| Page properties |
|---|
|
In this section you must explain how to power on the board and run the Reference Design (test board) on the particular module. The main points must be mentioned are: |
| Scroll pdf ignore |
|---|
Table of Contents |
TEBF0808 with TE080x
Overview
Basic instructions to work with TEBF0808 and TE0808,TE0807 or TE0803.
| Info |
|---|
Functionality of buttons, DIP switches, LEDs depends on CPLD Firmware. Following description is only for newest firmware version, which is available on the download area |
| Scroll Title |
|---|
| anchor | Figure_Overview |
|---|
| title | Board Overview |
|---|
|
| Scroll Ignore |
|---|
| scroll-pdf | true |
|---|
| scroll-office | true |
|---|
| scroll-chm | true |
|---|
| scroll-docbook | true |
|---|
| scroll-eclipsehelp | true |
|---|
| scroll-epub | true |
|---|
| scroll-html | true |
|---|
| | draw.io Diagram |
|---|
| border | false |
|---|
| viewerToolbar | true |
|---|
| |
|---|
| fitWindow | false |
|---|
| diagramDisplayName | |
|---|
| lbox | true |
|---|
| revision | 6 |
|---|
| diagramName | TEBF0808_getting_started_overview |
|---|
| simpleViewer | true |
|---|
| width | |
|---|
| links | auto |
|---|
| tbstyle | top |
|---|
| diagramWidth | 641 |
|---|
|
|
| Scroll Only |
|---|
|
|
| Number | Note |
| Letter | Note |
|---|
| 1 | S2- Reset Button |
| A | P1 - PMOD 3.3V I2C Bus |
|---|
| 2 | D7 - LED D7 Red (Usage: status) || D6 - LED Green (Usage: status) |
| B | J9 - Audio Enclosure |
|---|
| 3 | S1 - Reset Button |
| C | J26 - FAN1 12V |
|---|
| 4 | J25 - Power Jack J25, 2.1mm (optional 12V power input) |
| D | J17 - I2C (for optional module PLL access) |
|---|
| 5 | S5 - DIP Switch for Boot Mode and FMCVADJ |
| E | J6/15 - Firefly - GTH |
|---|
| 6 | J10 - Enclosure Pin header(Reset and Power Button, HD LED (Usage: status/user) and Power LED (Usage: status/user)) |
| F | J31 - SATA |
|---|
| 7 | S4 - DIP Switch for CPLD access and power control |
| G | J21/22 - Firefly - loopback only |
|---|
| 8 | J12 - XMOD with green dot for Module JTAG and UART, XMOD LED D4 Red used for status information |
| H | P3 - PMOD 3.3V I2C Bus |
|---|
| 9 | J28 - XMOD for CPLD,FMC JTAG and Firmware ID over UART(need CPLD Firmware 7 or newer) , XMOD LED D4 Red used for status information |
| I | J34 - I2C Firefly |
|---|
| 10 | FPGA Done LED (location varies slightly on different module series ) |
| J | J35 - FAN2 12V |
|---|
| 11 | J20 - ATX Power Connector (Main 12V and 5V Power supply), recommended power supply connector |
| K | J11 - PCIe (1x) |
|---|
| 12 | D1 - SFP LED Red (Usage: status/user) |
| L | B1 - Battery holder CR1220 |
|---|
| 13 | D8 - SFP LED Green (Usage: status/user) |
| M | J30 - PJTAG |
|---|
| 14 | D9 - SFP LED Red (Usage: status/user) |
| N | J29 - CAN (same as J24) |
|---|
| 15 | D10 - SFP LED Green (Usage: status/user) |
| O | J5 - FMC HPC |
|---|
| 16 | J7 - ETH LED Yellow (Usage: status) |
| P | J19 - FAN3 5V |
|---|
| 17 | J7 - ETH LED Green/Orange (Usage: status) |
| Q | J24 - CAN (same as J29) |
|---|
| 18 | D4 - LED Green (Usage: status/user) || D5 - LED Red (Usage: status/user) |
| R | J27 - SD |
|---|
|
|
| S | J8 - USB 3.0 (2x) Enclosure |
|---|
|
|
| T | J14 - SFP (2x) |
|---|
|
|
| U | J7 - USB 3.0 (2x), ETH (1x) |
|---|
|
|
| V | J13 - Displayport (1x) |
|---|
|
|
| W | P2 - PMOD 3.3V FPG IOs |
|---|
|
|
| W(b) | Bottom side: J16 - microSD |
|---|
Power supply
| Page properties |
|---|
|
The input power supply must be mentioned. Add Link to overview picture with connector label.
|
Recommended power supply unit is PC power supply unit over connector J20 (Overview - 12)
- DIP S4-4 can be switched OFF with this power supply configuration (CPLD firmware depended)
Optional single 12V power supply over J25 (Overview - 12)
- DIP S4-4 must be switched ON with this power supply
| Page properties |
|---|
|
Explain all DIP switches functionality. Add Link to overview picture with connector label.
|
| Scroll Title |
|---|
| anchor | Table_DIP_1 |
|---|
| title | DIP Switches S4 |
|---|
|
| Scroll Table Layout |
|---|
| orientation | portrait |
|---|
| sortDirection | ASC |
|---|
| repeatTableHeaders | default |
|---|
| sortByColumn | 1 |
|---|
| sortEnabled | false |
|---|
| cellHighlighting | true |
|---|
|
| Overview 7 | Default | Description |
|---|
| S4-1 | OFF | SoC PUDC, ON (low - internal FPGA pull ups enabled), OFF (high - internal FPGA pull ups disabled) | | S4-2 | OFF | N.C. | | S4-3 | OFF | JTAGEN ON (CPLD access), OFF (FMC access) | | S4-4 | ON | Enable on board 5V permanently |
|
| Scroll Title |
|---|
| anchor | Table_DIP_2 |
|---|
| title | DIP Switches S5 (CPLD Firmware depended) |
|---|
|
| Scroll Table Layout |
|---|
| orientation | portrait |
|---|
| sortDirection | ASC |
|---|
| repeatTableHeaders | default |
|---|
| sortByColumn | 1 |
|---|
| sortEnabled | false |
|---|
| cellHighlighting | true |
|---|
|
| Overview 5 | Default | Description |
|---|
| S5-1 | ON | - ON(1), ON(2) - Default, boot from SD/microSD or SPI Flash if no SD is detected
- OFF(1), ON(2) - Boot from eMMC
- ON(1), OFF(2) - Boot mode PJTAG0
- OFF(1), ON(2) -Boot mode main JTAG
| | S5-2 | ON | | S5-3 | OFF | User Input over RGPIO | | S5-4 | OFF | VADJ OFF(1.8V), ON(1.2V) |
|
Jumpers
| Page properties |
|---|
|
Explain all Jumpers functionality and connection. Add Link to overview picture with connector label. |
| Scroll Title |
|---|
| anchor | Table_Jumpers |
|---|
| title | Jumpers |
|---|
|
| Scroll Table Layout |
|---|
| orientation | portrait |
|---|
| sortDirection | ASC |
|---|
| repeatTableHeaders | default |
|---|
| sortByColumn | 1 |
|---|
| sortEnabled | false |
|---|
| cellHighlighting | true |
|---|
|
|
LEDs
| Page properties |
|---|
|
Explain all user LEDs functionality and connections. Add Link to overview picture with connector label.
|
| Scroll Title |
|---|
| anchor | Table_LED |
|---|
| title | Carrier LEDs |
|---|
|
| Scroll Table Layout |
|---|
| orientation | portrait |
|---|
| sortDirection | ASC |
|---|
| repeatTableHeaders | default |
|---|
| sortByColumn | 1 |
|---|
| sortEnabled | false |
|---|
| cellHighlighting | true |
|---|
|
|
Furthermore, there are two user LEDs on module TE0728.
| Scroll Title |
|---|
| anchor | Table_LED |
|---|
| title | Module LEDs |
|---|
|
| Scroll Table Layout |
|---|
| orientation | portrait |
|---|
| sortDirection | ASC |
|---|
| repeatTableHeaders | default |
|---|
| sortByColumn | 1 |
|---|
| sortEnabled | false |
|---|
| cellHighlighting | true |
|---|
|
| Designator | Color | Connected to | Note |
|---|
| D1 | Red | DONE signal (PS Configuration Bank 503) | This LED goes ON when power has been applied to the module and stays ON until MPSoC's programmable logic is configured properly. |
|
JTAG/UART
| Page properties |
|---|
|
Explain JTAG or UART connection . Add Link to overview picture with connector label.
|
SoC JTAG and UART connections are available through XMOD JTAG adapter with the green dot on J12. For more information refer to TE0790.
DIP Switch on the XMOD JTAG adapter must be set like the following table.
| Scroll Title |
|---|
| anchor | Table_XMOD_JTAG |
|---|
| title | XMOD JTAG DIP Switch. Attention: Never changes the default setting |
|---|
|
| Scroll Table Layout |
|---|
| orientation | portrait |
|---|
| sortDirection | ASC |
|---|
| repeatTableHeaders | default |
|---|
| sortByColumn | 1 |
|---|
| sortEnabled | false |
|---|
| cellHighlighting | true |
|---|
|
| XMOD DIP Switch | Setting |
|---|
| 1 | ON | | 2 | OFF | | 3 | OFF | | 4 | OFF |
|
CPLD Firmware Update
Boot Mode
Reference Designs
| Page properties |
|---|
|
In this Section you must refer to the Reference Design (Test board) for the particular module. For Example: TE0728 Reference Designs |
Notes
| Page properties |
|---|
|
In this Section you must refer to the Resources Page for the particular module. For Example: TE0728 Resources |
Module and Carrier are also as starter kit available: