Page History
...
| Date | Vivado | Project Built | Authors | Description |
|---|---|---|---|---|
| 2019-02-07 | 2018.2 | TE0807-StarterKit_noprebuilt-vivado_2018.2-build_04_20190207092514.zip TE0807-StarterKit-vivado_2018.2-build_04_20190207092334.zip | John Hartfiel |
|
| 2018-09-09.04 | 2018.2 | TE0807-StarterKit_noprebuilt-vivado_2018.2-build_03_20180904122245.zip TE0807-StarterKit-vivado_2018.2-build_03_20180904121600.zip | John Hartfiel |
|
| 2018.-05.-24 | 2017.4 | TE0807-StarterKit_noprebuilt-vivado_2017.4-build_10_20180524150124.zip TE0807-StarterKit-vivado_2017.4-build_10_20180524150106.zip | John Hartfiel |
|
| 2018-02-06 | 2017.4 | TE0807-StarterKit_noprebuilt-vivado_2017.4-build_05_20180206082637.zip TE0807-StarterKit-vivado_2017.4-build_05_20180206082621.zip | John Hartfiel |
|
| 2018-02-05 | 2017.4 | TE0807-StarterKit-vivado_2017.4-build_05_20180205101252.zip TE0807-StarterKit_noprebuilt-vivado_2017.4-build_05_20180205101306.zip | John Hartfiel |
|
| 2018-01-18 | 2017.4 | TE0807-StarterKit_noprebuilt-vivado_2017.4-build_05_20180118152938.zip TE0807-StarterKit-vivado_2017.4-build_05_20180118152922.zip | John Hartfiel |
|
...
| Module Model | Board Part Short Name | PCB Revision Support | DDR | QSPI Flash | Others | Notes |
|---|---|---|---|---|---|---|
| TE0807-01-ES2 | es2_sk | REV01 | 2GB | 64MB | ||
| TE0807-02-07EV-1E | 7ev_1e_sk | REV02 | 4GB | 64MB |
Note: Design contains also Board Part Files for TE0807 only configuration, this boart part files are not used for this reference design.
...
- Prepare HW like described on section Programming 70156402
- Connect UART USB (JTAG XMOD)
- Select SD Card as Boot Mode (or QSPI - depending on step 1)
Note: See TRM of the Carrier, which is used. - (Optional) Insert PCIe Card (detection depends on Linux driver. Only some basic drivers are installed)
- (Optional) Connect Sata Disc
- (Optional) Connect DisplayPort Monitor (List of usable Monitors: https://www.xilinx.com/support/answers/68671.html)
- (Optional) Connect Network Cable
- Power On PCB
Note: 1. ZynqMP Boot ROM loads PMU Firmware and FSBL from SD into OCM, 2. FSBL loads ATF(bl31.elf) and U-boot from SD/QSPI into DDR, 3. U-boot load Linux from SD into DDR.
...
| Date | Document Revision | Authors | Description | ||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
|
| ||||||||||||||||||||||
| v.13 | John Hartfiel |
| |||||||||||||||||||||||
| v.12 | John Hartfiel |
| |||||||||||||||||||||||
| v.10 | John Hartfiel |
| |||||||||||||||||||||||
| v.9 | John Hartfiel |
| |||||||||||||||||||||||
| 2018-01-29 | v.4 | John Hartfiel |
| ||||||||||||||||||||||
| 2018-01-18 | v.3 | John Hartfiel |
| ||||||||||||||||||||||
| All |
|
...
Overview
Content Tools