Page History

...

<!--
General Notes:
Designate all graphics and pictures with a number and a description. For example "Figure 1: TE07xx-xx Block Diagram" or "Table 1: Initial delivery state". "Figure x" and "Table x" have to be formatted to bold.  
-->

...

Refer to https://shopwiki.trenz-electronic.de/dedisplay/Download/?path=Trenz_Electronic/XMOD/TE0791 for downloadablePD/TE0791+TRM for the current online version of this manual and additionalother technicalavailable documentation of the product.

The Trenz Electronic TE0791-01 is an adapter board for use with the XMOD TE0790 board. The adapter board provides several connector types to get access to the signals and interfaces of the XMOD board. As further option footprints are available for JST Wire-To-Board IDC connectors with two different pin-assignments.

...

• Xmod form-factor
  • size: 20 x 25 mm
  • M3 mounting hole
• Different connector types available
  
  • 2x6 PMOD connector
  • JTAG 1-row pin header female
  • 2x optional JST Wire-To-Board 6-pin IDC connector
  • 2x optional JST Wire-To-Board 10-pin IDC connector
  • IDC connectors with different pin-assignment each
    

Block Diagram

Figure 1: TE0790 TE0791-02 01 block diagram.

Main Components

...

Figure 2: TE0790-02 main components. Bottom Top side view

1. 2x6 PMOD connector solder pads, J1 (on top bottom side)
2. 6-Pin header solder pads, J8
3. 12-Pin header solder pads, J2
4. 10-pin IDC connector solder pads, J4 (solder pads J5 on top bottom side)
5. 6-pin IDC connector solder pads, J3 (solder pads J6 on top bottom side)
6. 2x6 PMOD connector
7. 1-row 6-pin header female (2.54 mm pitch)
8. 2-row 12-pin header male (2.54 mm pitch)

Signals, Interfaces and Pins

Figure 3: Connector Location

2x6 Pin Header

The 2x6 pin header (2.54mm grid size, male) J2 of the TE0791 board have to be connected to the corresponding XMOD pin header on the TE0790 adapter board. The signal assignment of the pin header on the TE0790 adapter board depends on the configuration of its System Controller CPLD firmware.

The pin assignment on the TE0791 adapter board is the same as on the TE0790 XMOD board:

Table 1: Pin header J2 signal assignment. *pin 1 on header J2 of the adapter board

...

On the female 1-row 6-pin header J8 there (2.54mm grid size, female) J8 are the XMOD signals C, D, F and H available, which are the signals of . At standard System Controller CPLD firmware, this signals create the JTAG interface of the XMOD board with standard System Controller CPLD firmware:

Table 2: Pin header J8 signal assignment with standard TE0790 CPLD firmware

...

On the 2x6 PMOD header J1 there are the all XMOD signals A - H available. The pin- and signal-assignment with standard System Controller CPLD firmware of the XMOD board are as follows:

Table 3:

Table 3: PMOD J1 signal assignment with standard TE0790 CPLD firmware

10-pin IDC Connector

On the TE0791 board are footprints available for 10-pin JST Wire-To-Board IDC connectors J4 and J5 with two different pin-assignments, where all XMOD signals A - H are available. The pin- and signal-assignment with standard System Controller CPLD firmware of the XMOD board are as follows:

Table 4: IDC connector J4 and J5 signal assignment with standard TE0790 CPLD firmware

6-pin IDC Connector

On the TE0791 board are footprints available for 6-pin JST Wire-To-Board IDC connectors J3 and J6 with two different pin-assignments, where the XMOD signals C, D, F and H are available. At standard System Controller CPLD firmware, this signals create the JTAG interface of the XMOD board:

Table 5: IDC connector J3 and J6 signal assignment with standard TE0790 CPLD firmwareTable 4:

Technical Specification

Physical Dimensions

...

All dimensions are given in millimeters and mil.

Figure 34: Board physical dimensions drawing.

...

Hardware Revision History

Table 56: Board hardware revision history.

...

<!--
Generate new entry:
1.add new row below first
2.Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number
3.Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description.
  -->

Table 67: Document change history.

...