Skip to end of metadata
Go to start of metadata

Table of contents


Linux with basic periphery of TE0808 Starterkit (TEBF0808 Carrier).

Refer to for the current online version of this manual and other available documentation.

Key Features

  • Vitis/Vivado 2019.2
  • petalinux
  • Linux Debian 9 (Stretch) or Linux Ubuntu 18.04 (Bionic Beaver)
  • DisplayPort
  • TEBF0808
  • USB
  • ETH (use EEPROM MAC)
  • MAC from EEPROM
  • PCIe
  • SATA
  • SD
  • I2C
  • DP
  • user LED access
  • Modified FSBL for Si5338 programming
  • Special FSBL for QSPI Programming

Revision History

DateVivadoProject BuiltAuthorsDescription
Mohsen Chamanbaz
  • initial release
Design Revision History

Release Notes and Know Issues

IssuesDescriptionWorkaround/SolutionTo be fixed version
No known issues---------
Known Issues



Vitis2019.2needed, Vivado is included into Vitis installation

SD Card Formatter

format SD Card

Win32 DiskImager

burn generated image on SD
SI ClockBuilder Pro---optional


Basic description of TE Board Part Files is available on TE Board Part Files.

Complete List is available on <design name>/board_files/*_board_files.csv

Design supports following modules:

Module ModelBoard Part Short NamePCB Revision SupportDDRQSPI FlashEMMCOthersNotes
TE0808-ES1          es1_2gb      REV03|REV02 2GB      64MB       NA         NA               Not longer supported by vivado       
TE0808-ES2          es2_2gb      REV04|REV03 2GB      64MB       NA         NA               Not longer supported by vivado                   
TE0808-2ES2         2es2_2gb     REV04|REV03 2GB      64MB       NA         NA               Not longer supported by vivado                
TE0808-04-09EG-1EA  9eg_1e_2gb   REV04       2GB      64MB       NA         NA               
TE0808-04-09EG-1EB  9eg_1e_4gb   REV04       4GB      64MB       NA         NA               
TE0808-04-09EG-1ED  9eg_1e_4gb   REV04       4GB      64MB       NA         1 mm connectors
TE0808-04-09EG-2IB  9eg_2i_4gb   REV04       4GB      64MB       NA         NA               
TE0808-04-15EG-1EB  15eg_1e_4gb  REV04       4GB      64MB       NA         NA               
TE0808-04-09EG-1EE  9eg_1e_4gb   REV04       4GB      128MB      NA         NA               
TE0808-04-09EG-1EL  9eg_1e_4gb   REV04       4GB      128MB      NA         1 mm connectors
TE0808-04-09EG-2IE  9eg_2i_4gb   REV04       4GB      128MB      NA         NA               
TE0808-04-15EG-1EE  15eg_1e_4gb  REV04       4GB      128MB      NA         NA               
TE0808-04-06EG-1EE  6eg_1e_4gb   REV04       4GB      128MB      NA         NA               
TE0808-04-06EG-1E3  6eg_1e_4gb   REV04       4GB      128MB      NA         1 mm connectors
TE0808-04-6GI21-L   6eg_2i_4gb   REV04       4GB      128MB      NA         1 mm connectors
TE0808-04-6GI21-A   6eg_2i_4gb   REV04       4GB      128MB      NA         NA               
TE0808-04-6BI21-A   6eg_1i_4gb   REV04       4GB      128MB      NA         NA               
TE0808-04-9GI21-A   9eg_2i_4gb   REV04       4GB      128MB      NA         NA               
TE0808-04-9BE21-A   9eg_1e_4gb   REV04       4GB      128MB      NA         NA               
TE0808-04-6BE21-L   6eg_1e_4gb   REV04       4GB      128MB      NA         1 mm connectors
TE0808-04-6BE21-A   6eg_1e_4gb   REV04       4GB      128MB      NA         NA               
TE0808-04-9BE21-L   9eg_1e_4gb   REV04       4GB      128MB      NA         1 mm connectors
TE0808-04-BBE21-A   15eg_1e_4gb  REV04       4GB      128MB      NA         NA               
TE0808-04-6BI21-X6eg_1i_4gbREV04       4GB128MBNANAU41 replaced with schottky diodes
Hardware Modules

Note: Design contains also Board Part Files for TE0808 only configuration, this boart part files are not used for this reference design.

Design supports following carriers:

Carrier ModelNotes
TEBF0808Used as reference carrier. Important: CPLD Firmware REV07 or newer is recommended
Hardware Carrier

Additional HW Requirements:

Additional HardwareNotes
CoolerIt's recommended to use cooler on ZynqMP device
USB CableConnect to USB2 or better USB3 Hub for proper power supply over USB
DP MonitorOptional HW
Not all monitors are supported, also adapter to other standards can make trouble.
Design was tested with  DELL U2412M
Micro USB to USB A AdapterAdapter for USB Hub
USB HUBTo connect Mouse and Keyboard simultaneously
USB Keyboardneed for Ubuntu/Debian GUI
USB Mouseneed for Ubuntu/Debian GUI
DP Cable--
Sata DiskOptional HW
SATA CableOptional HW
PCIe CardOptional HW
ETH Cable

Optional HW
Ethernet works with DHCP, but can be setup also manually

SD Card16GB
Additional Hardware


For general structure and of the reference design, see Project Delivery - Xilinx devices

Design Sources

Vivado<design name>/block_design
<design name>/constraints
<design name>/ip_lib
Vivado Project will be generated by TE Scripts
Vitis<design name>/sw_libAdditional Software Template for Vitis and apps_list.csv with settings automatically for Vitis app generation
PetaLinux<design name>/os/petalinuxPetaLinux template with current configuration
Design sources

Additional Sources

SI5345<design name>/misc/Si5345SI5345 Project with current PLL Configuration
Additional design sources





BIF-File*.bifFile with description to generate Bin-File
BIN-File*.binFlash Configuration File with Boot-Image (Zynq-FPGAs)
BIT-File*.bitFPGA (PL Part) Configuration File
DebugProbes-File*.ltxDefinition File for Vivado/Vivado Labtools Debugging Interface
Diverse Reports---Report files in different formats
Hardware-Platform-Specification-Files*.xsaExported Vivado Hardware Specification for Vitis and PetaLinux
LabTools Project-File*.lprVivado Labtools Project File
OS-Image*.ubImage with Linux Kernel (On Petalinux optional with Devicetree and RAM-Disk)
Image---Generic Linux kernel binary image file
Software-Application-File*.elfSoftware Application for Zynq or MicroBlaze Processor Systems
Device Tree Blob File*.dtbContains a Device Tree Blob
Prebuilt files (only on ZIP with prebult content)


Reference Design is only usable with the specified Vivado/SDK/PetaLinux/SDx version. Do never use different Versions of Xilinx Software for the same Project.

Reference Design is available on:

Design Flow

Reference Design is available with and without prebuilt files. It's recommended to use TE prebuilt files for first lunch.

Trenz Electronic provides a tcl based built environment based on Xilinx Design Flow.

See also:

The Trenz Electronic FPGA Reference Designs are TCL-script based project. Command files for execution will be generated with "_create_win_setup.cmd" on Windows OS and "" on Linux OS.

TE Scripts are only needed to generate the vivado project, all other additional steps are optional and can also executed by Xilinx Vivado/SDK GUI.  For currently Scripts limitations on Win and Linux OS see: Project Delivery Currently limitations of functionality

  1. _create_win_setup.cmd/ and follow instructions on shell:
  2. Press 0 and enter to start "Module Selection Guide"
  3. (optional Win OS) Generate Virtual Drive or use short directory  for the reference design (for example x:\<design name>)
  4. Create Project (follow instruction of the product selection guide), settings file will be configured automatically during this process)
    1. (optional for manual changes) Select correct device and Xilinx install path on "design_basic_settings.cmd" and create Vivado project with "vivado_create_project_guimode.cmd"
      Note: Select correct one, see alsoTE Board Part Files
      1. Important: Use Board Part Files, which ends with *_tebf0808
  5. Create XSA and export to prebuilt folder
    1. Run on Vivado TCL: TE::hw_build_design -export_prebuilt
      Note: Script generate design and export files into \prebuilt\hardware\<short dir>. Use GUI is the same, except file export to prebuilt folder
  6. Create Linux (bl31.elf, uboot.elf , Image and system.dtb) with exported XSA
    1. XSA is exported to "prebuilt\hardware\<short name>"
      Note: HW Export from Vivado GUI create another path as default workspace.
    2. Create Linux images on VM, see PetaLinux KICKstart
      1. Use TE Template from /os/petalinux/
      2. Execute the script file for Debian/Ubuntu
  7. Add Linux files (bl31.elf, uboot.elf , Image and system.dtb) to prebuilt folder
    1. "prebuilt\os\petalinux\<ddr size>" or "prebuilt\os\petalinux\<short name>"
  8. Generate Programming Files with Vitis
    1. Run on Vivado TCL: TE::sw_run_vitis -all
      Note: Scripts generate applications and bootable files, which are defined in "sw_lib\apps_list.csv"
    2. (alternative) Start SDK with Vivado GUI or start with TE Scripts on Vivado TCL: TE::sw_run_vitis
      Note:  TCL scripts generate also platform project, this must be done manuelly in case GUI is used. See Vitis
  9. Preparing SD card for SD Filesystem and hard disk for HD Filesystem → See Programming section


For basic board setup, LEDs... see: TEBF0808 Getting Started


Check Module and Carrier TRMs for proper HW configuration before you try any design.

Xilinx documentation for programming and debugging: Vivado/SDK/SDSoC-Xilinx Software Programming and Debugging

Get prebuilt boot binaries

  1. _create_win_setup.cmd/ and follow instructions on shell
  2. Press 0 and enter to start "Module Selection Guide"
    1. Select assembly version
    2. Validate selection
    3. Select Create and open delivery binary folder
      Note: Folder (<project foler>/_binaries_<Artikel Name>) with subfolder (boot_<app name>) for different applications will be generated


Not used in this example.


  1. Format the SD Card with SD Card Formatter or other tool
  2. Write the Debian image or Ubuntu image file on SD Card with Win32DiskImager
  3. select the device tree depending on your ROOTFS location:
    1. system_sd.dtb : This file ist used , if the root file system is located on SD card.
    2. system_harddisk.dtb : This file ist used , if the root file system is located on hard disk.
    3. Note: To use one of the DTB files, this file must be renamed to system.dtb
  4. Rename selected device tree to system.dtb  (for Hard Disk usage, see also "Hard Disk (optional)")
  5. Copy Petalinux  Image (not use image.ub), system.dtb and Boot.bin files on SD-Card.
    • use files from (<project foler>/_binaries_<Articel Name>)/boot_linux from generated binary folder,see: Get prebuilt boot binaries
    • or use prebuilt file location, see <design_name>/prebuilt/readme_file_location.txt
  6. Set Boot Mode to SD-Boot.
    • Depends on Carrier, see carrier TRM.
  7. Insert SD-Card in SD-Slot.


Not used on this Example.


  1. Prepare HW like described on section TE0808 StarterKit#Programming
  2. Connect UART USB (JTAG XMOD)
  3. Select SD Card as Boot Mode (or QSPI - depending on step 1)
    Note: See TRM of the Carrier, which is used.
  4. (Optional) Insert PCIe Card (detection depends on Linux driver. Only some basic drivers are installed)
  5. (Optional) Connect Sata Disc
  6. (Optional) Connect DisplayPort Monitor (List of usable Monitors:
  7. (Optional) Connect Network Cable
  8. Power On PCB
    Note: 1. ZynqMP Boot ROM loads PMU Firmware and  FSBL from SD into OCM, 2. FSBL loads ATF(bl31.elf) and U-boot from SD/QSPI into DDR, 3. U-boot load Linux from SD into DDR.


  1. Open Serial Console (e.g. putty)
    1. Speed: 115200
    2. COM Port: Win OS, see device manager, Linux OS see  dmesg |grep tty  (UART is *USB1)
  2. Linux Console:
    Note: Wait until Linux boot finished For Linux Login use:
    1. User Name: root
    2. Password: root
  3. You can use Linux shell now.
  4. Debian Desktop
    1. Use connected mouse + keyboard for interaction with GUI
    2. Start the GUI with the command : startx
    3. Web Browser Dillo open console and type dillo or use browser
    4. open console and start video or audio with "mplayer <video or audio file>"
  5. Ubuntu Desktop
    1. Use connected mouse + keyboard for interaction with GUI
    2. Start the GUI with the command : startx
    3. Web Browser Mozilla firefox can be used.
    4. Audio or Vider file can also be performed directly in GUI

Hard Disk (optional)

To locate root file system on Hard disk:

  1. Plug in SD Card that you have prepared mit root file systemIt will automatically in BOOT directory two DTB file generated
  2. Plug in Hard Disk in Sata port on the carrier board
  3. Format the hard disk by the following command:
    1. mkfs.ext4 /dev/sda
  4. Edit the fstab file in directory /etc/ to mount hard disk by the following commands:
    1. mkdir /media/harddisk
    2. nano /etc/fstab
    3. Add this line to the fstab file and save it : /dev/sda  /media/harddisk/   defaults  0  3
    4. Reboot
  5. Copy entire root file system in directory ROOTFS from SD card to hard disk by the following commands:
    1. cd /media/ROOTFS
    2. cp -r ./ /media/harddisk
  6. Edit the fstab file in directory /media/harddisk/etc/ by the following commands and save it:
    1. nano /media/harddisk/etc/fstab
    2. Edit this line to the fstab file : /dev/sda  /media/harddisk/   defaults  0  1
    3. Comment this line: #/dev/mmcblk1p2   /media/ROOTFS     defaults  0  1
  7. Shutdown the system
  8. Format the SD card
  9. Rename the Device Tree Blob file system_harddisk.dtb to system.dtb
  10. Copy the following files to SD Card:
    1. Image
    2. BOOT.bin
    3. system.dtb
  11. Plug in the SD Card and turn on the system

Vivado Hardware Manager

System Design - Vivado

Block Design

Block Design

PS Interfaces

Activated interfaces:

PS Interfaces


Basic module constrains

set_property BITSTREAM.GENERAL.COMPRESS TRUE [current_design]
set_property BITSTREAM.CONFIG.UNUSEDPIN PULLNONE [current_design]

#System Controller IP
  #LED_HD SC0 J3:31
  #LED_XMOD SC17 J3:48 
  #CAN RX SC19 J3:52 B47_L2_P in
  #CAN TX SC18 J3:50 B47_L2_N out 
  #CAN S  SC16 J3:46 B47_L3_N out
set_property PACKAGE_PIN J14 [get_ports BASE_sc0]
set_property PACKAGE_PIN G13 [get_ports BASE_sc5]
set_property PACKAGE_PIN J15 [get_ports BASE_sc6]
set_property PACKAGE_PIN K15 [get_ports BASE_sc7]
set_property PACKAGE_PIN A15 [get_ports BASE_sc10_io]
set_property PACKAGE_PIN B15 [get_ports BASE_sc11]
set_property PACKAGE_PIN C13 [get_ports BASE_sc12]
set_property PACKAGE_PIN C14 [get_ports BASE_sc13]
set_property PACKAGE_PIN E13 [get_ports BASE_sc14]
set_property PACKAGE_PIN E14 [get_ports BASE_sc15]
set_property PACKAGE_PIN A13 [get_ports BASE_sc16]
set_property PACKAGE_PIN B13 [get_ports BASE_sc17]
set_property PACKAGE_PIN A14 [get_ports BASE_sc18]
set_property PACKAGE_PIN B14 [get_ports BASE_sc19]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc0]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc5]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc6]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc7]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc10_io]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc11]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc12]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc13]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc14]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc15]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc16]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc17]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc18]
set_property IOSTANDARD LVCMOS18 [get_ports BASE_sc19]

#set_property PACKAGE_PIN AH6 [get_ports {si570_clk_p[0]}]
#set_property IOSTANDARD LVDS [get_ports {si570_clk_p[0]}]
#set_property IOSTANDARD LVDS [get_ports {si570_clk_n[0]}]
# Clocks
#set_property PACKAGE_PIN J8 [get_ports {B229_CLK1_clk_p[0]}]
#set_property PACKAGE_PIN F25 [get_ports {B128_CLK0_clk_p[0]}]
# SFP 
#set_property PACKAGE_PIN G8 [get_ports {B230_CLK0_clk_p}]
# B230_RX3_P
#set_property PACKAGE_PIN A4 [get_ports {SFP1_rxp}]
# B230_TX3_P
#set_property PACKAGE_PIN A8 [get_ports {SFP1_txp}]
# B230_RX2_P
#set_property PACKAGE_PIN B2 [get_ports {SFP2_rxp}]
# B230_TX2_P
#set_property PACKAGE_PIN B6 [get_ports {SFP2_txp}]

# Audio Codec
#LRCLK		  J3:49 B47_L9_N
#BCLK		    J3:51 B47_L9_P
#DAC_SDATA	J3:53 B47_L7_N
#ADC_SDATA	J3:55 B47_L7_P
set_property PACKAGE_PIN G14 [get_ports I2S_lrclk ]
set_property PACKAGE_PIN G15 [get_ports I2S_bclk ]
set_property PACKAGE_PIN E15 [get_ports I2S_sdin ]
set_property PACKAGE_PIN F15 [get_ports I2S_sdout ]
set_property IOSTANDARD LVCMOS18 [get_ports I2S_lrclk ]
set_property IOSTANDARD LVCMOS18 [get_ports I2S_bclk ]
set_property IOSTANDARD LVCMOS18 [get_ports I2S_sdin ]
set_property IOSTANDARD LVCMOS18 [get_ports I2S_sdout ]

Software Design - Vitis

For SDK project creation, follow instructions from:



SDK template in ./sw_lib/sw_apps/ available.


TE modified 2019.2 FSBL


  • Modified Files: xfsbl_main.c, xfsbl_hooks.h/.c, xfsbl_board.h/.c(search for 'TE Mod' on source code)
  • Add Files:  te_xfsbl_hooks.h/.c (for hooks and board)\n\
  • General Changes: 
    • Display FSBL Banner and Device Name

Module Specific:

  • Add Files: all TE Files start with te_*
    • Si5345 Configuration
    • OTG+PCIe Reset over MIO
    • I2C MUX for EEPROM MAC


TE modified 2019.2 FSBL


  • Modified Files: xfsbl_initialisation.c, xfsbl_hw.h, xfsbl_handoff.c, xfsbl_main.c
  • General Changes:
    •  Display FSBL Banner
    • Set FSBL Boot Mode to JTAG
    • Disable Memory initialisation


Xilinx default PMU firmware.


Hello TE0808 is a Xilinx Hello World example as endless loop instead of one console output.


U-Boot.elf is generated with PetaLinux. Vitis is used to generate Boot.bin.

Software Design -  PetaLinux

For PetaLinux installation and  project creation, follow instructions from:


Start with petalinux-config or petalinux-config --get-hw-description

Select Image Packaging Configuration ==> Root filesystem type ==> Select SD Card



  • CONFIG_SUBSYSTEM_USER_CMDLINE="console=ttyPS0,115200 earlycon clk_ignore_unused earlyprintk root=/dev/mmcblk1p2 rootfstype=ext4 rw rootwait cma=1024M"















Start with petalinux-config -c u-boot

  • # CONFIG_ENV_IS_IN_SPI_FLASH is not set










Device Tree

/include/ "system-conf.dtsi"
/ {
  chosen {
    	xlnx,eeprom = &eeprom;
		bootargs= "console=ttyPS0,115200 earlycon clk_ignore_unused earlyprintk root=/dev/mmcblk1p2 rootfstype=ext4 rw rootwait cma=1024M";
		/* notes: root=/dev/mmcblk1p2 for SD and root=/dev/sda for hard disk will be changed automatically by executing the debian/ubuntu script*/

/* notes:
serdes: // PHY TYP see: dt-bindings/phy/phy.h

/* default */

/* SD */

&sdhci1 {


/* USB  */

&dwc3_0 {
    status = "okay";
    dr_mode = "host";
    phy-names = "usb2-phy","usb3-phy";
    phys = <&lane1 4 0 2 100000000>;
    maximum-speed = "super-speed";

/* ETH PHY */

&gem3 {
	phy-handle = <&phy0>;
	phy0: phy0@1 {
		device_type = "ethernet-phy";
		reg = <1>;

/* QSPI */

&qspi {
    #address-cells = <1>;
    #size-cells = <0>;
    status = "okay";
    flash0: flash@0 {
        compatible = "jedec,spi-nor";
        reg = <0x0>;
        #address-cells = <1>;
        #size-cells = <1>;

/* I2C */

&i2c0 {
    i2cswitch@73 { // u
        compatible = "nxp,pca9548";
        #address-cells = <1>;
        #size-cells = <0>;
        reg = <0x73>;
        i2c@0 { // MCLK TEBF0808 SI5338A, 570FBB000290DG_unassembled
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <0>;
        i2c@1 { // SFP TEBF0808 PCF8574DWR
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <1>;
        i2c@2 { // PCIe
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <2>;
        i2c@3 { // SFP1 TEBF0808
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <3>;
        i2c@4 {// SFP2 TEBF0808
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <4>;
        i2c@5 { // TEBF0808 EEPROM
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <5>;
            eeprom: eeprom@50 {
	            compatible = "atmel,24c08";
	            reg = <0x50>;
        i2c@6 { // TEBF0808 FMC  
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <6>;
        i2c@7 { // TEBF0808 USB HUB
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <7>;
    i2cswitch@77 { // u
        compatible = "nxp,pca9548";
        #address-cells = <1>;
        #size-cells = <0>;
        reg = <0x77>;
        i2c@0 { // TEBF0808 PMOD P1
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <0>;
        i2c@1 { // i2c Audio Codec
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <1>;
            adau1761: adau1761@38 {
                compatible = "adi,adau1761";
                reg = <0x38>;
        i2c@2 { // TEBF0808 Firefly A
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <2>;
        i2c@3 { // TEBF0808 Firefly B
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <3>;
        i2c@4 { //Module PLL Si5338 or SI5345
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <4>;
        i2c@5 { //TEBF0808 CPLD
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <5>;
        i2c@6 { //TEBF0808 Firefly PCF8574DWR
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <6>;
        i2c@7 { // TEBF0808 PMOD P3
            #address-cells = <1>;
            #size-cells = <0>;
            reg = <7>;


Start with petalinux-config -c kernel


  • CONFIG_CPU_IDLE is not set (only needed to fix JTAG Debug issue)

  • CONFIG_CPU_FREQ is not set (only needed to fix JTAG Debug issue)



Applications will be generated with Debian script or Ubuntu script (


Applications will be generated with Debian script or Ubuntu script (

Additional Software

No additional software is needed.


File location <design name>/misc/Si5345/Si5345-*.slabtimeproj

General documentation how you work with these project will be available on Si5345

Appx. A: Change History and Legal Notices

Document Change History

To get content of older revision  got to "Change History"  of this page and select older document revision number.

DateDocument Revision



  • Typo
2020-05-11v.1Mohsen Chamanbaz
  • 2019.2 release
Document change history.

Legal Notices

Data Privacy

Please also note our data protection declaration at

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.



Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).


Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.


Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.

  • No labels