Versions Compared

Old Version 2

changes.mady.by.user John Hartfiel

Saved on

compared with

New Version Current

changes.mady.by.user John Hartfiel

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

There are 3 different Firmware variants available:

  1. (Default): SCM_0xAxA_default.jed/SCS_0xAxA_default.jed
  2. (optional): SCM_0xBxB_powerdown_disabled.jed/SCS_0xBxB_powerdown_disabled.jed - Power down Sequencing is disabled (See Note Power Management).
  3. (optional): SCM_0xCxC_msdboot_disabled.jed/SCS_0xCxC_msdboot_disabled.jed - CD Pin of MicroSD will not influence boot Mode (mircoSD can be used as Filesystem and system Boots from QSPI)

...

Name / opt. VHD NameDirectionPinBank PowerDescriptionCPLD
C_T1
243V3SB / currently_not_used U17
C_T2
263V3SB / currently_not_used U17
C_T3
253V3SB / currently_not_used U17
C_TCKin1313V3SBJTAG J28 (XMOD2) / FMC JTAG
U17
C_TDIin1363V3SBJTAG J28 (XMOD2) / FMC JTAG
U17
C_TDO1 / C_TDOout1373V3SBJTAG J28 (XMOD2) / FMC JTAG
U17
C_TMSin1303V3SBJTAG J28 (XMOD2) / FMC JTAG
U17
CAN_FAULT
1063V3SBCANU17
CAN_RXin1073V3SBCANU17
CAN_Sout1053V3SBCANU17
CAN_TXout1043V3SBCANU17
CLK_125MHz / PHY_CLKin701.8V / currently_not_used U17
CON_NTRST / JTAG_TRSTin1173V3SBJTAG, Connector J30U17
CON_RTCK / JTAG_RTCKout1253V3SBJTAG, Connector J30U17
CON_sRST / JTAG_SRSTin1273V3SBJTAG, Connector J30U17
CON_TCK / JTAG_TCKin1223V3SBJTAG, Connector J30U17
CON_TDI / JTAG_TDIin1193V3SBJTAG, Connector J30U17
CON_TDO / JTAG_TDOout1263V3SBJTAG, Connector J30U17
CON_TMS / JTAG_TMSin1213V3SBJTAG, Connector J30U17
DIR_T1
233V3SB / currently_not_used U17
DIR_T2
283V3SB / currently_not_used U17
DIR_T3
273V3SB / currently_not_used U17
DP_AUX_DE / DP_DEout923V3SBDisplay PortU17
DP_AUX_RX / DP_RXin913V3SBDisplay PortU17
DP_AUX_TX / DP_TXout933V3SBDisplay PortU17
DP_ENout773V3SBDisplay PortU17
DP_TX_HPD / DP_HPDin943V3SBDisplay PortU17
ETH_RSTout621.8VETH ResetU17
EX_IO1
1123V3SB / currently_not_used U17
EX_IO2
1133V3SB / currently_not_used U17
EX_IO3
1143V3SB / currently_not_used U17
EX_IO4
1153V3SB / currently_not_used U17
F2_ENout193V3SB / currently_not_used FAN2U17
F2PWMout203V3SB / currently_not_used FAN2U17
F2SENSEin213V3SB / currently_not_used FAN2U17
FMC_CLK_DIR / FMC_CLKDIRin733V3SBFMCU17
FMC_TCKout953V3SBFMCU17
FMC_TDIout963V3SBFMCU17
FMC_TDOin973V3SBFMCU17
FMC_TMSout983V3SBFMCU17
FMC_VID0out1393V3SBFMCU17
FMC_VID1out1403V3SBFMCU17
FMC_VID2out1413V3SBFMCU17
GND
843V3SBREV03 unconnected / currently_not_usedU17
HDIO_SC10 / SC10out601.8VFPGA / DP_RX or 'Z'U17
HDIO_SC11 / SC11in591.8VFPGA / DP_DEU17
HDIO_SC12 / SC12out581.8VFPGA / DP_HPDU17
HDIO_SC13 / SC13out571.8VFPGA / RGPIO TXU17
HDIO_SC14 / SC14in561.8VFPGA / RGPIO RXU17
HDIO_SC15 / SC15in551.8VFPGA / RGPIO CLKU17
HDIO_SC16 / SC16in541.8VFPGA / CAN_SU17
HDIO_SC17 / SC17in521.8VFPGA / XMOD LED U17
HDIO_SC18 / SC18in681.8VFPGA / CAN_TXU17
HDIO_SC19 / SC19out691.8VFPGA / CAN_RXU17
I2C_RSTout611.8VI2CU17
JTAGENB
1203V3SBexternal Pin for CPLD Firmware Update U17
LED_1A / JLED1out1093V3SBUSB3.0 LED JellowU17
LED_2A / JLED2Aout1113V3SBUSB3.0 LED Green/OrangeU17
LED_2B / JLED2Bout1103V3SBUSB3.0 LED Green/OrangeU17
MIO26out411.8VMIO / PJTAGU17
MIO27out401.8VMIO / PJTAGU17
MIO28in391.8VMIO / PJTAGU17
MIO29out381.8VMIO / PJTAGU17
OCLK_EN / OSC_ENout743V3SBProgrammable Oscillator U45U17
PHY_CONFIGout651.8VETH PHYU17
PHY_LED0in671.8VETH PHYU17
PHY_LED1in863V3SBETH PHYU17
PHY_LED2in853V3SBETH PHYU17
SC_CLK0 / CLK0in763V3SB/ currently_not_usedU17
SC_CLK1 / CLK1in753V3SB/ currently_not_usedU17
SC_IO0 / X0out501.8VMTS dummyU17
SC_IO1 / X1in491.8Vinternal cpld RGPIO CLKU17
SC_IO2 / X2out481.8Vinternal cpld RGPIO TXU17
SC_IO3 / X3in471.8Vinternal cpld RGPIO RXU17
SC_IO4 / X4out451.8VSD WP to slave cpldU17
SC_IO5 / X5in441.8VSTM dummyU17
SC_IO6 / X6out431.8V/ currently_not_usedU17
SC_IO7 / X7out421.8V/ currently_not_usedU17
SC_IO8 / X8in223V3SBinternal cpld RGPIO available(1.8V on)U17
SC_SCL / SCLin143V3SBI2C Mux U27 / currently_not_usedU17
SC_SDA / SDAin133V3SBI2C Mux U27 / currently_not_usedU17
SC2_SW3 / SW3in63V3SBDIP-Switch S5-3U17
SC2_SW4 / SW4in53V3SBDIP-Switch S5-4U17
SD_WPin1003V3SBMMC SDWPU17
SFP_LED1 / SFP_LED0out813V3SBSFPU17
SFP_LED2 / SFP_LED1out823V3SBSFPU17
SFP_LED3 / SFP_LED2out783V3SBSFPU17
SFP_LED4 / SFP_LED3out833V3SBSFPU17
SFP1_LOS
323V3SBSFP / currently_not_used U17
SFP1_TX_DISout333V3SBSFPU17
SFP2_LOS
353V3SBSFP / currently_not_used U17
SFP2_TX_DISout343V3SBSFPU17
STAT_LED0 / LED0out993V3SBLED D4 Green U17
STAT_LED1 / LED1out1283V3SBLED D1 Red U17
USB0_RST / USB_TRST
711.8VUSB (U9) PHY ResetU17
USBH_LED_G3
113V3SBUSB Hub (U4)  / currently_not_used U17
USBH_LED_G4
123V3SBUSB Hub (U4)  / currently_not_used U17
USBH_LED_SS1
93V3SBUSB Hub (U4)  / currently_not_used U17
USBH_LED_SS2
1333V3SBUSB Hub (U4)  / currently_not_used U17
USBH_LED_SS3
1323V3SBUSB Hub (U4)  / currently_not_used U17
USBH_LED_SS4
1383V3SBUSB Hub (U4)  / currently_not_used U17
USBH_MODE0out1423V3SBUSB Hub (U4)U17
USBH_MODE1out1433V3SBUSB Hub (U4)U17
USBH_RSTout103V3SBUSB Hub (U4)U17
XMOD1_A / XMOD_TXDout33V3SBJ28 (XMOD 2 UART)U17
XMOD1_B / XMOD_RXDin23V3SBJ28 (XMOD 2 UART)U17
XMOD1_E / XMOD_Eout43V3SBJ28 (XMOD 2 LED)U17
XMOD1_G / XMOD_Gout13V3SBJ28 (XMOD 2 Button)U17
1.8V_EN / EN_1V8out1063V3SBEnable 1.8V PowerU39
5V_EN / EN_5Vout1153V3SBEnable 5V Power, can be permanently enabled by S4-4U39
C_TCK
1313V3SBJTAG J28 (XMOD2)  / currently_not_used U39
C_TDOout1373V3SBJTAG J28 (XMOD2)
U39
C_TDO1 / C_TDIin1363V3SBJTAG J28 (XMOD2) U39
C_TMS
1303V3SBJTAG J28 (XMOD2)  / currently_not_used U39
CLK_A / AUD_CLKout11.8VAUDIO U3 CLKU39
CLK_CPLD / MEMS_CLKINin1283V3SBU25 24,576MHzU39
DONEin671.8VPS DoneU39
EN_DDRout863V3SBEnable Module DDR PowerU39
EN_FMC / FMC_ENout1043V3SBFMCU39
EN_FPDout813V3SBEnable Module PS FPD PowerU39
EN_GT_Lout773V3SBEnable Module GT PowerU39
EN_GT_Rout933V3SBEnable Module GT PowerU39
EN_LPDout843V3SBEnable Module  PS LPD PowerU39
EN_PLout953V3SBEnable Module PL PowerU39
EN_PLL_PWRout783V3SBEnable Module SI5345 PowerU39
EN_PSGT / EN_PSGTRout753V3SBEnable Module PS GT PowerU39
ERR_OUT / ERRORin701.8VModule PS Error Out / StatusU39
ERR_STATUS / ERR_STATin691.8VModule PS Error StatusU39
F1PWMout1213V3SBFAN1U39
F1SENSEin1253V3SBFAN1U39
FAN_FMC_EN / FMC_FAN_EN
1323V3SBFMC FANU39
FMC_PG_C2Mout1413V3SBFMC PGU39
HD_LED_N / HDLED_Nout1123V3SBJ10 HD LEDU39
HD_LED_P / HDLED_Pout1103V3SBJ10 HD LEDU39
HDIO_SC0 / SC0in321.8VFPGA IO /  forward to HD_LED_P / HDLED_PU39
HDIO_SC1 / SC1in331.8V/ currently_not_used U39
HDIO_SC2 / SC2in341.8V/ currently_not_used U39
HDIO_SC3
351.8V / currently_not_used U39
HDIO_SC4
251.8V / currently_not_used U39
HDIO_SC5 / SC5out261.8VFPGA IO / RGPIOU39
HDIO_SC6 / SC6in271.8VFPGA IO / RGPIO CLKU39
HDIO_SC7 / SC7in281.8V.FPGA IO / RGPIOU39
I2C_SCL / SCLin501.8VI2C / currently_not_usedU39
I2C_SDA / SDAin521.8VI2C / currently_not_usedU39
INIT_B / INITin681.8VModule PS Init_BU39
JTAGENB
1203V3SBexternal Pin for CPLD Firmware UpdateU39
LP_GOOD / PG_LPDin833V3SBModule LP Power GoodU39
MIO24
381.8VMIO  / currently_not_used U39
MIO25
391.8VMIO  / currently_not_used U39
MIO30in481.8VMIO / USB ResetU39
MIO31in491.8VMIO / PCIe ResetU39
MIO32
401.8VMIO / currently_not_used U39
MIO33
411.8VMIO  / currently_not_used U39
MIO34
421.8VMIO  / currently_not_used U39
MIO35
431.8VMIO  / currently_not_used U39
MIO36
441.8VMIO  / currently_not_used U39
MIO37
451.8VMIO  / currently_not_used U39
MIO40in541.8VMIOU39
MIO41
551.8VMIO  / currently_not_used U39
MIO42out601.8VMIOU39
MIO43in611.8VMIOU39
MIO44
471.8VMIOU39
MOD_ENout1193V3SBEnable Main Module Power 3.3VU39
MODE0out61.8VModule Boot ModeU39
MODE1out91.8VModule Boot ModeU39
MODE2out101.8VModule Boot ModeU39
MODE3out111.8VModule Boot ModeU39
MR / MRESETnout923V3SBModule PS Power ResetU39
PCI_SFP_ENout763V3SBSFPU39
PER_ENout1173V3SBEnable 3.3V powerU39
PERST / PERSTnout1393V3SBPCIE ResetnU39
PG_DDRin913V3SBModule Power GoodU39
PG_FPDin853V3SBModule Power GoodU39
PG_GT_Lin963V3SBModule Power GoodU39
PG_GT_Rin943V3SBModule Power GoodU39
PG_PLin823V3SBModule Power GoodU39
PG_PLL_1V8 / PG_PLLin733V3SBModule Power GoodU39
PG_PSGTin743V3SBModule Power GoodU39
PLL_LOLn / PLL_LOLin581.8VModule PLL / currently_not_usedU39
PLL_RST / PLL_RSTnout561.8VModule PLL ResetU39
PLL_SEL0out571.8VModule PLLU39
PLL_SEL1out591.8VModule PLLU39
POK_1V8in1073V3SBCarrier Power GoodU39
POK_FMCin993V3SBFMC Power GoodU39
PROG_BOUT711.8VModule PS_PROG_BU39
PSONout1053V3SBATX J20 PS_ON_NU39
PWR_BTNin1133V3SBPower Button S1 or J10U39
PWRLED_N / LED_Nout1113V3SBJ10 PWRU39
PWRLED_P / LED_Pout1093V3SBJ10 PWRU39
PWROKin1003V3SBATX J20 PWROKU39
RST_BTNin1143V3SBReset Button S2 or J10U39
S_1
1273V3SBBEEPER / currently_not_used U39
SC_IO0 / X0in121.8VMTS dummyU39
SC_IO1 / X1out131.8Vinternal cpld RGPIO CLKU39
SC_IO2 / X2in141.8Vinternal cpld RGPIO RXU39
SC_IO3 / X3out201.8Vinternal cpld RGPIO TXU39
SC_IO4 / X4in211.8VMMC SD WP from masterU39
SC_IO5 / X5out221.8VSTM dummyU39
SC_IO6 / X6in231.8V / currently_not_used U39
SC_IO7 / X7in241.8V / currently_not_used U39
SC_IO8 / X8out1263V3SBinternal cpld RGPIO available(1.8V on)U39
SC2_SW1 / SW1in1333V3SBS5-1 / Boot Mode SelectionU39
SC2_SW2 / SW2in1383V3SBS5-2 / Boot Mode SelectionU39
SD_A_ENout1403V3SBMicro SDU39
SD_B_ENout1223V3SBMMC SDU39
SD_CD / SD_CD_OUTout651.8VSD Card detect to FPGAU39
SD_CD_Bin1433V3SBMMC SD CDU39
SD_CD_Sin1423V3SBMicro SD CDU39
SEL_SD / SD_SELout621.8VSD select (Mirco or MMC)U39
SRST_B / SRSTnout191.8VModule PS_SRST_BU39
STAT_LED2 / LED2out983V3SBLED D6 GreenU39
STAT_LED3 / LED3out973V3SBLED D7 RedU39
XMOD2_A / XMOD_TXDout51.8VJ12 (XMOD 1 UART)U39
XMOD2_B / XMOD_RXDin41.8VJ12 (XMOD 1 UART)U39
XMOD2_E / XMOD_LEDout31.8VJ12 (XMOD 1 LED)U39
XMOD2_G / XMOD_BTNin21.8VJ12 (XMOD 1 Button)U39

...

SignalDescription
ETH_RSTPower On Reset
PHY_CONFIGconst 1

LEDs

LEDs are handled on both CPLDs.

They used different Blink Sequence to indicate all state:

FAN

ETH Reset is handled on Master CPLD

SignalDescription
FAN1
  • EN: enabled with power
  • PWM: const 1
FAN2
  • PWM: const 1
  • EN: const 1
FMC FAN
  • EN enabled with power
  • PWM: via "LM96163CISD/NOPB"
    • CPLD includes simple I2C master which set fan speed to 0x03 after power on.
    • User can controll FAN via SoC Modul:
      • I2C Bus:15 (U27-5 SC_SDA/SDL)
      • I2C device Address: 0x4C
      • Example full speed via Starterkit Reference design :i2cset -y -r 15 0x4c 0x4c 0x3F

LEDs

LEDs are handled on both CPLDs.

They used different Blink Sequence to indicate all state:

******** (slow blinking)~0,7 Hzcontinuous blinking, ******** (slow blinking)~0,7 Hzcontinuous blinking, like SFP LEDs or Enclosure HD LED when board is powered down
******** (fast blinking)~5,8 Hzcontinuous blinking, like D6 LED or Enclosure Power LED when board is powered down
*****ooo~0,7 Hz, duty cycle 5/85 times fast blink with a break
****oooo~0,7 Hz, duty cycle 4/84 times fast blink with a break
***ooooo~0,7 Hz, duty cycle 3/83 times fast blink with a break
**oooooo~0,7 Hz, duty cycle 2/82 times fast blink with a break
*ooooooo~0,7 Hz, duty cycle 1/81 times fast blink with a break
ON---LED ON
OFF---LED OFF

...

DesignatorColorUsageDescription
D7Redstatus


PriorityDescriptionBlink sequencing
1PS POR Reset pressed long time (or whole system is powered off)ON
2PS Soft Reset pressed short timeOFF
3SD Boot*ooooooo
4QSPI Boot**oooooo
5eMMC Boot***ooooo
6PJTAG Boot****oooo
7JTAG Boot*****ooo
8Error******** (fast blinking)


D6Greenstatus


PriorityDescriptionBlink sequencing
1Power OFF******** (fast blinking)
2PG_LPD low*****ooo
3PG_FPD low****oooo
4PG_PL low***ooooo
5PG_DDR low or PG_PSGT low or PG_PLL low or PG_GT_L low or PG_GT_R low**oooooo
6POK_1V8 low or POK_FMC low or perihpery_pg low or (Main Power State Machine Ready and FMC Sanity check low)*ooooooo
7Main Power State Machine ReadyOFF
8ERROR some power failed, see XMOD LEDsON


J10 Power LEDBlue (symbol light bulb)status/user


PriorityDescriptionBlink sequencing
1power button pressed long time forced power down******** (fast blinking)
2

Main Power State Machine Idle and Power of State is off

******** (slow blinking)
3power button pressed short time power to power on/off*****ooo
4PS reset button pressed long time****oooo
5PS reset button pressed short time***ooooo
6power down sequencing is running**oooooo
7whole system hold into reset*ooooooo
8MIO40User Defined


J10 HD LED

Red (symbol drive)

status/user


PriorityDescriptionBlink sequencing
1PS Init is low******** (fast blinking)
2PS Error High*****ooo
3PS Error Status High****oooo
4SOC Done  low***ooooo
5SC0User Defined


XMOD1 D4Redstatus


PriorityXMOD ButtonDescriptionBlink sequencing
1Pressedpower button pressed long time forced power down******** (fast blinking)
2PressedMain Power State Machine Idle and Power of State is power down
sequencing		*****ooo
3Pressed

PS reset button pressed

****oooo
4PressedPower button pressed short time power on/off***ooooo
5PressedPower of State is power down sequencing**oooooo
6PressedSystem hold into reset*ooooooo
7PressedPS Init lowON
1UnpressedProblem with other CPLD, FMC is disabled******** (fast blinking)
2UnpressedMain Power State Machine Wait Ready ON/OFF*****ooo
3UnpressedMain Power State Machine 3.3V and VADJ ON/OFF****oooo
4Unpressedpower not ready (power reset)**oooooo
5Unpressedzynq reset*ooooooo
7UnpressedPS Init lowON
xPressed/Unpressedall fineOFF


XMOD2 D4Redstatus/user


PriorityDescriptionBlink sequencing
1Power On Reset********  (slow blinking)
2PS Init low******** (fast blinking)
3SC17User Defined


SFP D1Redstatus/user


PriorityDescriptionBlink sequencing
1Power On Reset******** (slow blinking)
2PS Init low******** (fast blinking)
3RGPIO(0), when RGPIO Enabled over FPGAUser Defined
4--OFF


SFP D8Greenstatus/user


PriorityDescriptionBlink sequencing
1Power On Reset******** (slow blinking)
2PS Init low******** (fast blinking)
3RGPIO(1), when RGPIO Enabled over FPGAUser Defined
4--OFF


D17 - USB HUB LED (Suspend)GreenstatusON, no USB connected, OFF, USB connected
SFP D9Redstatus/user


PriorityDescriptionBlink sequencing
1Power On Reset******** (slow blinking)
2PS Init low******** (fast blinking)
3RGPIO(2), when RGPIO Enabled over FPGAUser Defined
4--OFF


SFP D10Greenstatus/user


PriorityDescriptionBlink sequencing
1Power On Reset******** (slow blinking)
2PS Init low******** (fast blinking)
3RGPIO(3), when RGPIO Enabled over FPGAUser Defined
4--OFF


ETH J7Yellowstatus


PriorityDescriptionBlink sequencing
1Power On Reset******** (slow blinking)
2PS Init low******** (fast blinking)
3ETH PHY LED(not PHY_LED0)


ETH J7Green/Orangestatus


PriorityDescriptionBlink sequencing
1Power On Reset******** (slow blinking)
2PS Init low******** (fast blinking)
3ETH PHY LED(PHY_LED1)


D4Greenstatus/user


PriorityDescriptionBlink sequencing
11.8V disabled, inter CPLD RGPIO is disabled******** (fast blinking)
21.8V enabled, inter CPLD RGPIO is disabled*****ooo
3Power On Reset****oooo
4USB Reset***ooooo
5RGPIO(4), when RGPIO Enabled over FPGAUser Defined
6all fine*ooooooo


D5Redstatus/user


PriorityDescriptionBlink sequencing
11.8V disabled, inter CPLD RGPIO is disabled******** (fast blinking)
21.8V enabled, inter CPLD RGPIO is disabled*****ooo
3Power On Reset****oooo
4PCie Reset***ooooo
5RGPIO(4), when RGPIO Enabled over FPGAUser Defined
6all fine*ooooooo



RGPIO 

There are 3 RGPIO interfaces, one InterCPLD RGPIO, and one from every CPLD to SoC.

...

SignalDescription
FPGA Read (23)JTAG_SRST
FPGA Read (22)JTAG_TRST
FPGA Read (21)FMC_CLKDIR
FPGA Read (20)SD_WP
FPGA Read (19)unused 0
FPGA Read (18)SW4
FPGA Read (17)SW3
FPGA Read (16)XMOD_G
FPGA Read (15 dt 13)PHY LEDs
FPGA Read (12)CAN_FAULT
FPGA Read (11 dt 8)current RGPIO Mux
FPGA Read (7 dt 0)

Data depends on MUX:

0Data(7dt0) from Slave CPLD-SoC RGPIO
1POR Statistic
2PS RST Statistic
3PS POR Statistic
4PS Init Statistic
5PS ERR Statistic
6PS ERR Stat Statistic
7PCie RST Statistic
8USB RST Statistic


FPGA Write (23 dt 12)unused
FPGA Write (11 dt 8)RGPIO Mux, see FPGA Read (7 dt 0) , when RGIO active
FPGA Write (7 dt 6)unused
FPGA Write (5 dt 0)Diverse LED controll(see LED description) , when RGIO active

...

Revision Changes

TEBF0808 versionCPLD REV01 to TEBF0808 version

Copy from TEBF0808 SCB0808 REV07(dev)

MasterSlave

CPLD REV02 to REV01

  • add enable FAN2(F2*) with const 1 PWM
  • add I2C Master and FMC FAN activation(only slow speed, customer can control via FPGA and I2C)

CPLD REV02 to REV01

  • DISABLE_ATX_PWROK default 0

CPLD REV01 to TEBF0808 version(Copy from TEBF0808 SCB0808 REV07(dev))

  • disable DP-HPD pullup
  • changed CPLD string name
  • counter deep for status register (otherwhise new version of lattice mapping tool has problems)

CPLD REV01 to TEBF0808 version(Copy from TEBF0808 SCB0808 REV07(dev)

)

  • Add Parameter to disable PWOK usage(for 12V only usage, CPLD can't detect which power supply is used on PCB REV01 and POWK will be forced to low, in case ATX is not connected)
  • PSON inverted

Document Change History

To get content of older revision  got to "Change History"  of this page and select older document revision number.

Page properties
hiddentrue
idComments
  • Note this list must be only updated, if the document is online on public doc!
  • It's semi automatically, so do following

    • Add new row below first

    • Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description. --> this point is will be deleted on newer pdf export template

    • Metadata is only used of compatibility of older exports


REV01*
DateDocument RevisionCPLD Firmware RevisionSupported PCB RevisionAuthorsDescription

Page info
modified-date
modified-date
dateFormatyyyy-MM-dd

Page info
infoTypeCurrent current-versioncurrent- version
prefixv.

REV01

typeFlat




REV02REV02

Page info
modified-user
modified-user

  • Update new content
  • REV02 finished (Firmware released on 2023-06-14,SC-PGM-TEBF0818-02_SCBF0818-02_20230614.zip)

2021-09-21

v.2

REV01REV01*


  • Initial release (copy from TEBF0808 CPLD Firmware REV07  )
  • REV01 finished (Firmware released on 2021-09-21)
  • *special Firmware for TEBF0818-01 only

All

Page info
modified-users
modified-users


...