Page History
...
I/O signals connected to the FPGA's I/O banks and B2B connector:
Bank | Type | B2B Connector | I/O Signal Count | Voltage | Notes |
---|---|---|---|---|---|
0 | HR | - | - | 3.3V | Configuration bank |
12 | HR | JM2 | 50 I/O-pins 24 LVDS-pairs possible | User | HR-Banks support voltages from 1.2V to 3.3V standards. NOTE: BANK 12 IS NOT AVAILABLE ON THE K70T DEVICE. |
13 | HR | JM1 | 48 I/O-pins 24 LVDS-pairs possible | User | HR-Banks support voltages from 1.2V to 3.3V standards. |
14 | HR | JM1, JM3 | 8 I/O-pins, 4 I/O-pins (2 LVDS-pairs possible) | 3.3V | pins at B2B connector JM1, 3.3V IO-voltage. |
15 | HR | JM2 | 18 I/O-pins 9 LVDS-pairs possible | User | HR-Banks support voltages from 1.2V to 3.3V standards. |
16 | HR | JM1 | 16 I/O-pins 8 LVDS-pairs possible | User | HR-Banks support voltages from 1.2V to 3.3V standards. |
32 | HP | NC | - | - | Bank not used. |
33 | HP | NC | - | - | Bank not used. |
34 | HP | NC | - | - | Bank not used. |
Table 2: Voltage ranges and pin-outs of available logic banks of the FPGA.
...
Special purpose pins are connected to smaller System Controller CPLD and have following default configuration:
Pin Name | Mode | Function | Default Configuration | B2B Connector |
---|---|---|---|---|
PGOOD | Output | Power Good | Active high when all on-module power supplies are working properly. | JM1-30 |
RESIN | Input | Reset | Active low reset signal, drive low to keep the system in reset (FPGA pin PROG_B will be driven by CPLD). | JM2-18 |
JTAGMODE | Input | JTAG Select | Low for normal operation, high (3.3V) to programm the System Controller CPLD. | JM1-89 |
Table 4: Pin-description of System Controller CPLD
...
There are four LED's available on TE0741 SoM. Two status LED's (D3 and D4) and two user configurable LED's (D1 and D2).
LED | Color | Connected to | Description and Notes |
---|---|---|---|
D1 | green | LED2 | User configurable LED. |
D2 | red | LED1 | User configurable LED. |
D3 | green | DONE | Reflects inverted DONE signal, ON when FPGA is not configured, OFF as soon as PL is configured. This LED will not operate if the the 3.3V power rail is not available. After FPGA configuration the user can use USRACCESSE2 to control Done LED. |
D4 | green | C_LED | Connected to the system controller indicating status of the module: Steadily lit: RESIN pin is kept low. Blinking fast (0.1s on/off): Power sequencing fault (PG_ALL = 0). Blinking at medium speed (0.5s on/off): Power sequencing has completed but the FPGA is not configured (PG_ALL = 1, DONE = 0). Blinking slow (1s on/off): FPGA is configured and board is ready (PG_ALL = 1, DONE = 1). It is also possible to program the System Controller CPLD to connect this LED to FPGA pin named XIO. |
Table 5: Description of the on board LED's.
...
Variants Currently In Production
Designator / Module Variant | U1 | U15 |
---|---|---|
TE0741-070-2CF | XC7K70T-2FBG676C | - |
TE0741-160-2CF | XC7K160T-2FBG676C | - |
TE0741-325-2CF | XC7K325T-2FBG676C | EN63A0QI |
TE0741-410-2CF | XC7K325T-2FBG676C | EN63A0QI |
TE0741-070-2IF | XC7K70T-2FBG676I | - |
TE0741-160-2IF | XC7K160T-2FBG676I | - |
TE0741-325-2IF | XC7K325T-2FBG676I | EN63A0QI |
TE0741-160-2C1 | XC7K160T-2FFG676C | - |
Table 11: Differences between variants of Module TE0741.
Technical Specifications
Absolute Maximum Ratings
Parameter | Min | Max | Units | Notes |
---|---|---|---|---|
VIN supply voltage | -0.3 | 6.5 | V | - |
3.3VIN supply voltage | -0.1 | 3.6 | V | - |
PL IO bank supply voltage for HR I/O Banks (VCCO) | -0.5 | 3.6 | V | - |
I/O input voltage for HR I/O banks | -0.4 | VCCO_X+0.55 | V | - |
GT receiver (RXP/RXN) and transmitter (TXP/TXN) | -0.5 | 1.26 | V | Xilinx datasheet DS182 |
Voltage on module JTAG pins | -0.5 | VCCO_0+0.45 | V | VCCO_0 is 3.3V nominal. |
Storage temperature | -55 | +125 | °C | - |
Table 12: Absolute maximum ratings.
...
Recommended Operation Conditions
Parameter | Min | Max | Units | Notes | Reference Document |
---|---|---|---|---|---|
VIN supply voltage | 2.4 | 5.5 | V | - | EP53F8QI data sheet |
3.3VIN supply voltage | 3.135 | 3.465 | V | 3,3V ± 5% | - |
PL I/O bank supply voltage for HR I/O banks (VCCO) | 1.14 | 3.465 | V | - | Xilinx datasheet DS182 |
I/O input voltage for HR I/O Banks | - 0.20 | VCCO+0.2 | V | - | Xilinx datasheet DS182 |
GT receiver (RXP/RXN) and transmitter (TXP/TXN) | (*) | (*) | - | - | Xilinx datasheet DS182 |
Voltage on Module JTAG pins | 3.135 | 3. |
465 | V | - |
- |
Table 13: Recommended operation conditions.
...
Hardware Revision History
Date | Revision | Notes | PCN | Documentation link |
---|---|---|---|---|
01 | First production release | |||
02 |
|
Hardware revision number is printed on the PCB board together with the module model number separated by the dash.
...