Page History

...

...

...

TE Scripts are only needed to generate the vivado project, all other additional steps are optional and can also executed by Xilinx Vivado/SDK GUI.  For currently Scripts limitations on Win and Linux OS see: Project Delivery Currently limitations of functionality 

1. _create_win_setup.cmd/_create_linux_setup.sh and follow instructions on shell:
   
2. Press 0 and enter for minimum setup
3. (optional Win OS) Generate Virtual Drive or use short directory  for the reference design (for example x:\<design name>)
4. Create Project
   
   1. Select correct device and Xilinx install path on "design_basic_settings.cmd" and create Vivado project with "vivado_create_project_guimode.cmd"
      Note: Select correct one, see TE Board Part Files
                Important: Use Board Part Files, which ends with *_tebf0808
5. Create HDF and export to prebuilt folder
   
   1. Run on Vivado TCL: TE::hw_build_design -export_prebuilt
      Note: Script generate design and export files into \prebuilt\hardware\<short dir>. Use GUI is the same, except file export to prebuilt folder
6. Create Linux (bl31.elf, uboot.elf and image.ub) with exported HDF
   
   1. HDF is exported to "prebuilt\hardware\<short name>"
      Note: HW Export from Vivado GUI create another path as default workspace.
   2. Create Linux images on VM, see PetaLinux KICKstart
      1. Use TE Template from /os/petalinux
         Note: run init_config.sh before you start petalinux config. This will set correct temporary path variable.
7. Add Linux files (bl31.elf, uboot.elf and image.ub) to prebuilt folder
   
   1. "prebuilt\os\petalinux\default" or "prebuilt\os\petalinux\<short name>"
      Notes: Scripts select "prebuilt\os\petalinux\<short name>", if exist, otherwise "prebuilt\os\petalinux\default"
8. Generate Programming Files with HSI/SDK
   
   1. Run on Vivado TCL: TE::sw_run_hsi
      Note: Scripts generate applications and bootable files, which are defined in "sw_lib\apps_list.csv"
   2. (alternative) Start SDK with Vivado GUI or start with TE Scripts on Vivado TCL: TE::sw_run_sdk
      Note: See SDK Projects

...

1. Prepare HW like described on section Programming 46042671
2. Connect UART USB (JTAG XMOD)
3. Select SD Card as Boot Mode (or QSPI - depending on step 1)
   Note: See TRM of the Carrier, which is used.
4. (Optional) Insert PCIe Card (detection depends on Linux driver. Only some basic drivers are installed)
5. (Optional) Connect Sata Disc
6. (Optional) Connect DisplayPort Monitor (List of usable Monitors: https://www.xilinx.com/support/answers/68671.html)
7. (Optional) Connect Network Cable
8. Power On PCB
   Note: 1. ZynqMP Boot ROM loads PMU Firmware and  FSBL from SD into OCM, 2. FSBL loads ATF(bl31.elf) and U-boot from SD/QSPI into DDR, 3. U-boot load Linux from SD into DDR.

...

# system controller ip
set_property PACKAGE_PIN A13 [get_ports BASE_sc10_io]
set_property PACKAGE_PIN B13 [get_ports BASE_sc11]
set_property PACKAGE_PIN A14 [get_ports BASE_sc12]
set_property PACKAGE_PIN B14 [get_ports BASE_sc13]
set_property PACKAGE_PIN F13 [get_ports BASE_sc14]
set_property PACKAGE_PIN G13 [get_ports BASE_sc15]
set_property PACKAGE_PIN D15 [get_ports BASE_sc5]
set_property PACKAGE_PIN H13 [get_ports BASE_sc6]
set_property PACKAGE_PIN H14 [get_ports BASE_sc7]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc5]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc6]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc7]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc10_io]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc11]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc12]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc13]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc14]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc15]

# Audio Codec
#LRCLK          J3:49 
#BCLK            J3:51 
#DAC_SDATA    J3:53 
#ADC_SDATA    J3:55 
set_property PACKAGE_PIN L13 [get_ports LRCLK ]
set_property PACKAGE_PIN L14 [get_ports BCLK ]
set_property PACKAGE_PIN E15 [get_ports DAC_SDATA ]
set_property PACKAGE_PIN F15 [get_ports ADC_SDATA ]
set_property IOSTANDARD LVCMOS18 [get_ports LRCLK ]
set_property IOSTANDARD LVCMOS18 [get_ports BCLK ]
set_property IOSTANDARD LVCMOS18 [get_ports DAC_SDATA ]
set_property IOSTANDARD LVCMOS18 [get_ports ADC_SDATA ]
#LED
#LED_HD SC0 J3:31
set_property PACKAGE_PIN G14 [get_ports {LED_HD[0]}]
set_property IOSTANDARD LVCMOS18 [get_ports {LED_HD[0]}]
#LED_XMOD SC17 J3:48 
set_property PACKAGE_PIN B15 [get_ports {LED_XMOD2[0]}]
set_property IOSTANDARD LVCMOS18 [get_ports {LED_XMOD2[0]}]

# CAN
#CAN RX SC19 J3:52 B26_L11_P
#CAN TX SC18 J3:50 B26_L11_N
#CAN S  SC16 J3:46 B26_L1_N

set_property PACKAGE_PIN A15 [get_ports CAN_0_S ]
set_property IOSTANDARD LVCMOS18 [get_ports CAN_0_S ]
set_property PACKAGE_PIN K14 [get_ports CAN_0_rx ]
set_property IOSTANDARD LVCMOS18 [get_ports CAN_0_rx ]
set_property PACKAGE_PIN J14 [get_ports CAN_0_tx ]
set_property IOSTANDARD LVCMOS18 [get_ports CAN_0_tx ]

...

Legal Notices