Versions Compared

Old Version 46

changes.mady.by.user Martin Rohrmüller

Saved on

compared with

New Version 47

changes.mady.by.user Martin Rohrmüller

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

  • Microsemi SmartFusion2 SoC FPGA (M2S010)
  • 128 MByte DDR3 SDRAM
  • On board power converters for all needed voltages
  • 40 pin header (compatible to Raspberry Pi pinout)
  • 4 x 12 pin Pmods
  • Gigabit Ethernet PHY with RGMII interface
  • JTAG and UART via Micro USB
  • 3 pin header for Live Probes
  • 2 x User Button
  • 2 x status LED

  • 1 x  RGB LED


Additional assembly options are available for cost or performance optimization upon request.


Block Diagram

Scroll Title
anchorBD_TEM0002
titleFigure 1: TEM0002-01 block diagram.
Scroll Ignore

draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramNameBD_TEM0002-01
simpleViewertrue
width
linksauto
tbstyletop
lboxtrue
diagramWidth641
revision16

Scroll Only

...

Image Added

Main Components


Scroll Title
anchorMC_TEM0002
titleFigure 2: TEM0002-01

...

main components.

...

Scroll Ignore
draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramNameTEM0002_

...

bottom_numbered
simpleViewertrue
width400
linksauto
tbstyletop
lboxtrue
diagramWidth641
revision

...

7

draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramNameTEM0002_

...

top_numbered
simpleViewertrue
width400
linksauto
tbstyletop
lboxtrue
diagramWidth641
revision

...

8

Scroll Only

Image AddedImage Added

  1. Microsemi SmartFusion2 SoC FPGA, U2
  2. USB to UART/FIFO (FTDI FT2232H), U3
  3. Gigabit ETH connector, J2
  4. 4x  2x6 pin Pmod, P1, P2, P3, P4
  5. GPIO pin header compatible to Raspberry Pi, J8
  6. Micro USB 2.0, J1
  7. EEPROM 4KBIT (M93C66-R), U6
  8. 2x User Button, S4, S5
  9. RGB LED, D3
  10. LED red, D1 and green, D2
  11. Live Probe pins, J4
  12. Reset jumper, J13
  13. JTAG select jumper, J6
  14. Board power header, J5
  15. 1Gb DDR3/L SDRAM, U5
  16. MicroSD memory card connector, J3
  17. Gigabit Ethernet PHY, U1

...

Power Distribution Dependencies

Scroll Title
anchorBD_TEM0002
titleFigure 3: Module power distribution diagram.
Scroll Ignore

draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramNamePD_TEM0002-01
simpleViewertrue
width
linksauto
tbstyletop
lboxtrue
diagramWidth

...

641
revision

...

9

Scroll Only

Image Added


Power Rails

Power Rail Name

Connector pin

Direction

Notes
VINJ5-1InputMain supply voltage.
5VJ8-2, J8-4Output
3.3VJ8-1, J8-17Output
1.5V-Output

1.2V

-Output
GNDJ5-2, J8-9/25/39/6/14/20/30/34

...

All dimensions are given in millimeters.Image RemovedImage Removed

Scroll Title
anchorTD_TEM0002
titleFigure 4: Module physical dimensions drawing.

Image Added

Image Added

Revision History

Hardware Revision History

...