Versions Compared
Key
- This line was added.
- This line was removed.
- Formatting was changed.
Warning |
---|
Seite in Bearbeitung für zukünftiges Kundenformular oder Webseiteninhalt mit zusätzlichen Dienstleistungen |
Introduction
Trenz Electronic GmbH neben den Shop Produkten und kundenspezifische Hardware Anpassungen noch weitere Dienstleistungen für die Auslieferung der Produkte bereit. Dieser Dienstleistungen umfassen die Programmierung mit Kunden Firmware/FPGA Designs und Montageleistungen. Je nach Umfang werden Pauschalen oder spezifische Preismodelle verwendet. Trenz Electronic übernimmt dabei keine Haftung die durch fehlerhafte Kundendesigns entstehen
Allgemeine Bedingungen
- Mindestbestellmenge: idr. 100Stück, andernfalls muss ein Preisaufschlag vorgenommen werden
- Kosten für Erstmuster: Hardwarepreis+50 Euro
- Jeder Service muss vom Kunden mittels Erstmuster geprüft und freigegeben werden
- Risiken die durch explizite Anweisungen des Kunden entstehen werden vom Kunden selber getragen (z.B. Reduzierung von Testschritten zur Kostenoptimierung)
- je nach Kategorie müssen erweitere Angaben getätigt werden, sie Fragenkatalog
Kundenspezifische Firmware/FPGA Design Programmierung
offers additional services other than the store products and custom hardware adaptations. These services include programming with customer firmware/FPGA designs and pre-assembly services. Depending on the scope, fixed rates or specific pricing models are used. Trenz Electronic does not assume any liability resulting from incorrect customer specifications/designs.
General conditions and notes
- Minimum order quantity: usually 100 pieces, otherwise a price surcharge must be added
- Indicated prices are ballpark prices, price adjustments possible depending on volume and other variables
- Costs for verification sample: Hardware price + 100 Euro.
- Each service must be tested and approved by the customer by means of initial samples.
- Each adaption of the design after confirmation of initial samples will make another loop of verification samples necessary.
- Risks arising from explicit instructions from the customer are borne by the customer (e.g. reduction of test steps to optimize costs).
- Depending on the category, additional information must be provided, see questionnaire.
Custom firmware/FPGA design programming
Category | Description | Price per piece (guide prices) | Note |
---|---|---|---|
A | Recording | ||
Kategorie | Beschreibung | Preis pro Stück | Hinweis |
A | Bespielen (Flash/SD/eMMC) mit Kunden Designwith customer design |
|
|
A1 | Bespielen Recording (Flash/SD/eMMC) mit Kunden Design mit Verifikationwith customer design with verification |
|
|
A2 | CPLD/PLL(mit NVM)/PMIC |
|
|
B | Erweiterte Prüfung mit Start des Kundendesign |
|
|
C | Full Custom Testumgebung |
|
|
D | EFuse Programmierung |
|
|
Montageanpassungen
- Preis nach Prüfung
- Aufschlag bei Erstmuster
- eventuell Lagerkosten
- ohne zusätzliche Prüfung
- Preis nach Prüfung
- Aufschlag bei Erstmuster
- eventuell Lagerkosten
- Prüfungen wie Fotos...
| |||
B | Extended test with start of customer design |
|
|
C | Full Custom Test Environment |
|
|
D | Custom CPLD Firmware |
|
|
D1 | PMIC or other controller / Custom PLL(with NVM) |
|
|
E | EFuse Programming / Encrypting Key |
|
|
E1 | EFuse programming / encrypting key and advanced testing with start of customer design |
|
|
*Category color:
- Green: Standard service
- Yellow: Extended standard service
- Red: Special services that are checked separately and only offered under certain conditions
Mounting adjustments
Category | Description | Price per piece (guide prices) | Note |
---|---|---|---|
F | Custom assembly |
|
|
F1 | Custom assembly with verification |
|
|
*Category color:
- Green: Standard service
- Yellow: Extended standard service
- Red: Special services that are checked separately and only offered under certain conditions
Questionnaire
Required for category | Question/required data | Description |
---|---|---|
all |
Fragenkatalog
Benötigt für Typ | Frage/Benötigte Daten | Beschreibung | |
---|---|---|---|
alle (A*,B,C,D*,E*) | Wie lauten die MD5 Checksumme für alle übermittelten Dateien? | What are the MD5 checksum for all submitted files? |
|
A1,B,C,D1,DE1 | Which tests should be performedWelche Prüfungen sollen durchgeführt werden? |
| |
B,C,D*,E1 | Which tool version is used? |
| |
A1,A2,B | Welche Kompatibilität der What compatibility of B2B IOs ist zu gewährleisten? |
| |
C | Übermittlung einer vollständigen Testbeschreibung und Testequipment |
| |
C | Wie viel Zyklen darf das Testequipment verwendet werden? |
| |
C | Wird auch Ersatzequipment gestellt? |
| E/E1 | todo | todo
| |||
C | Transmission of a complete test description and test equipment |
| |
C | How many cycles may the test equipment be used? |
| |
C | Is replacement equipment also provided? |
| |
F/F1 | Mounting instructions available? |
| |
F/F1 | Loctite? |
| |
F/F1 | Are there customer supplied articles? |
| |
F/F1 | Are packaging regulations to be observed? |
|
More service offers
For additional service offers, the shipping costs are borne by the customer. 50 Euro initial cost for first basic inspection and first error analysis regardless of whether it can be repaired or not.
Category | Description | Price per piece (guide prices) | Note |
---|---|---|---|
Repair of defective boards |
|
| |
Reprogramming FTDI or CPLDs |
|
|
Disclaimer
Include Page | ||||
---|---|---|---|---|
|
Custom_table_size_100 |
---|
Scroll Only | ||
---|---|---|
|
Scroll pdf ignore | ||||||
---|---|---|---|---|---|---|
|