Page History

<!--
Template Revision 1.64
(HTML comments will be not displayed in the document, no need to remove them. For Template/Skeleton changes, increase Template Revision number. So we can check faster, if the TRM style is up to date).
-->

<!--
General Notes:
If some section is CPLD firmware dependent, make a note and if available link to the CPLD firmware description. It's in the TE shop download area in the corresponding module -> revision -> firmware folder.
-->

<!--
General Notes:
Designate all graphics and pictures with a number and a description. For example "Figure 1: TE07xx-xx Block Diagram" or "Table 1: Initial delivery state". "Figure x" and "Table x" have to be formatted to bold.  
-->

Overview

Refer to https://wiki.trenz-electronic.de/display/PD/TE0791+TRM for the current online version of this manual and other available documentation.

The Trenz Electronic TE0791-01 is an adapter board for use with the XMOD TE0790 board. The adapter board provides several connector types to get access to the signals and interfaces of the XMOD board. As further option footprints are available for JST Wire-To-Board IDC connectors with two different pin-assignments.

Key Features

• Xmod form-factor
  • size: 20 x 25 mm
  • M3 mounting hole
• Different connector types available
  
  • 2x6 PMOD connector
  • JTAG 1-row pin header female
  • 2x optional JST Wire-To-Board 6-pin IDC connector
  • 2x optional JST Wire-To-Board 10-pin IDC connector
  • IDC connectors with different pin-assignment each
    

Block Diagram

Image Added

Figure 1: TE0791-01 block diagram.

Main Components

Image Added

Figure 2: TE0790-02 main components. Top side view

1. 2x6 PMOD connector solder pads, J1 (on bottom side)
2. 6-Pin header solder pads, J8
3. 12-Pin header solder pads, J2
4. 10-pin IDC connector solder pads, J4 (solder pads J5 on bottom side)
5. 6-pin IDC connector solder pads, J3 (solder pads J6 on bottom side)
6. 2x6 PMOD connector
7. 1-row 6-pin header female (2.54 mm pitch)
8. 2-row 12-pin header male (2.54 mm pitch)

Signals, Interfaces and Pins

Figure 3: Connector Location

2x6 Pin Header

The 2x6 pin header (2.54mm grid size, male) J2 of the TE0791 board have to be connected to the corresponding XMOD pin header on the TE0790 board. The signal assignment of the pin header on the TE0790 board depends on the configuration of its System Controller CPLD firmware.

The pin assignment on the TE0791 adapter board is the same as on the TE0790 XMOD board:

Table 1: Pin header J2 signal assignment. *pin 1 on header J2 of the adapter board

1x6 Pin Header

On the female 1-row 6-pin header (2.54mm grid size, female) J8 are the XMOD signals C, D, F and H available. At standard System Controller CPLD firmware, this signals create the JTAG interface of the XMOD board:

Table 2: Pin header J8 signal assignment with standard TE0790 CPLD firmware

2x6 PMOD Header

On the 2x6 PMOD header J1 are all XMOD signals A - H available. The pin- and signal-assignment with standard System Controller CPLD firmware of the XMOD board are as follows:

Table 3: PMOD J1 signal assignment with standard TE0790 CPLD firmware

10-pin IDC Connector

On the TE0791 board are footprints available for 10-pin JST Wire-To-Board IDC connectors J4 and J5 with two different pin-assignments, where all XMOD signals A - H are available. The pin- and signal-assignment with standard System Controller CPLD firmware of the XMOD board are as follows:

Table 4: IDC connector J4 and J5 signal assignment with standard TE0790 CPLD firmware

6-pin IDC Connector

On the TE0791 board are footprints available for 6-pin JST Wire-To-Board IDC connectors J3 and J6 with two different pin-assignments, where the XMOD signals C, D, F and H are available. At standard System Controller CPLD firmware, this signals create the JTAG interface of the XMOD board:

Table 5: IDC connector J3 and J6 signal assignment with standard TE0790 CPLD firmware

Technical Specification

Physical Dimensions

• Module size: 24,65mm × 20,02mm.  Please download the assembly diagram for exact numbers.

• Mating height with standard pin headers: 9.5 mm.

• PCB thickness: 1.6 mm.

• Highest part on PCB: approx. 7 mm on top side, 5 mm on bottom side. Please download the step model for exact numbers.

All dimensions are given in millimeters and mil.

Image Added

Figure 4: Board physical dimensions drawing.

Revision History

Hardware Revision History

Table 6: Board hardware revision history.

Document Change History

<!--
Generate new entry:
1.add new row below first
2.Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number
3.Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description.
  -->

Table 7: Document change history.

Disclaimer

 Some sources available on XMOD-JST-HEADER