Table of Contents
TEBF0808 with TE080x
Overview
Basic instructions to work with TEBF0808 and TE0808,TE0807 or TE0803.
Functionality of buttons, DIP switches, LEDs depends on CPLD Firmware. Following description is only for newest firmware version, which is available on the download area
Board Overview
| Number | Note | Letter | Note | |
|---|---|---|---|---|
| 1 | S2- Reset Button | A | P1 - PMOD 3.3V I2C Bus | |
| 2 | D7 - LED D7 Red (Usage: status) || D6 - LED Green (Usage: status) | B | J9 - Audio Enclosure | |
| 3 | S1 - Reset Button | C | J26 - FAN1 12V | |
| 4 | J25 - Power Jack J25, 2.1mm (optional 12V power input) | D | J17 - I2C (for optional module PLL access) | |
| 5 | S5 - DIP Switch for Boot Mode and FMCVADJ | E | J6/15 - Firefly - GTH | |
| 6 | J10 - Enclosure Pin header(Reset and Power Button, HD LED (Usage: status/user) and Power LED (Usage: status/user)) | F | J31 - SATA | |
| 7 | S4 - DIP Switch for CPLD access and power control | G | J21/22 - Firefly - loopback only | |
| 8 | J12 - XMOD with green dot for Module JTAG and UART, XMOD LED D4 Red used for status information | H | P3 - PMOD 3.3V I2C Bus | |
| 9 | J28 - XMOD for CPLD,FMC JTAG and Firmware ID over UART(need CPLD Firmware 7 or newer) , XMOD LED D4 Red used for status information | I | J34 - I2C Firefly | |
| 10 | FPGA Done LED (location varies slightly on different module series ) | J | J35 - FAN2 12V | |
| 11 | J20 - ATX Power Connector (Main 12V and 5V Power supply), recommended power supply connector | K | J11 - PCIe (1x) | |
| 12 | D1 - SFP LED Red (Usage: status/user) | L | B1 - Battery holder CR1220 | |
| 13 | D8 - SFP LED Green (Usage: status/user) | M | J30 - PJTAG | |
| 14 | D9 - SFP LED Red (Usage: status/user) | N | J29 - CAN (same as J24) | |
| 15 | D10 - SFP LED Green (Usage: status/user) | O | J5 - FMC HPC | |
| 16 | J7 - ETH LED Yellow (Usage: status) | P | J19 - FAN3 5V | |
| 17 | J7 - ETH LED Green/Orange (Usage: status) | Q | J24 - CAN (same as J29) | |
| 18 | D4 - LED Green (Usage: status/user) || D5 - LED Red (Usage: status/user) | R | J27 - SD | |
| S | J8 - USB 3.0 (2x) Enclosure | |||
| T | J14 - SFP (2x) | |||
| U | J7 - USB 3.0 (2x), ETH (1x) | |||
| V | J13 - Displayport (1x) | |||
| W | P2 - PMOD 3.3V FPG IOs | |||
| W(b) | Bottom side: J16 - microSD |
Power supply
Recommended power supply unit is PC power supply unit over connector J20 (Overview - 12)
- DIP S4-4 can be switched OFF with this power supply configuration (CPLD firmware depended)
Optional single 12V power supply over J25 (Overview - 12)
- DIP S4-4 must be switched ON with this power supply
DIP-Switches and Push Buttons
| Overview 7 | Default | Description |
|---|---|---|
| S4-1 | OFF | SoC PUDC, ON (low - internal FPGA pull ups enabled), OFF (high - internal FPGA pull ups disabled) |
| S4-2 | OFF | N.C. |
| S4-3 | OFF | JTAGEN ON (CPLD access), OFF (FMC access) |
| S4-4 | ON | Enable on board 5V permanently |
DIP Switches S4
| Overview 5 | Default | Description |
|---|---|---|
| S5-1 | ON |
|
| S5-2 | ON | |
| S5-3 | OFF | User Input over RGPIO |
| S5-4 | OFF | VADJ OFF(1.8V), ON(1.2V) |
DIP Switches S5 (CPLD Firmware depended)
Jumpers
Jumpers
LEDs
Carrier LEDs
Furthermore, there are two user LEDs on module TE0728.
| Designator | Color | Connected to | Note |
|---|---|---|---|
| D1 | Red | DONE signal (PS Configuration Bank 503) | This LED goes ON when power has been applied to the module and stays ON until MPSoC's programmable logic is configured properly. |
Module LEDs
JTAG/UART
SoC JTAG and UART connections are available through XMOD JTAG adapter with the green dot on J12. For more information refer to TE0790.
DIP Switch on the XMOD JTAG adapter must be set like the following table.
| XMOD DIP Switch | Setting |
|---|---|
| 1 | ON |
| 2 | OFF |
| 3 | OFF |
| 4 | OFF |
XMOD JTAG DIP Switch. Attention: Never changes the default setting
CPLD Firmware Update
Boot Mode
Reference Designs
Notes
Module and Carrier are also as starter kit available:
Overview
Content Tools