Page History

Overview

Zynq Design PS with Linux and  two Ethernet PHYs connected over EMIO and PL.

Refer to http://trenz.org/te0728-info for the current online version of this manual and other available documentation.

Key Features

Page properties
hidden true id Comments
Notes :

Revision History

Release Notes and Know Issues

Page properties
hidden true id Comments
Notes :

Requirements

Software

Page properties
hidden true id Comments
Notes : list of software which was used to generate the design

Hardware

Basic description of TE Board Part Files is available on TE Board Part Files.

Complete List is available on <design name>/board_files/*_board_files.csv

Design supports following modules

:

Design supports following carriers:

Additional HW Requirements:

Content

For general structure and of the reference design, see Project Delivery -

AMD devices

Design Sources

Additional Sources

Prebuilt

Download

Reference Design is only usable with the specified Vivado/

Vitis/PetaLinux

version. Do never use different Versions of Xilinx Software for the same Project.

Reference Design is available on:

• TE0728 "Test Board" Reference Design

Design Flow

Trenz Electronic provides a tcl based built environment based on Xilinx Design Flow.

See also:

• AMD Development

• Tools#XilinxSoftware-BasicUserGuides
• Vivado Projects - TE Reference Design
•  Project Delivery.

The Trenz Electronic FPGA Reference Designs are TCL-script based project. Command files for execution will be generated with "_create_win_setup.cmd" on Windows OS and "_create_linux_setup.sh" on Linux OS.

TE Scripts are only needed to generate the vivado project, all other additional steps are optional and can also executed by Xilinx Vivado/

Vitis GUI.  For currently Scripts limitations on Win and Linux OS see: Project Delivery Currently limitations of functionality

1. Run _create_win_setup.cmd/_create_linux_setup.sh and follow instructions on shell:

1. Code Block
   language bash theme Midnight title _create_win_setup.cmd/_create_linux_setup.sh
   ------------------------Set design paths---------------------------- -- Run Design with: _create_win_setup -- Use Design Path: <absolute project path> -------------------------------------------------------------------- -------------------------TE Reference Design--------------------------- -------------------------------------------------------------------- -- (0) Module selection guide, project creation...prebuilt export... -- (1) Create minimum setup of CMD-Files and exit Batch -- (2) Create maximum setup of CMD-Files and exit Batch -- (3) (internal only) Dev -- (4) (internal only) Prod -- (c) Go to CMD-File Generation (Manual setup) -- (d) Go to Documentation (Web Documentation) -- (g) Install Board Files from Xilinx Board Store (beta) -- (a) Start design with unsupported Vivado Version (beta) -- (x) Exit Batch (nothing is done!) ---- Select (ex.:'0' for module selection guide):

   
   

2. Press 0 and enter to start "Module Selection Guide"
3. Createproject and follow instructions of the product selection guide, settings file will be configured automatically during this process.
   

   • optional for manual changes: Select correct device and Xilinx install path on "design_basic_settings.cmd" and create Vivado project with "vivado_create_project_guimode.cmd"

     
     

     Note
     Note: Select correct one, see also Vivado Board Part Flow

     
     

4. Create Project
   
   1. Select correct device and Xilinx install path on "design_basic_settings.cmd" and create Vivado project with "vivado_create_project_guimode.cmd"
      Note: Select correct one, see TE Board Part Files

5. Create hardware description file (.xsa file) for PetaLinux project and export to prebuilt folder

   Code Block
   language py theme Midnight title run on Vivado TCL (Script generates design and export files into "<project folder>\prebuilt\hardware\<short name>")
   TE::hw_build_design -export_prebuilt

   
   

   Info
   Using Vivado GUI is the same, except file export to prebuilt folder.

   
   

6. Create and configure your PetaLinux project with exported .xsa-file, see PetaLinux KICKstart
   • use TE Template from "<project folder>\os\petalinux"

   • use exported .xsa file from "<project folder>\prebuilt\hardware\<short name>" . Note: HW Export from Vivado GUI creates another path as default workspace.

   • The build images are located in the "<plnx-proj-root>/images/linux" directory

7. Configure the boot.scr file as needed, see Distro Boot with Boot.scr
   

8. Copy PetaLinux build image files to prebuilt folder

   • copy u-boot.elf, image.ub and boot.scr from "<plnx-proj-root>/images/linux" to prebuilt folder
     

     Info
     "<project folder>\prebuilt\os\petalinux\<ddr size>" or "<project folder>\prebuilt\os\petalinux\<short name>"

     
     

     Page properties
     hidden true id Comments
     This step depends on Xilinx Device/Hardware for Zynq-7000 series copy u-boot.elf, image.ub and boot.scr from "<plnx-proj-root>/images/linux" to prebuilt folder for ZynqMP copy u-boot.elf, bl31.elf, image.ub and boot.scr from "<plnx-proj-root>/images/linux" to prebuilt folder for ... ...

     
     

9. Generate Programming Files with Vitis

   Code Block
   language py theme Midnight title run on Vivado TCL (Script generates applications and bootable files, which are defined in "test_board\sw_lib\apps_list.csv")
   TE::sw_run_vitis -all TE::sw_run_vitis (optional; Start Vitis from Vivado GUI or start with TE Scripts on Vivado TCL)

   
   

   Note
   TCL scripts generate also platform project, this must be done manually in case GUI is used. See Vitis

   
   

Launch

Programming

Xilinx documentation for programming and debugging: Vivado/SDK/SDSoC-Xilinx Software Programming and Debugging

Get prebuilt boot binaries

1. Run _create_win_setup.cmd/_create_linux_setup.sh and follow instructions on shell
2. Press 0 and enter to start "Module Selection Guide"
   1. Select assembly version
   2. Validate selection

   3. Select create and open delivery binary folder

      Info
      Note: Folder "<project folder>\_binaries_<Article Name>" with subfolder "boot_<app name>" for different applications will be generated

      
      

QSPI-Boot mode

Option for Boot.bin on QSPI Flash and image.ub and boot.scr on SD or USB.

1. Connect JTAG and power on carrier with module

2. Open Vivado Project with "vivado_open_existing_project_guimode.cmd" or if not created, create with "vivado_create_project_guimode.cmd"

   Code Block
   language py theme Midnight title run on Vivado TCL (Script programs BOOT.bin on QSPI flash)
   TE::pr_program_flash -swapp u-boot TE::pr_program_flash -swapp hello_te0820 (optional)

   
   

   Note
   To program with Vitis/Vivado GUI, use special FSBL (fsbl_flash) on setup

   
   

3. Copy image.ub and boot.scr on SD or USB
   
   • use files from "<project folder>\_binaries_<Article Name>\boot_linux" from generated binary folder,see: Get prebuilt boot binaries
   • or use prebuilt file location, see "<project folder>\prebuilt\file_location.txt"
4. Set Boot Mode to QSPI-Boot and insert SD or USB.
   • Depends on Carrier, see carrier TRM.

SD-Boot mode

1. Copy image.ub, boot.src and Boot.bin on SD
   
   • use files from "<project folder>\_binaries_<Article Name>\boot_linux" from generated binary folder, see: Get prebuilt boot binaries
   • or use prebuilt file location, see "<project folder>\prebuilt\file_location.txt"
2. Set Boot Mode to SD-Boot.
   • Depends on Carrier, see carrier TRM.
3. Insert SD-Card in SD-Slot.

JTAG

Not used on this Example.

Usage

1. Prepare HW like described on section Programming
2. Connect UART USB (most cases same as JTAG)

3. Select SD Card as Boot Mode (or QSPI - depending on step 1)

   Info
   Note: See TRM of the Carrier, which is used.

   
   

   Tip

   Starting with Petalinux version 2020.1, the industry standard "Distro-Boot" boot flow for U-Boot was introduced, which significantly expands the possibilities of the boot process and has the primary goal of making booting much more standardised and predictable. The boot options described above describe the common boot processes for this hardware; other boot options are possible. For more information see Distro Boot with Boot.scr

   
   

4. Power On PCB

   Expand
   title boot process
   1. Zynq Boot ROM loads FSBL from SD/QSPI into OCM, 2. FSBL init PS, programs PL using the bitstream and loads U-boot from SD into DDR, 3. U-boot loads Linux (image.ub) from SD/QSPI/... into DDR

   
   

   Page properties
   hidden true id Comments
   This step depends on Xilinx Device/Hardware for Zynq-7000 series 1. Zynq Boot ROM loads FSBL from SD/QSPI into OCM, 2. FSBL init the PS, programs the PL using the bitstream and loads U-boot from SD/QSPI into DDR, 3. U-boot loads Linux (image.ub) from SD/QSPI/... into DDR for ZynqMP??? 1. ZynqMP Boot ROM loads FSBL from SD/QSPI into OCM, 2. FSBL init the PS, programs the PL using the bitstream and loads PMU, ATF and U-boot from SD/QSPI into DDR, 3. U-boot loads Linux (image.ub) from SD/QSPI/... into DDR for Microblaze 1. FPGA Loads Bitfile from Flash, 2. MCS Firmware configure SI5338 and starts Microblaze, 3. SREC Bootloader from Bitfile Firmware loads U-Boot into DDR (This takes a while), 4. U-boot loads Linux from QSPI Flash into DDR for native FPGA ...

   
   

Linux

1. Open Serial Console (e.g. putty)
   
   • Speed: 115200

   • select COM Port

     Info
     Win OS, see device manager, Linux OS see dmesg |grep tty (UART is *USB1)

     
     

2. Linux Console:
   

   Code Block
   language bash theme Midnight
   petalinux login: root Password: root

   
   

   Info
   Note: Wait until Linux boot finished

   
   

3. You can use Linux shell now.

   Code Block
   language bash theme Midnight
   i2cdetect -y -r 0 (check I2C 0 Bus) dmesg | grep rtc (RTC check) udhcpc (ETH0/ETH1 check) cd /etc/init.d/networking restart (Network setting can be reset if it is necessary) ifconfig (It is visible that both ethernet devices eth0 and eth1 have their own IP address.)

   
   

System Design - Vivado

Block Design

PS Interfaces

Constrains

Basic module constrains

#
# Common bitgen related settings
#

set_property BITSTREAM.GENERAL.COMPRESS TRUE [current_design]
set_property CONFIG_VOLTAGE 3.3 [current_design]
set_property CFGBVS VCCO [current_design]

set_property BITSTREAM.CONFIG.USR_ACCESS TIMESTAMP [current_design]

Design specific constrain

#############
#ETH0/ETH1
#####
#pwr_down
set_property PACKAGE_PIN L21 [get_ports {PHY_PD[0]}]
set_property PACKAGE_PIN R20 [get_ports {PHY_PD[1]}]
#rst_n
set_property PACKAGE_PIN M15 [get_ports {PHY_RSTN[0]}]
set_property PACKAGE_PIN R16 [get_ports {PHY_RSTN[1]}]
#io standard
set_property IOSTANDARD LVCMOS33 [get_ports {PHY*}]
set_property IOSTANDARD LVCMOS33 [get_ports MDIO_*]
set_property IOSTANDARD LVCMOS33 [get_ports {MII_*}]
#pullup/down for PHY address 1
set_property PULLUP   true [get_ports MII_col]
set_property PULLDOWN true [get_ports {MII_rxd[0]}]
set_property PULLDOWN true [get_ports {MII_rxd[1]}]
set_property PULLDOWN true [get_ports {MII_rxd[2]}]
set_property PULLDOWN true [get_ports {MII_rxd[3]}]
#pullup/down for PHY address 3
set_property PULLUP true [get_ports MII_1_col]
set_property PULLUP true [get_ports {MII_1_rxd[0]}]
set_property PULLDOWN true [get_ports {MII_1_rxd[1]}]
set_property PULLDOWN true [get_ports {MII_1_rxd[2]}]
set_property PULLDOWN true [get_ports {MII_1_rxd[3]}]

#############
#ETH0
#####
set_property PACKAGE_PIN M16 [get_ports MDIO_ETHERNET_0_mdio_io]
set_property PACKAGE_PIN P16 [get_ports MDIO_ETHERNET_0_mdc]
set_property PACKAGE_PIN M22 [get_ports {MII_txd[3]}]
set_property PACKAGE_PIN K21 [get_ports {MII_txd[2]}]
set_property PACKAGE_PIN M17 [get_ports {MII_txd[1]}]
set_property PACKAGE_PIN J22 [get_ports {MII_txd[0]}]
set_property PACKAGE_PIN J20 [get_ports {MII_rxd[3]}]
set_property PACKAGE_PIN J18 [get_ports {MII_rxd[2]}]
set_property PACKAGE_PIN K18 [get_ports {MII_rxd[1]}]
set_property PACKAGE_PIN L17 [get_ports {MII_rxd[0]}]
set_property PACKAGE_PIN L16 [get_ports MII_col]
set_property PACKAGE_PIN N15 [get_ports MII_crs]
set_property PACKAGE_PIN L18 [get_ports MII_rx_clk]
set_property PACKAGE_PIN P15 [get_ports MII_rx_dv]
set_property PACKAGE_PIN P17 [get_ports MII_rx_er]
set_property PACKAGE_PIN K19 [get_ports MII_tx_clk]
set_property PACKAGE_PIN J21 [get_ports MII_tx_en]

#############
#ETH1
#####
set_property PACKAGE_PIN T16 [get_ports MDIO_ETHERNET_1_mdio_io]
set_property PACKAGE_PIN T17 [get_ports MDIO_ETHERNET_1_mdc]
set_property PACKAGE_PIN R21 [get_ports {MII_1_txd[3]}]
set_property PACKAGE_PIN P22 [get_ports {MII_1_txd[2]}]
set_property PACKAGE_PIN P21 [get_ports {MII_1_txd[1]}]
set_property PACKAGE_PIN N22 [get_ports {MII_1_txd[0]}]
set_property PACKAGE_PIN T19 [get_ports {MII_1_rxd[3]}]
set_property PACKAGE_PIN T18 [get_ports {MII_1_rxd[2]}]
set_property PACKAGE_PIN R19 [get_ports {MII_1_rxd[1]}]
set_property PACKAGE_PIN R18 [get_ports {MII_1_rxd[0]}]
set_property PACKAGE_PIN P20 [get_ports MII_1_col]
set_property PACKAGE_PIN N18 [get_ports MII_1_crs]
set_property PACKAGE_PIN M19 [get_ports MII_1_rx_clk]
set_property PACKAGE_PIN N17 [get_ports MII_1_rx_dv]
set_property PACKAGE_PIN P18 [get_ports MII_1_rx_er]
set_property PACKAGE_PIN N19 [get_ports MII_1_tx_clk]
set_property PACKAGE_PIN M21 [get_ports MII_1_tx_en]

Software Design - Vitis

For Vitis project creation, follow instructions from:

Vitis

Application

Template location: "<project folder>\sw_lib\sw_apps\"

zynq_fsbl

TE modified 2020.2 FSBL

General:

• Modified Files: main.c, fsbl_hooks.h/.c (search for 'TE Mod' on source code)

• Add Files: te_fsbl_hooks.h/.c (for hooks and board)

• General Changes: 
  
  • Display FSBL Banner and Device ID

Module Specific:

• only active FSBL banner independence form debug flags

zynq_fsbl_flash

TE modified 2020.2 FSBL

FSBL(for Vivado/Vitis GUI only) to initialise Zynq for QSPI programming

General:

• Modified Files: main.c
• General Changes:
  
  • Display FSBL Banner
  • Set FSBL Boot Mode to JTAG
  • Disable Memory initialisation

hello_te0728

Hello TE0728 is a Xilinx Hello World example as endless loop instead of one console output.

u-boot

U-Boot.elf is generated with PetaLinux. Vitis is used to generate Boot.bin.

Software Design -  PetaLinux

For PetaLinux installation and project creation, follow instructions from:

• PetaLinux KICKstart

Config

Start with petalinux-config or petalinux-config --get-hw-description

Changes:

• No changes.

U-Boot

Start with petalinux-config -c u-boot

Changes:

• No changes.

Device Tree

/include/ "system-conf.dtsi"
/ {
};
 
/* QSPI PHY */
&qspi {
    #address-cells = <1>;
    #size-cells = <0>;
    status = "okay";
    flash0: flash@0 {
        compatible = "jedec,spi-nor";
        reg = <0x0>;
        #address-cells = <1>;
        #size-cells = <1>;
    };
};
 

/* SDIO 

FSBL patch

Must be add manually, see template

Kernel

Start with petalinux-config -c kernel

Changes

:

• RTC_DRV_RV3029C2=y
• DP83848_PHY=y

Rootfs

Start with petalinux-config -c rootfs

Changes:

• I2C-tools=y
• CONFIG_util-linux-mount=y
• CONFIG_util-linux-umount=y
• busybox-httpd = y
• CONFIG_util-linux-umount=y
• CONFIG_util-linux-mount=y

Applications

See "<project folder>\os\petalinux\project-spec\meta-user\recipes-apps\"

startup

Script App to load init.sh from SD Card if available.

See: \os\petalinux

\project-spec\meta-user\recipes-apps\startup\files

webfwu

Webserver application suitable for Zynq access. Need busybox-httpd

See: \os\petalinux\project-spec\meta-user\recipes-apps\webfwu\files

Additional Software

No additional software is needed.

Appx. A: Change History and Legal Notices

Document Change History

To get content of older revision  got to "Change History"  of this page and select older document revision number.

Legal Notices