Page History
Overview
The Trenz Electronic TE0725 is a low cost small-sized FPGA module integrating a Xilinx Artix-7 (15-100T) and 32 MByte Flash memory for configuration and operation.
The 2 x 50 pin headers with a 2,54mm standard pitch are perfect for breadboard or low cost dual layer PCB . design.
Main Components
Top View | Bottom View |
- Xilinx Artix-7 FPGA, U1
- 32 MByte Flash Memory, U7
- Enpirion EN6347 4A PowerSoC DC-DC Step Down Converter, U10
- Enpirion EN5311 1A PowerSoC Synchronous Buck Regulator With Integrated Inductor, U11
- POF Tranceiver Placeholder, U8
- 50-pin placeholder for breadboard connection, J1
- 50-pin placeholder for breadboard connection, J2
- JTAG/UART connector, JB1
- Green LED D2(SYSLED) and Red LED D3(DONE)
- 16K x 8 (128 Kbit) Serial EEPROM, U2
- Ultralow Supply-Current Voltage Monitor With Optional Watchdog, U9
Key Features
Xilinx Artix-7 XC7A35T (A15 to A100T)
commercial temperature grade (industrial on requestCommercial Temperature Grade (Industrial on Request)
32 MByte Flash memoryMemory
2 x 50 pin headers Pin Headers with 2,54mm pitchPitch, ideal Ideal for breadboard useBreadboard Use
- 87 IO's (42 + 42 + 3)
- 100 MHz System Clock
- I2C EEPROM
3.3V single supply with on board voltage regulatorsSingle Power Supply with On-Board Voltage Regulators
Size 73 x 35 mm
JTAG/Uart connector UART Connector
2 LEDsLED's
- optional Optional HyperRAM (8 to 32 MByte)
- optional Optional POF Fiber Optical Adapter (125, 250 or 1000MBit/s)
...
...
...
Initial Delivery State
...
Signals, Interfaces and Pins
IO Banks
Bank | VCCIO | B2B I/O | Notes |
---|---|---|---|
0 | 3.3V | 0 | JTAG |
14 | 3.3V | 0 (3) | 3 I/O in XMOD-JTAG - for use as UART |
15 | 1.8V | 0 | used for optional hyper RAM |
16 | 2.5V | 0 | used for optional optical fiber |
34 | User select | 42 | 0R resistor option to select 3.3V |
35 | User select | 42 | 0R resistor option to select 3.3V |
LED's
LED | Color | FPGA | |
---|---|---|---|
D2 | green | M16 | |
D3 | red | DONE | Active Low |
POF Transceiver
...
Bitrate MB/s | Notes | |
---|---|---|
AFBR-59F2Z | 250 |
JTAG Interface
JTAG access to the Xilinx Artix-7 device is provided through connector JB1.
Connectors
All connectors are are for 100mil headers, all connector locations are in 100 mil grid.
...
TCK | JB1: 4 |
TDO | JB1: 8 |
TDI | JB1: 10 |
TMS | JB1: 12 |
Connector JB1 (2 x 6 pin Header) is directly compatible to XMOD JTAG Adapter TE0790, this . This adapter can be inserted from top onto the TE0725, if JB1 is fitted with male pin header. Optionally JB1 can be fitted with pin header from bottom, in that case the JTAG cable connector must be on the base board.
...
When using XMOD-JTAG please check the switch settings on XMOD to be sure the power and I/O reference are supplied correctly. TE0790 can in some case be used to power up TE0725, this is however not recommended. TE0790-01 has not enough power for TE0725 (LED Blink may work, for larger designs the XMOD delivered power may be not sufficient).
Technical Specification
LED's
LED | Color | FPGA | |
---|---|---|---|
D2 | green | M16 | |
D3 | red | DONE | Active Low |
Connectors
All connectors are are for 100mil headers, all connector locations are in 100 mil grid.
LED | Color | FPGA | |
---|---|---|---|
D2 | green | M16 | |
D3 | red | DONE | Active Low |
Power and Power-On Sequence
For startup, a power supply with minimum current capability of 1A is recommended.
Power Supply
...
Single 3.3V Power supply required.
Power Consumption
FPGA | Design | Typical Power, 25C ambient |
---|---|---|
A35T | not configured | TBD |
A35T | LED Blinky | 170mW (typical) |
A100T | not configured | TBD |
Typical power consumption
Connectors
TBD - To Be Determined.
Technical Specification
...
Measurements and placement of the connectors and mounting holes. All 100 mil pin headers are in 100 mil grid, the M3 mounting holes are in 50 mil grid aligned to the centers of the 100mil headers. The module is symmetrical, turning it 180 degrees will keep all I/O and Power Pins in both 50 pin headers in compatible places.
Revision History
Hardware Revision History
Date | Revision | Notes | PCN | Documentation link |
---|---|---|---|---|
- | 01 | Prototypes | ||
- | 02 | First production release |
Hardware revision number is printed on the PCB board together with the module model number separated by the dash.
Document Change History
Date | Revision | Contributors | Description |
---|---|---|---|
2016-12-02 | Jan Kumann | Initial version |
Disclaimer
Include Page | ||||
---|---|---|---|---|
|