Versions Compared

Old Version 113

changes.mady.by.user Pedram Babakhani

Saved on

compared with

New Version Current

changes.mady.by.user John Hartfiel

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Page properties
hiddentrue
idComments

Note:
Use 'Key Features' description in shoping page, for example: https://shop.trenz-electronic.de/de/TE0728-04-1Q-SoC-Micromodul-mit-Xilinx-Automotive-Zynq-7020-512-MByte-DDR3L-6-x-6-cm

  • Module: 
    • Trenz Electronic Module TE0745
    • Temperature: -40 to 85 °C
  • On Board:
    • 24V power supply
    over ARKZ950/2 connecting
    • terminal
    • 1 x EMI Network Filter
    • 3 x Variable Step Down Regulator Module (VDRM) with head sink
    • 2 x Synchronous Buck Regulator
    • 2 x Button (User / Reset)
    • 2 x LED (Green)
  • Interfaces:
    • 1 x XMOD (TE0790) Pin Header (JTAG / UART)
    • 1 x Pin Header (JTAG)
    • 1 x microSD connector
    • 1 x RJ45 Ethernet connector
    • 1 x USB Host Connector
    • 8 x SFP-Connector
    • 6 x Pin Header 50 pol. (FPGA Bank I/O's and Power)
    • 6 x Pin Header 12 pol. (FPGA Bank I/O's and Power)
    • 1 x battery holder
    • 2 x DIP Switch Array (VCC_HR_B / Modi)
  • 2 x Button (User / Reset)
  • 2 x LED (Green)
  • Dimension: 200 mm x 231 mm

Block Diagram

...

Scroll Title
anchorFigure_OV_BD
titleTEB0745 block diagram


Scroll Ignore

draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramDisplayName
lboxtrue
revision1421
diagramNameTEB0745_OV_BD
simpleViewerfalse
width
linksauto
tbstylehidden
diagramWidth640


Scroll Only



...

Scroll Title
anchorTable_OV_IDS
titleInitial delivery state of programmable devices on the module

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Storage device name

Content

Notes

EEPROMNot ProgrammedEUI-64 number programmed

Can be used for MAC



Configuration Signals

Page properties
hiddentrue
idComments
  • Overview of Boot Mode, Reset, Enables.

...

Scroll Title
anchorTable_OV_BP
titleBoot process.

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

MODE Signal State

ConnectConnected toB2BStatusBoot Mode

BOOTMODE

S1J2-133OpenQSPI
ShortSD Card


...

Scroll Title
anchorTable_OV_RST
titleReset process.

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Type

Schematic

Connection
Connected toB2BNote
Main Module Reset (
RST_IN_N
)

Push Button

S2 or J12-11 XMOD connector (Default XMOD Button)

, S2

J2-131Low Active Reset


Signals, Interfaces and Pins

...

Scroll Title
anchorTable_SIP_B2B
titleGeneral PL I/O to B2B connectors information

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

B2B ConnectorInterfacesNumber of I/ONotes
J1

User I/O

48 singel ended, 24 Differential

2 singel ended

Connected to Bank 13

48 singel ended, 24 Differential

2 singel ended

Connected to Bank 12
JTAG Interface5 single endedTCK, TDI, TMS, TDO, JTAG_EN
SFP+ Connector8 DiffSPF4....7_RX_N/P , SPF4....7_TX_N/P
J2

Ethernet PHY4 Differential
2 single endedPHY_LED0...1
USB1 DifferentialOTG_N/P
Control Signals3 single endedPS_SRST, BOOTMODE, RST_IN_N
Power Control Signal2 single endedPWR_PS_OK, PWR_PL_OK
I2C Bus2 single endedI2C_SDA, I2C_SCL
User I/O4 single endedMIO12...15

J3


User I/O6 Single endedMIO46...51
SD Card Connector6 Single endedSD_CLK, SD_CMD, SD_DAT0...3 (MIO40...45)
SFP+ Connector8 DifferentialSPF0....3_RX_N/P , SPF0....3_TX_N/P

...


XMOD Pin Header

JTAG access to the TEB0745 SoM is available through B2B connector JB1 and JB2. JTAG_EN is connected to J1-138, JTAG_EN can be activated through DIP Switch S1-2.

Scroll Title
anchorTable_SIP_JTG
titleJTAG pins connection

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Designator

Connected to

B2B Pin

XMOD Header JB1Note
AMIO15J2-129JB1-3UART TX - Input to the module
BMIO14J2-127JB1-7UART RX - Output of the module
CTCKJ1-143JB1-4JTAG interface signal
DTDOJ1-145JB1-8JTAG interface signal
FTDIJ1-142JB1-10JTAG interface signal
HTMSJ1-144JB1-12

JTAG interface signal

GRST_IN_NJ2-131JB1-11RESET will be connected to Push Button on JTAG Programmer

...


There is a DIP switch, S2, on TE0790 adapter which must be set as following.

Scroll Title
anchorTable_OBPSIP_I2CXmod_RTCDIP
titleI2C Address for RTC Xmod Adapter DIP-Switch Setting Description

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

I2C DeviceI2C AddressDesignatorNotes
I2C_EXP0x72U16SFP 0-9
EEPROM0x51U33I/O EXP0x20...27U18...25

...

DIP Switch,S2DefaultDescription
1ONUpdate Mode JTAG access to SC CPLD only
2OFFMust be always in OFF state.
3OFFVIO is supplied from Module
4ON3.3V  from XMOD


SFP+ Connectors

The TEB0745 is equipped with 8 SFP+ Connectors, 

Scroll Title
anchorTable_SIPOBP_TestPointSFP
titleTest Points InformationSFP Connectors

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Test Point
Pin
Signals
Connected to 

B2B Connector

Notes
15V-2VBAT_INJ1-1463VCCIO18VJ2- J34VCC_HR_BJ15-9GND-10PS_1.8VJ211VCC_HR_BJ1123.3VJ1- J213--14--15PWR_PL_OKJ2- 13516PWR_PS_OKJ2-1391724V_FUSED-183.3V_SFP-

On-board Peripherals

Page properties
hiddentrue
idComments

Notes :

  • add subsection for every component which is important for design, for example:
    • Two 100 Mbit Ethernet Transciever PHY
    • USB PHY
    • Programmable Clock Generator
    • Oscillators
    • eMMCs
    • RTC
    • FTDI
    • ...
    • DIP-Switches
    • Buttons
    • LEDs

SD Card Socket

Power supply voltage for SD card holder is 3.3V.

...

anchorTable_OBP_SDcard
titleSD card interface MIOs and pins

...

RJ45 Connector

Etherneth Socket is connected to Board to Board (B2B)  JM2.

...

anchorTable_OBP_RJ45
titleLAN Transformer

...

SFP+ , J4SFP+, J6SFP+, J8SFP+, J10SFP+, J13SFP+, J15SFP+, J18SFP+, J20
TD+B2B, J3B2B, J3B2B, J3B2B, J3B2B, J1B2B, J1B2B, J1B2B, J1GT
TD-B2B, J3B2B, J3B2B, J3B2B, J3B2B, J1B2B, J1B2B, J1B2B, J1GT
RD+B2B, J3B2B, J3B2B, J3B2B, J3B2B, J1B2B, J1B2B, J1B2B, J1GT
RD-B2B, J3B2B, J3B2B, J3B2B, J3B2B, J1B2B, J1B2B, J1B2B, J1GT
TX FAULTIO Exp, U18IO Exp, U19IO Exp, U20IO Exp, U21IO Exp, U22IO Exp, U23IO Exp, U24IO Exp, U25SFP_CTRL
TX DISABLE IO Exp, U18IO Exp, U19IO Exp, U20IO Exp, U21IO Exp, U22IO Exp, U23IO Exp, U24IO Exp, U25SFP_CTRL
MOD-DEF2 IO Exp, U18IO Exp, U19IO Exp, U20IO Exp, U21IO Exp, U22IO Exp, U23IO Exp, U24IO Exp, U25SFP_CTRL
MOD-DEF1IO Exp, U18IO Exp, U19IO Exp, U20IO Exp, U21IO Exp, U22IO Exp, U23IO Exp, U24IO Exp, U25SFP_CTRL
MOD-DEF0IO Exp, U18IO Exp, U19IO Exp, U20IO Exp, U21IO Exp, U22IO Exp, U23IO Exp, U24IO Exp, U25SFP_CTRL
RS0IO Exp, U18IO Exp, U19IO Exp, U20IO Exp, U21IO Exp, U22IO Exp, U23IO Exp, U24IO Exp, U25SFP_CTRL
LOSIO Exp, U18IO Exp, U19IO Exp, U20IO Exp, U21IO Exp, U22IO Exp, U23IO Exp, U24IO Exp, U25SFP_CTRL
RS1IO Exp, U18IO Exp, U19IO Exp, U20IO Exp, U21IO Exp, U22IO Exp, U23IO Exp, U24IO Exp, U25SFP_CTRL


SD Card Socket

Power supply voltage for SD card holder is 3.3V.

Scroll Title
anchorTable_OBP_SDcard
titleSD card

...

EEPROM

Scroll Title
anchorTable_OBP_EEP
titleI2C EEPROM interface MIOs and pins

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

MIO Pin
Signals
Schematic
Connected toB2BNotes
MIO10I2C_SCLJ2-119MIO11I2C_SDAJ2-121

DIP Switches

There are two DIP Switches S1,S4.

SD_CLKMIO40J3-150
SD_CMDMIO41J3-152
SD_DAT0MIO42J3-154
SD_DAT1MIO43J3-156
SD_DAT2MIO44J3-158
SD_DAT3MIO45J3-160


RJ45 Connector

Ethernet Socket is connected to Board to Board (B2B)  JM2.

BootMode
Scroll Title
anchorTable_OBP_RJ45
titleLAN Transformer

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeaders

Scroll Title
anchorTable_OBP_DIP
titleDIP Switch S1

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Designator
Signal
Connected to
B2B
B2BNoteS1-A
Notes
PHY_MDIO0_PJ2-120
PHY_MDIO_NJ2-
133S1-BJTAG_ENJ1-148S1-C-S1-DPS_SWJ2-123

...

122
PHY_MDIO1_PJ2-126
PHY_MDIO1_NJ2-128
PHY_MDIO2_PJ2-132
PHY_MDIO2_NJ2-134
PHY_MDIO3_PJ2-138
PHY_MDIO3_NJ2-140
PHY_LED0J2-144
PHY_LED1J2-146


Test Points

Power
Scroll Title
anchorTable_OBPSIP_DIPTestPoint
titleDIP Switch S4Test Points Information

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

S4-1S4-2S4-3S4-4

Test Point

Signals

B2B Connector

Notes
TP 15V-
TP 2VBAT_INJ1-146
TP 3VCCIO18VJ2- J3
TP 4
VCC_HR_B
NotesOFFOFFOFFN.C.1,8VOFFOFFONN.C.1,5VOFFONOFFN.C.3,3VOFFONONN.C.2,5VONOFFOFFN.C.0,8VONOFFONN.C.Do not useONONOFFN.C.1,25VONONONN.C.1,2V