignatorVCC / VCCIODirectionPinsNotes
J10 / J11USB-VBUSOutPin 1USB2.0 Type A socket / Micro USB2.0 B socket
J1VIN33OutPin 4MikroSD Card socket VDD

Table 22: Power pin description of peripheral connector.

...

XMOD Header DesignatorVCC / VCCIODirectionPinsNotes
JB33.3V-Pin 5not connected
VIOOutPin 6connected to VIN33

Table 23: Power pin description of XMOD/JTAG Connector.

Board to Board Connectors

...

Order
number

Samtec NumberTypeMated HeightData sheetComment
-BTE-060-01-L-D-A-K-TRModule connector5 mmhttp://suddendocs.samtec.com/catalog_english/bte.pdfStandard connector
used on module
-BSE-060-01-L-D-A-TRBaseboard connector5 mmhttp://suddendocs.samtec.com/catalog_english/bse.pdfStandard connector
used on board

Table 24: B2B Connectors.

Variants Currently In Production

...

Variants Currently In Production

 Module Variant

Operating Temperature

USB SocketTemperature Range
TEB0729-02-A-40°C to +125°CUSB2.0 Type A socket fittedIndustrial
TEB0729-02-B-40°C to +125°CMicro USB2.0 B socket fittedIndustrial

Table 2425: Module variants.

Technical Specifications

...

Parameter

MinMax

Units

Reference Document

5VIN supply voltage

 -0.3 7

V

MP5010A, EN6347QI data sheet

Storage temperature

 -65

150

°C

-

Table 2526: Module absolute maximum ratings.

...

ParameterMinMaxUnitsReference Document
5VIN supply voltage 4.755.25 VUSB2.0 specification concerning 'VBUS' voltage
Operating temperature -40125°C-

Table 2627: Module recommended operating conditions.

...

Hardware Revision History

DateRevision

Notes

PCNSchematic Change NotesDocumentation LinkNote
-

01

First Production Release

 --TEB0729-01
--02
  • Second Production Release
  • HW-Modification since 22.08.2017
  • Refer to Changes list in Schematic
-TEB0729-02HW-Modification since 22.08.2017

Table 27Table 28: Module hardware revision history.

...

Date

Revision

Contributors

Description

Page info
modified-date
modified-date
dateFormatyyyy-MM-dd



Ali Naseriinitial document

Table 2829: Document change history.

...