Versions Compared

Old Version 31

changes.mady.by.user John Hartfiel

Saved on

compared with

New Version Current

changes.mady.by.user Pedram Babakhani

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Scroll Title
anchorFigure_Overview
titleBoard Overview


Scroll Ignore
scroll-pdftrue
scroll-officetrue
scroll-chmtrue
scroll-docbooktrue
scroll-eclipsehelptrue
scroll-epubtrue
scroll-htmltrue

draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramDisplayName
lboxtrue
revision911
diagramNameTE0728_OV
simpleViewerfalse
width
linksauto
tbstylehidden
diagramWidth641


Scroll Only


  1. Barrel Jack Power Supply
  2. XMOD JTAG Adapter
  3. SD card holder
  4. Reset
  5. Boot mode Jumper
  6. Carrier LEDs (Red,Yellow,Green) D1
  7. Ethernet Socket
  8. Module LEDs (Green D4, Red D8)

Power supply

Page properties
hiddentrue
idComments

The input power supply must be mentioned.

Single 5V power supply with minimum current capability of 2.5A is recommended to power on the board. 

Scroll Title
anchorTable_DIP_PWR
titlePower Supply

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Overview 1

Supply VoltageMin CurrentNote

J9

5 V

2.5 A



DIP-Switches and Push Buttons

...

Scroll Title
anchorTable_DIP_PB
titleDIP Switches /Push Buttons

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Signal

Overview 4

Designator
Connected toB2BActive Level

S1

RESET

S1

J2-7

Active High


There is no DIPs on TE0728. In case of TE0790 (XMOD) usage, see DIPs mode.

...

Scroll Title
anchorTable_Jumpers
titleJumpers

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Designator
Overview 5Connected toB2BNote
J4Boot_RJ2-11Open: QSPI
Short: SD Card


LEDs

Page properties
hiddentrue
idComments

Explain all user LEDs functionality and connections.

...

Scroll Title
anchorTable_LED
titleCarrier LEDs

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Designator
Overview 6ColorConnected toB2BActive LevelNote
D1-ARedMIO48J2-30Active highUser LED
D1-BYellowMIO49J2-38Active highUser LED
D1-CGreenMIO50J2-36Active highUser LED


Furthermore, there are two user LEDs on module TE0728.

Scroll Title
anchorTable_LED
titleModule LEDs

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Designator
Overview 8ColorConnected toB2BActive LevelNote
D4GreenBank33 pin V18-Active highUser LED
D9GreenDONE_0

DONE pin
D8RedMIO7-Active highUser LED


JTAG/UART

Page properties
hiddentrue
idComments

Explain JTAG or UART connection breifly.

...

Scroll Title
anchorTable_XMOD_JTAG
titleXMOD JTAG DIP Switch

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Overview 2DIP SwitchSetting
JB11ON
2OFF
3OFF
4ON


Reference Designs

Page properties
hiddentrue
idComments

In this Section you must refer to the Reference Design (Test board) for the particular module.

For Example: TE0728 Reference Designs

...