Page History

...

...

For general structure and of the reference design, see Project Delivery - Xilinx AMD devices

Design Sources

...

Trenz Electronic provides a tcl based built environment based on Xilinx Design Flow.

See also:

• Xilinx AMD Development ToolsTools#XilinxSoftware-BasicUserGuides
• Vivado Projects - TE Reference Design
• Project Delivery.

The Trenz Electronic FPGA Reference Designs are TCL-script based project. Command files for execution will be generated with "_create_win_setup.cmd" on Windows OS and "_create_linux_setup.sh" on Linux OS.

TE Scripts are only needed to generate the vivado project, all other additional steps are optional and can also executed by Xilinx Vivado/SDK GUI.  For currently Scripts limitations on Win and Linux OS see: Project Delivery Currently limitations of functionality

1. _create_win_setup.cmd/_create_linux_setup.sh and follow instructions on shell:
   
2. Press 0 and enter to start "Module Selection Guide"
3. (optional Win OS) Generate Virtual Drive or use short directory  for the reference design (for example x:\<design name>)
4. Create Project (follow instruction of the product selection guide), settings file will be configured automatically during this process)
   
   1. (optional for manual changes) Select correct device and Xilinx install path on "design_basic_settings.cmd" and create Vivado project with "vivado_create_project_guimode.cmd"
      Note: Select correct one, see alsoTE Board Part Files
      1. Important: Use Board Part Files, which ends with *_tebf0808
5. Create XSA and export to prebuilt folder
   
   1. Run on Vivado TCL: TE::hw_build_design -export_prebuilt
      Note: Script generate design and export files into \prebuilt\hardware\<short dir>. Use GUI is the same, except file export to prebuilt folder
6. Create Linux (bl31.elf, uboot.elf , Image and system.dtb) with exported XSA
   
   1. XSA is exported to "prebuilt\hardware\<short name>"
      Note: HW Export from Vivado GUI create another path as default workspace.
   2. Create Linux images on VM, see PetaLinux KICKstart
      1. Use TE Template from /os/petalinux/
      2. Execute the script file for Debian/Ubuntu
7. Add Linux files (bl31.elf, uboot.elf , Image and system.dtb) to prebuilt folder
   
   1. "prebuilt\os\petalinux\<ddr size>" or "prebuilt\os\petalinux\<short name>"
8. Generate Programming Files with Vitis
   
   1. Run on Vivado TCL: TE::sw_run_vitis -all
      Note: Scripts generate applications and bootable files, which are defined in "sw_lib\apps_list.csv"
   2. (alternative) Start SDK with Vivado GUI or start with TE Scripts on Vivado TCL: TE::sw_run_vitis
      Note:  TCL scripts generate also platform project, this must be done manuelly in case GUI is used. See Vitis
9. Preparing SD card for SD Filesystem and hard disk for HD Filesystem → See Programming section

...

Xilinx documentation for programming and debugging: Vivado/SDK/SDSoC-Xilinx Software Programming and Debugging

Get prebuilt boot binaries

...

1. Prepare HW like described on section TE0808 StarterKit#Programming
2. Connect UART USB (JTAG XMOD)
3. Select SD Card as Boot Mode (or QSPI - depending on step 1)
   Note: See TRM of the Carrier, which is used.
4. (Optional) Insert PCIe Card (detection depends on Linux driver. Only some basic drivers are installed)
5. (Optional) Connect Sata Disc
6. (Optional) Connect DisplayPort Monitor (List of usable Monitors: https://www.xilinx.com/support/answers/68671.html)
7. (Optional) Connect Network Cable
8. Power On PCB
   Note: 1. ZynqMP Boot ROM loads PMU Firmware and  FSBL from SD into OCM, 2. FSBL loads ATF(bl31.elf) and U-boot from SD/QSPI into DDR, 3. U-boot load Linux from SD into DDR.

...