Page History

Custom_table_size_100

Page properties

hidden	true
id	Comments

Design Name always "TE Series Name" + optional CPLD Name + "CPLD"

Date	Version	Changes	Author
2023-02-07	2.2	added column 'Firmware release' in 'Document Change History' table changed template revision from list to table	ma
-	2.1	Fix problem with pdf export and side scroll bar	-
-	2.0	add fix table of content add table size as macro removed page initial creator	-

Note

title	disclaimer

Because of incompatibility reasons with some customer carrier carriers the current CPLD Firmware revision REV02 and REV02.1 are obsolete only for testing purposes and we recommend to use the old REV01.
For cpld firmware REV01 - download and documentation please follow:
https://shop.trenz-electronic.de/en/Download/?path=Trenz_Electronic/Modules_and_Module_Carriers/8.5x8.5/TE0782/REV02/Firmware/archive

Overview

Firmware for PCB CPLD with designator U14. CPLD Device in Chain: LCMX02-1200HC

Feature Summary

Power Management
Reset Management
Boot Mode
LED
I2C
UART

Firmware Revision and supported PCB Revision

See Document Change History

Product Specification

Port Description

Name / opt. VHD Name	Direction	Pin	Pullup/Down	Bank Voltage	Description
BM0/MIO5	out	47	None	LVCMOS33	Boot Mode Pin
BM2/MIO4	out	48	None	LVCMOS33	Boot Mode Pin
BM3/MIO2	out	49	None	LVCMOS33	Boot Mode Pin
BOOTMODE	in	99	UP	LVCMOS33	Boot Mode Pin from B2B / Used for UART as input to MIO9
CONFIGX	out	98	UP	LVCMOS33	MIO8 to B2B / Used for UART as output from MIO8
CPLD_GPIO0		12	-	-	/ currently_not_used
CPLD_GPIO1		11	-	-	/ currently_not_used
CPLD_GPIO2		10	-	-	/ currently_not_used
CPLD_GPIO3		9	-	-	/ currently_not_used
CPLD_GPIO4		8	-	-	/ currently_not_used
CPLD_GPIO5		7	-	-	/ currently_not_used
CPLD_IO		54	-	-	/ currently_not_used
DONE	in	34	UP	LVCMOS33	FPGA Done Pin
EN_1.0V_MGT / EN_1V0_MGT	out	20	None	LVCMOS33	Power control
EN_1.2V_MGT / EN_1V2_MGT	out	18	None	LVCMOS33	Power control
EN_1.8V	out	16	None	LVCMOS33	Power control
EN_1V	out	21	None	LVCMOS33	Power control
EN_3.3V	out	15	None	LVCMOS33	Power control
ETH1_RESET	out	53	None	LVCMOS18	ETH Reset
ETH1_RESET33	in	43	UP	LVCMOS33	ETH Reset from MIO7
I2C_SCL	in	58	None	LVCMOS18	I2C CLK / I2C CLK connected to module I2C interface
I2C_SDA	inout	57	None	LVCMOS18	I2C DATA/ I2C SDA connected to module I2C interface
INIT		36	-	-	/ currently_not_used
JTAGENB	in	82	None	LVCMOS33	Is used here to set bootmode JTAG(high) or QSPI(low)
LED1 / GLED	out	4	None	LVCMOS33	green LED D2
LED2 / RLED	out	3	None	LVCMOS33	red LED D1
M_TCK	in	91	None	LVCMOS33	CPLD JTAG B2B
M_TDI	in	94	None	LVCMOS33	CPLD JTAG B2B
M_TDO	out	95	None	LVCMOS33	CPLD JTAG B2B
M_TMS	in	90	None	LVCMOS33	CPLD JTAG B2B
MIO8	in	38	UP	LVCMOS33	used UART RS activity
MIO9	out	39	None	LVCMOS33	User IO, connected to BOOTMODE Pin on B2B
MMC_RST	out	40	None	LVCMOS33	eMMC Reset
N.C. / dummy		1	-	-	/ currently_not_used
N.C.		2	-	-	/ currently_not_used
N.C.		27	-	-	/ currently_not_used
N.C.		28	-	-	/ currently_not_used
N.C.		29	-	-	/ currently_not_used
N.C.		30	-	-	/ currently_not_used
N.C.		32	-	-	/ currently_not_used
N.C.		41	-	-	/ currently_not_used
N.C.		42	-	-	/ currently_not_used
N.C.		59	-	-	/ currently_not_used
N.C.		60	-	-	/ currently_not_used
N.C.		61	-	-	/ currently_not_used
N.C.		62	-	-	/ currently_not_used
N.C.		63	-	-	/ currently_not_used
N.C.		64	-	-	/ currently_not_used
N.C.		65	-	-	/ currently_not_used
N.C.		66	-	-	/ currently_not_used
N.C.		67	-	-	/ currently_not_used
N.C.		68	-	-	/ currently_not_used
N.C.		69	-	-	/ currently_not_used
N.C.		70	-	-	/ currently_not_used
N.C.		71	-	-	/ currently_not_used
N.C.		74	-	-	/ currently_not_used
N.C.		75	-	-	/ currently_not_used
N.C.		76	-	-	/ currently_not_used
N.C.		77	-	-	/ currently_not_used
N.C.		78	-	-	/ currently_not_used
N.C.		81	-	-	/ currently_not_used
N.C.		83	-	-	/ currently_not_used
N.C.		84	-	-	/ currently_not_used
N.C.		85	-	-	/ currently_not_used
N.C.		86	-	-	/ currently_not_used
N.C.		87	-	-	/ currently_not_used
N.C.		88	-	-	/ currently_not_used
N.C.		89	-	-	/ currently_not_used
N.C.		96	-	-	/ currently_not_used
OTG-RST	out	52	UP	LVCMOS18	OTG Rest
OTG-RST33	in	45	UP	LVCMOS33	OTG Reset from MIO0
PG_1.0V_MGT	in	19	UP	LVCMOS33	Power control
PG_1.2V_MGT	in	17	UP	LVCMOS33	Power control
PG_1.8V	in	14	UP	LVCMOS33	Power control
PG_1V	in	25	UP	LVCMOS33	Power control
PG_1V5	in	24	UP	LVCMOS33	Power control
PG_3.3V	in	13	UP	LVCMOS33	Power control
PROG_B		35	None	-	/ currently_not_used
PS_POR	out	37	None	LVCMOS33	PS_POR_B (Power On Reset)
PS_SRST	out	51	None	LVCMOS18	PS_SRST_B (PS Reset)
RESIN	in	97	UP	LVCMOS33	Reset from B2B
RTC_INT		31	-	-	/ currently_not_used

Functional Description

JTAG

Used only for Firmware Update. Zynq has dedicated JTAG connection.

Power

Power enables (EN_1V, EN_1V8, EN_3V3, EN_1V2_MGT, EN_1V0_MGT) are all enabled sequentially.
EN_1V → EN_1V8 → EN_3V3 → EN_1V0_MGT → EN_1V2_MGT

Power goods (PG_1V, PG_1V5, PG_1V8, PG_3V3, PG_1V2_MGT, PG_1V0_MGT) are used for System Reset and LED Monitoring.

Boot Mode

JTAG or QSPI.
Bootmode is read through JTAGENB signal (can be set by DIP switch on carrier).
Can also be changed through software I2C after linux has bootet. (command: i2cset -y 0 0x20 0x03 <0x02 or 0x00>)

Reset

PS_POR is triggered by soft_resetn when bootmode is changed by software (I2C interface) or main power failed

PS_SRST is triggered when user reset pressed (RESIN) or main power failed.

ETH1_RESET is triggered when ETH1_RESET33(e.g. by fsbl) or main power failed.

OTG_RST is triggered when ETH1_OTG_RST33(e.g. by fsbl) or main power failed.

MMC_RST is triggered when main power failed.

Info

title	main power failed

main power failed - is triggered when at least one of the Power Good signals of the DCDCs goes down.

UART

MIO8 is connected to CONFIGX. UART TX from FPGA to RX XMOD.

BOOTMODE is connected to MIO9. UART RX.

LED

Red LED D1

Blink sequence	Priority	Condition	Description
********	highest	RESIN = LOW (low active)	external reset "RESIN" is pressed
*******o			blink sequence not used
******oo			blink sequence not used
*****ooo		PG_1V or PG_1V5 or PG_1V8 or PG_3V3 is zero	One of the Power Good Signals of internal Voltages DCDCs LOW
****oooo			blink sequence not used
***ooooo			blink sequence not used
**oooooo		PG_1V2_MGT or PG_1V0_MGT is zero	One of the Power Good Signals of MGT Voltages DCDCs LOW
*ooooooo		DONE = '0'	FPGA not programmed, wrong Bootmode? Check JTAGENB signal. No design on QSPI Flash?
continuously ON	lowest	software controlled command: i2cset -y 0 0x20 0x05 <0x00 or 0x01>	If none of the above condition is met

Green LED D2

Blink sequence	Priority	Condition	Description
********	highest	PG_1V or PG_1V5 or PG_1V8 or PG_3V3 or PG_1V2_MGT or PG_1V0_MGT is zero	Power Good Signal of DCDCs deassertion occurred after power up. Look at content of power good register → i2cget -y 0 0x20 0x02
*******o			blink sequence not used
******oo			blink sequence not used
*****ooo			blink sequence not used
****oooo			blink sequence not used
***ooooo		bootmode was changed via I2C.	command: i2cset -y 0 0x20 0x03 <0x02 or 0x00>
**oooooo			blink sequence not used
*ooooooo			blink sequence not used
UART activity	lowest	LED = MIO8	If none of the above condition is met

I2C Interface

This subsystem provides 2 x 32-bit (8 x 8-bit) of general purpose parallel input and output (I/O) expansion for the I2C bus protocol. Address of this module is 0x20. This module contains eight 8-bit registers for reading and writing (GPIO_register_1[7:0] to GPIO_register_1[31:24] and GPIO_register_2[7:0] to GPIO_register_2[31:24]) separately with address 0x00 to 0x07. These registers can be accessed with I2C commands in linux console or with i2c functions in FSBL code. To access these registers the following commands in linux console can be used:

To see the i2c bus addresses :                                     i2cdetect -y -r 0

To read register of i2c to GPIO module:                            i2cget -y 0 0x20 <register address>

To write data in a register of i2c to GPIO module:                 i2cset -y 0 0x20 <register address> <data>

Expand

title	example, turn red LED D1 ON

All eight registers can be read, but only two of them can be written from the linux console.

I2C Register	permissions	address	function	I2C command
GPIO_register_1(7 downto 0)	readable	0x00	contains the CPLD Firmware Revision (not the PCB revision)	read: i2cget -y 0 0x20 0x00
GPIO_register_1(15 downto 8)	readable	0x01	contains the bootmode in bit 8 and bit 9. This register is read by the fsbl and printed in the console as the bootmode during power up
GPIO_register_1(23 downto 16)	readable	0x02	Bit 17 to 23 contain the DCDC power good signals and the DONE pin
GPIO_register_1(31 downto 24)	readable/writeable	0x03	Bit 24 and 25 contain the bootmode, JTAG(b 00) or QSPI(b 10)	write: i2cset -y 0 0x20 0x03 <0x02 or 0x00>
GPIO_register_2(7 downto 0)	readable	0x04	Bit 0 to 3 show the state of the reset signals PS_POR, PS_SRST, ETH1_RESET, OTG_RST
GPIO_register_2(15 downto 8)	readable/writeable	0x05	Bit 8 can be controlled to change the state of the red LED D1 if no other red LED condition is met	write: i2cset -y 0 0x20 0x05 <0x00 or 0x01>
GPIO_register_2(23 downto 16)	readable	0x06	not used
GPIO_register_2(31 downto 24)	readable	0x07	not used

Appx. A: Change History and Legal Notices

Revision Changes

Document Change History

To get content of older revision got to "Change History" of this page and select older document revision number.

Page properties

hidden	true
id	Comments

Note this list must be only updated, if the document is online on public doc!
It's semi automatically, so do following
- Add new row below first
- Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description. --> this point is will be deleted on newer pdf export template
- Metadata is only used of compatibility of older exports

Date

Document Revision

CPLD Firmware Revision

Supported PCB Revision

Authors

Description

Firmware release

Page info

	modified-date
	modified-date
dateFormat	yyyy-MM-dd

Page info

	current-version
	current-version
prefix	v.

REV02.1

Page info

	modified-user
	modified-user

JTAGENB functionality inverted - "0" -> QSPI; "1" -> JTAG

Revision 02.1, 18.06.2024 released

REV02

CPLD Firmware Update
LED blinking
Power Sequencing
I2C Interface to FPGA for status communication

Revision 02, 28.11.2023 released

2018-05-25

v.5

REV01

RE02

John

Hartfiel

typo correction
add UART description

13 Mar 2018

v.3

REV01

RE02

John Hartfiel

REV01 , Firmware released 2016-06-27

2018-03-12

v.1

Page info

	created-user
	created-user

Initial release

All

Page info

	modified-users
	modified-users

Legal Notices

Include Page

	IN:Legal Notices
	IN:Legal Notices

Scroll Only

HTML
<style> .wiki-content .columnLayout .cell.aside { width: 0%; }</style>

HTML
<style> .wiki-content .columnLayout .cell.aside { width: 20%; }</style>

Scroll pdf ignore

Custom_fix_page_content

Trenz Electronic Documentation

Versions Compared

Old Version 11

New Version Current

Key

Overview

Firmware Revision and supported PCB Revision

Product Specification

Port Description

Functional Description

JTAG

Power

Boot Mode

Reset

UART

LED

I2C Interface

Appx. A: Change History and Legal Notices

Revision Changes

Document Change History

Legal Notices

Table of contents