Page History
...
Additional assembly options are available for cost or performance optimization upon request.
Block Diagram
Put your block diagram here...
Scroll Title | ||||
---|---|---|---|---|
| ||||
...
Scroll Title | ||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||||||||||||
|
- SFP+ 2x1 cage with integrated LED light pipes, J9
- DisplayPort connector, J12
- USB3 A 2x , RJ45 1x (stacked), J13
- FMC connector (FMC B), J4
- FMC B cooling fan, M2
- FMC connector (FMC C), J8
- FMC C cooling fan, M3
- FMC connector (FMC D), J7
- FMC D cooling fan, M4
- FMC connector (FMC E), J6
- FMC E cooling fan, M5
- I²C programming header of on-board PLL clock generator U17, J22
- 4-Wire PWM fan connector, J23
- Main Power Jack 24V, J1
- CAN bus D-SUB 9-pin male connector, J3
- CAN bus 6-pin header male, J15
- XMOD JTAG header for access to System Controller CPLD, J35
- XMOD JTAG header for access to Zynq MPSoC, J24
- FMC B cooling fan, M3
- MicroSD Card socket (on bottom side), J16
- DisplayPort connector, J13
- USB3.0 A 2x , RJ45 1x (stacked), J7
- SFP+ 2x1 cage, J14
- PCIe x16 connector (one PCIe lane connected), J11
- FMC HPC connector, J5
- FMC-Fan connector 5V, J19
- USB3.0 connector, J8
- PC-BEEPER 4-pin header, J23
- SMA coaxial connector (SI5338A clock output), J32
- SMA coaxial connector (clock input to MPSoC module), J33
- MMC Card socket, J27
- Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J4
- Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J1
- Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J3
- Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J2
- CAN bus 6-pin header, J29
- CAN bus 10-pin connector, J24
- ARM JTAG 20-pin connector, J30
- ATX-24 power supply connector, J20
- 4-Wire PWM fan connector, J35
- JTAG/UART header ('XMOD FTDI JTAG Adapter'-compatible) for access to MPSoC module, J12
- JTAG/UART header ('XMOD FTDI JTAG Adapter'-compatible) for access to System Controller CPLDs, J28
- Power Jack 2.1mm 12V, J25
- 4-bit DIP-switch, S5
- Power Button, S1
- Samtec FireFly connector for reverse loopback, J21/J22
- Samtec FireFly connector (4 GT lanes bidirectional), J6/J15
- SATA header, J31
- 4-Wire PWM fan connector, J26
- I²C interface of programmable on-module PLL (10-pin header), J17
- Reset Button, S2
- INTEL HDA 9-pin header, J9
- Intel front panel (PWR-/RST-Button, HD-/PWR-LED) 9-pin header, J10
- Samtec FireFly connector J6/J15 I²C interface (3-pin header), J34
- 4-bit DIP-switch, S4
- PMOD connector, P3
- PMOD connector, P1
- 4-Wire PWM fan connector, J33
- Battery Holder CR1220, B1
- SMT coaxial connector (PLL Si5345A U17 clock input), J25
- Push Button, S1
- Push Button, S2
- DDR4 SO-DIMM socket, U3
- 4-bit DIP-switch, S4
- 4-bit DIP-switch, S3
- FMC connector (FMC A), J10
- FMC A cooling fan, M1
- FMC connector (FMC F), J21
- FMC F cooling fan, M6
- NGFF M.2 PCIe socket (Key M), U2
- SD Card socket, J11
- User LEDs (3x green, 1x red) with LED light pipe, D13 ... D16
- Green LEDs dedicated to USB3 hub U4, D17 ... D19
- Red LED indicating FPGAs 'DONE' signal, D6
- 4-Wire PWM fan connector, J2
- Battery Holder CR1220, B1Xilinx Zynq Ultrascale+ MPSoC, U1
Initial Delivery State
Storage device name | Content | Notes |
---|---|---|
User configuration EEPROMs (1x Microchip 24LC128-I/ST, 3x Microchip 24AA025E48T-I/OT) | Empty | Not programmed |
USB3 HUB Configuration EEPROM (Microchip 24LC128-I/ST) | Empty | Not programmed |
Si5338A programmable PLL NVM OTP | Empty | Not programmed |
Si5345A programmable PLL NVM OTP | Empty | Not programmed |
...
Refer also to the documentation of the SC CPLD firmware of the TEB0911 board, section 'boot mode'.
Signals, Interfaces and Pins
...
Overview
Content Tools