Page History

...

The Trenz Electronic TE0724 is an industrial-grade SoC module based on Xilinx Zynq 7010/7020, which provides a dual core ARM Cortex A9 and a 7a 7-series FPGA logic. It provides a gigabit ethernet transceiver, 1GByte 1 GByte of DDR3L SDRAM, 32 64 MByte Flash memory as configration and data storage. It includes strong powerregulators power regulators for all needed voltages and a robust high-speed connector for in- and outputs. It has a 6 x 4 cm form factor.

...

• Xilinx Zynq XC7Z010-1CLG400I or XC7Z020-1CLG400I
• Dual-core ARM Cortex-A9 MPCore
• Max. 667 MHz
• Shock proof and vibration resistant
• Size 6 x 4 cm
• Plug-On-Modul with 1 × 160 Pin High-Speed connector
• 1 GByte DDR3L SDRAM
• 32 64 MByte QSPI Flash Speicher
• 1 x GBit Ethernet PHY
• 1 x MAC-Address EEPROM
• 128 KBit EEPROM
• 1 x CAN Transceiver
• On-Board DC/DC-regulators
• Excellent signal integrity due to evenly-spread supply pins

...

1. XILINX ZYNQ XC7Z020-2CLG400C, U1
2. Gigabit Ethernet Transceiver Alaska 88E1512, U7
3. Power Manager Dialog DA9062, U4
4. 1GByte - 2x 4Gbit DDR3L RAM, U3, U5
5. 32MByte Spansion 64MByte ISSI SPI Flash S25FL256IS25LP512M, U13
6. 128KByte Serial EEPROM Microchip 24AA, U10
7.  CAN Transceiver MCP2542FDT, U2
8.  160 Pin Samtec B2B Connector ST5-80-1.50-L-D-P-TR, J1

...

...

On-board QSPI flash memory (U13) on the TE0724-02 04 is a SPANSION S25FL256S ISSI IS25LP512M with 256 512 Mbit (32 64 MByte) storage capacity. This non volatile memory is used to store initial FPGA configuration. Besides FPGA configuration, remaining free flash memory can be used for user application and data storage. All four SPI data lines are connected to the FPGA allowing x1, x2 or x4 data bus widths. Maximum data rate depends on the selected bus width and clock frequency used.

...

A Microchip 24AA128T serial EEPROM (U10) is availabe available for e.g. module idetification identification and user Data. The device has 128Kbit memory with max 64 bytes page write capability. It is accessible over I²C bus with slave device address 0x50.

...

Power Distribution Dependencies

DCDC U8 component is either TPS82140 (2 A) or MUN12A (3 A) depending on the variant.

See Xilinx data sheet for additional information. User should also check related base board documentation when intending base board design for TE0724 module.

Power-On Sequence

The TE07024 TE0724 SoM meets the recommended criteria to power up the Xilinx Zynq MPSoC properly by keeping a specific sequence of enabling the on-board DC-DC converters dedicated to the particular functional units of the Zynq chip and powering up the on-board voltages. For a detailed description of the configurabel configurable Power Management IC please refer to the datasheet of  of dialog semicondutor DA9062.

...

Table 14: Module power rails.

...

Recommended Operating Conditions

Table 19: Module recommended operating conditions.

...

Hardware Revision History

...

...