Page History
...
HTML |
---|
<!-- Template Revision 1.4 beta (HTML comment will not display, it's not needed to remove them. For Template/Skeleton changes, increase Template Revision number. So we can check faster, if the TRM style is up to date) --> |
Scroll Ignore |
---|
Download PDF version of this document. |
Scroll pdf ignore | |
---|---|
Table of Contents
|
...
- Xilinx Zynq UltraScale+ MPSoC 784 pin package (options: ZU2CG, ZU2EG, ZU3CG, ZU3EG, ZU4CG, ZU4EV)
- Memory
- 64-Bit DDR4, 8 GByte maximum
- Dual SPI boot Flash in parallel, 512 128 MByte maximum - User I/O
- 65 x MIO, 48 x HD (all), 156 x HP (3 banks)
- Serial transceiver: 4 x GTR (+ 4 x GTH transceiver with ZU4CG or ZU4EV MPSoC)
- Transceiver clocks inputs and outputs
- PLL clock generator inputs and outputs - Size: 52 x 76 mm, 3 mm mounting holes for skyline heat spreader
- B2B connectors: 4 x 160 pin
- Si5338A - 4 output PLL
- All power supplies on board, single 3.3V power source required
- LP, FP, PL separately controlled power domains - Support for all boot modes (except NAND) and scenarios
- Support for any combination of PS connected peripherals
...
- Xilinx ZYNQ UltraScale+ MPSoC, U1
- 2-Input AND Gate, U39
- Red LED (DONE), D1
- 256Mx16 DDR4-2400 SDRAM, U12
- 256Mx16 DDR4-2400 SDRAM, U9
- 256Mx16 DDR4-2400 SDRAM, U2
- 256Mx16 DDR4-2400 SDRAM, U3
- 12A PowerSoC DC-DC converter, U4 (either TPS548A28RWWR or MPQ8633BGLE-Z is assembled which is up to Trenz Electronic GmbH)
- 1.5A LDO DC-DC converter, U10
- 1.5A LDO DC-DC converter, U8
- Voltage monitor circuit, U41
- 0.35A LDO DC-DC converter, U26
- 0.35A LDO DC-DC converter, U27
- Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J3
- Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J1
- Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J4
- Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J2
- 4-channel programmable PLL clock generator, U5
- Low-power programmable oscillator @ 25.000000 MHz, U5
- Low-power programmable oscillator @ 33.333333 MHz (PS_CLK), U32
- 256 Mbit serial NOR Flash memory, U7
- 256 Mbit serial NOR Flash memory, U17
...
Storage device name | Content | Notes |
---|---|---|
User configuration EEPROMs with MAC address (1x Microchip 24LC128-I/ST, 3x Microchip 24AA025E48T-I/OT) | Not programmed | available since PCB REV02 |
SPI Flash main array | Not programmed | - |
eFUSE Security | Not programmed | - |
Si5338A programmable PLL NVM OTP | Not programmed- | Only volatile memory is programmable of field. NVM can't be program on field. Custom assembly variant with preprogrammed NVM is possible on request |
Table 1: Initial Delivery State of the flash memories
...
Bank | Type | B2B Connector | Schematic Names / Connector Pins | I/O Signal Count | LVDS Pairs Count | VCCO Bank Voltage | Notes |
---|---|---|---|---|---|---|---|
251) | HD | J3 | B25_L1_P ... B25_L12_P | 24 I/O's | 12 | VCCO25 | VCCO max. 3.3V |
262) | HD | J3 | B26_L1_P ... B26_L12_P | 24 I/O's | 12 | VCCO26 | VCCO max. 3.3V |
64 | HP | J4 | B64_L1_P ... B64_L24_P B_64B64_T0 ... BB64_64_T3 | 52 I/O's | 24 | VCCO64 | VCCO max. 1.8V |
65 | HP | J4 | B65_L1_P ... B65_L24_P B_65B65_T0 ... BB65_65_T3 | 52 I/O's | 24 | VCCO65 | VCCO max. 1.8V |
66 | HP | J1 | B66_L1_P ... B66_L24_P B_65B66_T0 ... B_65B66_T3 | 52 I/O's | 24 | VCCO66 | VCCO max. 1.8V |
500 | MIO | J3 | MIO13 ... MIO25 | 13 I/O's | - | PS_1V8 | user configurable I/O's on B2B |
501 | MIO | J3 | MIO26 ... MIO51 | 26 I/O's | - | PS_1V8 | user configurable I/O's on B2B |
502 | MIO | J3 | MIO52 ... MIO77 | 26 I/O's | - | PS_1V8 | user configurable I/O's on B2B |
...
Bank | Type | B2B Connector | Count of MGT Lanes | Schematic Names / Connector Pins | MGT Bank's Reference Clock Inputs |
---|---|---|---|---|---|
2241)
| GTH | J1 | 4 GTH lanes (4 RX / 4TX) | B224_RX3_P, B224_RX3_N, pins J1-51, J1-53 B224_RX2_P, B224_RX2_N, pins J1-57, J1-59 B224_RX1_P, B224_RX1_N, pins J1-63, J1-65 B224_RX0_P, B224_RX0_N, pins J1-69, J1-71 | 1 reference clock signal (B224_CLK0) from B2B connector 1 reference clock signal (B224_CLK1) from programmable |
505 | GTR | J2 | 4 GTR lanes (4 RX / 4TX) | B505_RX3_P, B505_RX3_N, pins J2-5154, J2-4952 B505_RX2_P, B505_RX2_N, pins J2-5760, J2-5558 B505_RX1_P, B505_RX1_N, pins J2-6366, J2-6164 B505_RX0_P, B505_RX0_N, pins J2-6972, J2-6770 | 2 reference clock signals (B505_CLK0, B505_CLK1) from B2B connector 2 reference clock signals (B505_CLK2, B505_CLK3) from programmable |
...
Quad SPI Flash memory ICs U7 and U17 are connected to the Zynq PS QSPI0 interface via PS MIO bank 500, pins MIO0..MIO5 and MIO7..MIO12.
MIO | U7 Pin | Pin Name | MIO | U17 Pin | Pin Name | ||
---|---|---|---|---|---|---|---|
0 | B2 | CLK | 7 | C2 | CS# | ||
1 | D2 | DO/IO1 | 8 | D3 | DI/IO0 | ||
2 | C4 | WP#/IO2 | 9 | D2 | DO/IO1 | ||
3 | D4 | HOLD#/IO3 | 10 | C4 | WP#/IO2 | ||
4 | D3 | DI/IO0 | 11 | D4 | HOLD#/IO3 | ||
5 | C2 | CS# | 12 | B2 | CLK |
Table 7: MIO pin assignment of the Quad SPI Flash memory ICs
...
The TE0803 SoM can be configured with max. 512 MByte Flash memory for configuration and operation. Flash size and type depends on assembly version.
Name | IC | Designator | PS7 | MIO | Notes |
---|---|---|---|---|---|
SPI Flash | N25Q256A11E1240E | U7 | QSPI0 | MIO0 ... MIO5 | Dual parallel booting possible, 32 MByte memory per Flash IC at standard configuration |
SPI Flash | N25Q256A11E1240E | U17 | QSPI0 | MIO7 ... MIO12 | As above |
...
The TE0803-01 SoM is equipped with with four DDR4-2400 SDRAM modules chips with up to 8 GByte of memory. The SDRAM modules chips are connected to the Zynq MPSoC's PS DDR controller (bank 504) via 64-bit wide data bus.
Refer to the Xilinx Zynq UltraScale+ datasheet DS925 for more information, if the specific Zynq UltraScale+ MPSoC chip on module supports the maximum data transmission rate of 2400 MByte/s.
Configuration EEPROM
The TE0803 (PCB REV02 or newer) contains EEPROMs for general user purposes and mac address. The EEPROMs are provided by Microchip and all have I²C interfaces:
EEPROM Modell | Schematic Designator | Memory Density | Purpose |
---|---|---|---|
24AA025E48T-I/OT | U41 | 2 Kbit | user |
Table 21: On-board configuration EEPROMs overview
Programmable PLL Programmable PLL Clock Generator
Following table illustrates on-board Si5338A programmable clock multiplier chip inputs and outputs:
Input | Connected to | Frequency | Notes |
---|---|---|---|
IN1 / IN2 | B2B Connector pins J2-4, J2-6 (differential pair) | User | AC decoupling required on base |
IN3 | On-board Oscillator (U6) | 25.000000 MHz | - |
Output | Connected to | Frequency | Notes |
CLK0 A/B | B2B Connector pins J2-1, J2-3 (differential pair) | User | Default off |
CLK1 A/B | B224 CLK1 (only available at ZU5EV MPSoC with ZU4 and higher ) | User | Default off |
CLK2 A/B | B505 CLK3 | User | Default off |
CLK3 A/B | B505 CLK2 | User | Default off |
Table 11: Programmable PLL clock generator input/output
The Si5345A Si5338A programmable clock generator's control interface pins are exposed to B2B connector J2. For further information refer to the Si5338A data sheet.
...
Table 12: B2B connector pin-out of Si5338A control interface
Note |
---|
Si5338A OTP ROM Si5338A NVM is not programmed by default at delivery, so it . It is customers responsibility to either configure Si5338A volatile memory during FSBL or then use Silicon Labs programmer and burn the OTP ROM with customer fixed clock setup. |
...
. Custom assembly variant with preprogrammed NVM is possible on request. |
Refer to Si5338A datasheet for more information.
...
Figure 3: Power Distribution Diagram (For U4 either TPS548A28RWWR or MPQ8633BGLE-Z is assembled which is up to Trenz Electronic GmbH)
Note |
---|
Current rating of Samtec Razor Beam™ LSHMBeam LP Terminal/Socket Strip ST5/SS5 B2B connectors is 21.0A 5 A per pin (2 adjacent pins powered1 pin powered per row). |
Power-On Sequence Diagram
...
Enable-Signal | B2B Connector Pin | Max. Voltage | Note | Power-Good-Signal | B2B Connector Pin | Pull-up Resistor | Note | ||
---|---|---|---|---|---|---|---|---|---|
EN_LPD | J2-108 | 6V | TPS82085SIL data sheet | LP_GOOD | J2-106 | 4K7, pulled up to LP_DCDC | - | ||
EN_FPD | J2-102 | DCDCIN | NC7S08P5X data sheet | PG_FPD | J2-110 | 4K7, pulled up to DCDCIN | - | ||
EN_PL | J2-101 | max PL_DCIN | Left floating for logic high (drive to GND for logic low) | PG_PL | J2-104 | External pull-up needed (max. voltage 'GT_DCDC'), Max. sink current 1 mA | TPS82085SIL / | ||
EN_DDR | J2-112 | DCDCIN | NC7S08P5X data sheet | PG_DDR | J2-114 | 4K7, pulled up to DCDCIN | - | ||
EN_PSGT | J2-84 | DCDCIN | NC7S08P5X data sheet | PG_PSGT | J2-82 | External pull-up needed (max. 5.5V), Max. sink current 1 mA | TPS74801 datasheet | ||
EN_GT_R | J2-95 | GT_DCDC | NC7S08P5X data sheet | PG_GT_R | J2-91 | External pull-up needed (max. 5.5V), Max. sink current 1 mA | TPS74401 datasheet | ||
- | - | - | - | PG_VCU_1V0 | J2-97 | External pull-up needed (max. 5.5V), | TPS82085SIL datasheet |
Table 16: Recommended operation conditions of DC-DC converter control signals
Warning |
---|
To avoid any damage to the MPSoC module, check for stabilized on-board voltages in steady state before powering up the MPSoC's I/O bank voltages VCCOx. All I/O's should be tri-stated during power-on sequence. |
...
Voltages on B2B Connectors | B2B J1 Pin | B2B J2 Pin | B2B J3 Pin | B2B J4 Pin | Input/ Output | Note |
---|---|---|---|---|---|---|
PL_DCIN | J1-151, J1-153,J1-155, J1-157, J1-159 | - | - | - | Input | - |
DCDCIN | - | J2-154, J2-156, J2-158, J2-160, J2-153, J2-155, J2-157, J2-159 | - | - | Input | - |
LP_DCDC | - | J2-138, J2-140, J2-142, J2-144 | - | - | Input | - |
PS_BATT | - | J2-125 | - | - | Input | - |
GT_DCDC | - | - | J3-157, J3-158, J3-159, J3-160 | - | Input | - |
PS_1V8 | - | J2-99 | J3-147, J3-148 | - | Output | Internal voltage level 1.8V nominal output |
PL_1V8 | J1-91, J1-121 | - | - | - | Output | Internal voltage level 1.8V nominal output |
DDR_1V2 | - | J2-135 | - | - | Output | Internal voltage level 1.2V nominal output |
...
Variants Currently In Production
...
Trenz shop TE0803 overview page | |
---|---|
English page | German page |
Technical Specifications
Absolute Maximum Ratings
Parameter | Min | Max | Unit | Notes / Reference Document |
---|---|---|---|---|
PL_DCIN | -0.3 | 4 | V | TPS82085SIL / EN63A0QI data sheet / Limit is LP_DCDC over EN/PG |
DCDCIN | -0.3 | 4 | V | TPS82085SIL / TPS51206PSQ data sheet / Limit is LP_DCDC over EN/PG |
LP_DCDC | -0.3 | 4 | V | TPS3106K33DBVR data sheet |
GT_DCDC |
Table 19: Differences between module TE0803-01 variants
1) Not yet available
All variants are rated for Extended operating temperature range (0 - 100 °C).
Technical Specifications
Absolute Maximum Ratings
Parameter | Min | Max | Unit | Notes / Reference Document |
---|---|---|---|---|
PL_DCIN | -0.3 | 74 | V | TPS82085SIL / EN63A0QI data sheet |
DCDCIN | -0.3 | 7 | V | TPS82085SIL / TPS51206PSQ data sheet |
LP_DCDC | -0.3 | 4 | V | TPS3106K33DBVR data sheet |
GT_DCDC | -0.3 | 7 | V | TPS82085SIL data sheet |
data sheet / Limit is LP_DCDC over EN/PG | ||||
PS_BATT | -0.5 | 2 | V | Xilinx DS925 data sheet |
VCCO for HD I/O banks | -0.5 | 3.4 | V | Xilinx DS925 data sheet |
VCCO for HP I/O banks | -0.5 | 2 | V | Xilinx DS925 data sheet |
VREF | -0.5 | 2 | V | Xilinx DS925 data sheet |
I/O input voltage for HD I/O banks | -0.55 | VCCO + 0.55 | V | Xilinx DS925 data sheet |
I/O input voltage for HP I/O banks | -0.55 | VCCO + 0.55 | V | Xilinx DS925 data sheet |
PS I/O input voltage (MIO pins) | -0.5 | VCCO_PSIO + 0.55 | V | Xilinx DS925 data sheet, VCCO_PSIO 1.8V nominally |
Receiver (RXP/RXN) and transmitter (TXP/TXN) absolute input voltage | -0.5 | 1.2 | V | Xilinx DS925 data sheet |
Voltage on input pins of NC7S08P5X 2-Input AND Gate | -0.5 | VCC + 0.5 | V | NC7S08P5X data sheet, see schematic for VCC |
Voltage on input pins (nMR) of TPS3106K33DBVR Voltage Monitor, U41 | -0.3 | VDD + 0.3 | V | TPS3106 data sheet, VDD = LP_DCDC |
"Enable"-signals on TPS82085SIL ('EN_LPD') | -0.3 | 7 | V | TPS82085SIL data sheet |
Storage temperature (ambient) | -40 | 100 | °C | ROHM Semiconductor SML-P11 Series data sheet |
...
Parameter | Min | Max | Unit | Notes / Reference Document |
---|---|---|---|---|
PL_DCIN | 23.53 | 3.6 | V | EN63A0QI / TPS82085SIL data sheet / Limit is LP_DCDC over EN/PG |
DCDCIN | 3.13 | 3.6 | V | TPS82085SIL / TPS51206PSQ data sheet / Limit is LP_DCDC over EN/PG |
LP_DCDC | 23.53 | 3.6 | V | TPS82085SIL / TPS3106K33DBVR data sheet |
GT_DCDC | 23.53 | 3.6 | V | TPS82085SIL data sheet / Limit is LP_DCDC over EN/PG |
PS_BATT | 1.2 | 1.5 | V | Xilinx DS925 data sheet |
VCCO for HD I/O banks | 1.14 | 3.4 | V | Xilinx DS925 data sheet |
VCCO for HP I/O banks | 0.95 | 1.9 | V | Xilinx DS925 data sheet |
I/O input voltage for HD I/O banks. | -0.2 | VCCO + 0.2 | V | Xilinx DS925 data sheet |
I/O input voltage for HP I/O banks | -0.2 | VCCO + 0.2 | V | Xilinx DS925 data sheet |
PS I/O input voltage (MIO pins) | -0.2 | VCCO_PSIO + 0.2 | V | Xilinx DS925 data sheet, VCCO_PSIO 1.8V nominally |
Voltage on input pins of NC7S08P5X 2-Input AND Gate | 0 | VCC | V | NC7S08P5X data sheet, see schematic for connected VCCs |
Voltage on input pins (MR) of TPS3106K33DBVR Voltage Monitor, U41 | 0 | VDD | V | TPS3106 data sheet, VDD = LP_DCDC |
...
Operating Temperature Ranges
...
The module operating temperature range depends also on customer design and cooling solution. Please contact us for options.
...
- Module size: 52 mm × 76 mm. Please download the assembly diagram for exact numbers
- Mating height with standard connectors: 4mm5mm
- PCB thickness: 1.6mm
- Highest part on PCB: approx. 3mm. Please download the step model for exact numbers
All dimensions are given in millimeters.
Revision History
Hardware Revision History
...
- for exact numbers
All dimensions are given in millimeters.
Revision History
Hardware Revision History
Date | Revision | Notes | Link to PCN | Documentation Link |
---|---|---|---|---|
2019-03-18 | 03 |
| TE0803 Product Change Notifications | TE0803-03 |
2018-07-19 | 02 |
| TE0803 Product Change Notifications | TE0803-02 |
2016-12-23 | 01 | First production release | - | TE0803-01 |
Hardware revision number is written on the PCB board together with the module model number separated by the dash.
Document Change History
Date | Revision | Contributors | Description | ||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
|
| ||||||||||||||||||||||||
22-02-25 | v.50 | John Hartfiel |
| ||||||||||||||||||||||||
22-02-08 | v.46 | John Hartfiel |
| ||||||||||||||||||||||||
2021-05-17 | v.41 | John Hartfiel |
| ||||||||||||||||||||||||
2021-03-11 | v.40 | John Hartfiel |
| ||||||||||||||||||||||||
2019-07-15 | v.36 | John Hartfiel |
| ||||||||||||||||||||||||
2019-07-02 | v.35 | John Hartfiel |
| ||||||||||||||||||||||||
2019-06-19 | v.33 | John Hartfiel |
| ||||||||||||||||||||||||
2018-08-20 | v.29 | John Hartfiel |
| ||||||||||||||||||||||||
2018-08-06 | v.28 | John Hartfiel |
| ||||||||||||||||||||||||
2017-11-13 | v.23 | Ali Naseri |
| ||||||||||||||||||||||||
2017-11-13 | v.19 |
Hardware revision number is written on the PCB board together with the module model number separated by the dash.
Document Change History
Date | Revision | Contributors | Description | |||
---|---|---|---|---|---|---|
Page info | modified-date | modified-date | dateFormat | yyyy-MM-dd | John Hartfiel |
|
2017-10-19 | v.18 | John Hartfiel |
| |||
2017-08-15 | v.17 | Vitali Tsiukala |
| |||
2017-08-07 | v.14 | Jan Kumann |
| |||
2017-05-17 | V.4 | Ali Naseri | Current TRM release. | |||
2017-05-10 | v.1 | Ali Naseri | Initial document. |
...