Page History
...
- Barrel jack for 5V power supply
- 2x RJ45 10/100-BaseT Ethernet MagJack with 2 integrated LEDs
- 1x RJ45 Gigabit Ethernet MagJack with 2 integrated LEDs.
- 2x Configuration EEPROM's, connected to SoM's I²C interface
- XMOD compatible header to connect the TE0790 USB2.0 adapter board
- JTAG and UART interface over XMOD header
- MicroSD Card socket, can be used to boot system
- Micro-USB socket connected to Zynq module (device, host or OTG modesUSB2.0 socket (Option: USB Type A or Micro USB2.0 B)
- 4-bit DIP switch for SoM configuration (SoM's JTAG access and Bootmode)
- VG96 connector soldering-pads J8 for access to SoM's PL-IO-bank-pins, usable as LVDS-pairs
- VG96 connector soldering-pads J9 for access to further interfaces and IO's of the SoM
- 1 x user LED (red) routed to SoM IO-pin
- 1 x user push-button routed to SoM (Reset function at standard configuration)
- Pin headers to set PL-IO-bank's VCCIO
- Pin header for supplying SoM's VBAT voltage
- Footprint for optional USB2.0 Type A socket
- with jumper
Additional assembly options are available for cost or performance optimization upon request.
...
- 5V barrel jack, J12
- RJ-45 Gigabit Ethernet MegJack, J3
- RJ-45 10/100-BaseT Ethernet MegJack, J4
- RJ-45 10/100-BaseT Ethernet MegJack, J5
- VG96 connector placeholder, J9
- XMOD (TE0790) header, JB3
- 2-pin header for VBAT-IN supply-voltage, J2
- 2x6 pin header for setting VCCIO_33, J6
- 2x6 pin header for setting VCCIO_13, J7
- MicroSD Card socket, J1
- Red LED, D1
- Push Button, S1
- Micro USB2.0 B Receptacle (optional USB2.0 Type A socket)
- VG96 connector placeholder, J8
- B2B Connector, JB1
- B2B Connector, JB2
- 4-bit DIP-switch, S2
...
The TEB0729 Carrier Board is equipped with a Micro USB2.0 B (receptacle) socket J11 with board-revision TEB0729-02B, USB2.0 Type A socket is fitted on board-revision TEB0729-02A.
The differential data signals of the USB2.0 socket J11 are routed to the B2B connector JB2, where they can be accessed by the USB2.0 transceiver of the mounted SoM. The Micro USB USB2.0 connector can be used for Device mode, OTG Mode or Host Modes. For USB Host mode, the Carrier Board is additionally equipped with an USB load a power distribution switch U3 to provide the USB USB2.0 interface with the USB supply voltage USB-VBUS with nominal value of 5V. The Carrier Board provides the footprints J10 to equip the board with an USB2.0 Type A socket as an option ( OTG mode is not available with USB2.0 Type A socket).
Following table gives an overview of the USB2.0 interface signals:
...
| DIP-switches S2 | Signal Schematic Net Name | Function | Note | |
|---|---|---|---|---|
| S2-1 | JTAGSEL | Select Zynq chip or SC CPLD programming of mounted SoM: OFF: Zynq chip programming. | Refer also to the TE0729 SC CPLD TRM documentation for detailed information about JTAG update. | |
| S2-2 | BOOT_MODE1 | Select first bit of boot mode code | Refer to TE0729 TRM and SC CPLD | TRMdocumentation for detailed information about boot modes. |
| S2-3 | BOOT_MODE2 | Select second bit boot mode code | - | |
| S2-4 | x | x | not used |
Table 13: DIP-Switch S2 SoM configuration settings.
...
| Peripheral Socket Designator | VCC / VCCIO | Direction | Pins | Notes | |||||
|---|---|---|---|---|---|---|---|---|---|
| J10 / J11 | USB-VBUS | Out | Pin 1 | USB2.0 Type A socket | J11 | USB-VBUS | Out | Pin 1 | / Micro USB2.0 B socket |
| J1 | VIN33 | Out | Pin 4 | MikroSD Card socket VDD |
...
| XMOD Header Designator | VCC / VCCIO | Direction | Pins | Notes |
|---|---|---|---|---|
| JB3 | 3.3V | - | Pin 5 | not connected |
| VIO | InOut | Pin 6 | connected to VIN33 |
Table 21: Power pin description of XMOD/JTAG Connector.
...
| Date | Revision | Notes | PCN | Documentation Link |
|---|---|---|---|---|
| - | 01Prototypes | First Production Release | - | TEB0729-01 |
| - | 02First | Second Production Release | - | TEB0729-02 |
Table 25: Module hardware revision history.
...
Overview
Content Tools