Versions Compared

Old Version 16

changes.mady.by.user Mohsen Chamanbaz

Saved on

compared with

New Version 17

changes.mady.by.user Mohsen Chamanbaz

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Scroll Title
anchorTable_AHW
titleAdditional Hardware

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Additional HardwareNotes
Micro USB Cable for JTAG/UART
Cooler

It

's recommended to use cooler on Zynqmp RFSoC  device

is strongly recommended that the RFSoC should not be used without heat sink.

SMA male connector cableSome ADC inputs/DAC outouts have the SMA connector
UFL female connector cableSome ADC inputs/DAC outouts have the UFL connector
Ethernet cable
SD card16GB
Signal generator (optional)To feed a desired signal to the input of ADC
Oscilloscope (optional)To monitor the output signal of DACs.
PCWith ATX Power supply and PCIe X8 slot


...

  1. Plug the TE0835 module on the TEB0835 carrier board
  2. Install the cooler on the RFSoC chip
    1. Attention: It is strongly recommended that the RFSoC should not be used without heat sink.
  3. Connect the micro USB cable to the J29 connector
  4. Plug the board on the PCIe port of the PC
  5. Plug the prepared SD card on the SD card socket (J28)
  6. Connect a cable with SMA or UFL connector to one of the DAC connector( for example DAC0 J9) and feed it back to the related ADC input (for example ADC0 J1)
  7. (optional) A signal generator can be used to feed desired sinal to ADC input.
  8. (optional) An oscilloscope can be used to monitor the output signal of DAC.

...

RF Analyzer GUIBoard TE0835 ( RFSoC U1)
TEB0835
Tile /ConverterSoC Pin NameSoC Pin NumberB2BSignal NameConnector DesignatorConnector Type
ADC Tile 0-ADC 01ADC0_P/ADC0_NAK2/AK1B2B31/29ADC0_P/ADC0_NJ1SMA
ADC Tile 0-ADC 23ADC1_P/ADC1_NAH2/AH1B2B43/41ADC1_P/ADC1_NJ2UFL
ADC Tile 1-ADC 01ADC2_P/ADC2_NAF2/AF1B2B49/47ADC2_P/ADC2_NJ3SMA
ADC Tile 1-ADC 23ADC3_P/ADC3_NAD2/AD1B2B59/61ADC3_P/ADC3_NJ4UFL
ADC Tile 2-ADC 01ADC4_P/ADC4_NAB2/AB1B2B67/65ADC4_P/ADC4_NJ5SMA
ADC Tile 2-ADC 23ADC5_P/ADC5_NY2/Y1B2B79/77ADC5_P/ADC5_NJ6UFL
ADC Tile 3-ADC 01ADC6_P/ADC6_NV2/V1B2B85/83ADC6_P/ADC6_NJ7SMA
ADC Tile 3-ADC 23ADC7_P/ADC7_NT2/T1B2B97/95ADC7_P/ADC7_NJ8UFL
DAC Tile 0-DAC 0DAC0_P/DAC0_NN2/N1B2B103/101DAC0_P/DAC0_NJ9SMA
DAC Tile 0-DAC 1DAC1_P/DAC1_NL2/L1B2B109/107DAC1_P/DAC1_NJ10UFL
DAC Tile 0-DAC 2DAC2_P/DAC2_NJ2/J1B2B121/119DAC2_P/DAC2_NJ11SMA
DAC Tile 0-DAC 3DAC3_P/DAC3_NG2/G1B2B127/125DAC3_P/DAC3_NJ12UFL
DAC Tile 1-DAC 0DAC4_P/DAC4_NE2/E1B2B133/131DAC4_P/DAC4_NJ13UFL
DAC Tile 1-DAC 1DAC5_P/DAC5_NC2/C1B2B139/137DAC5_P/DAC5_NJ14UFL
DAC Tile 1-DAC 2DAC6_P/DAC6_NB4/A4B2B151/149DAC6_P/DAC6_NJ15UFL
DAC Tile 1-DAC 3DAC7_P/DAC7_NB6/A6B2B157/155DAC7_P/DAC7_NJ16UFL

As an example the GUi should be seen after initialization as below:

Expand
titleOverview

For example, when all DACs are in operation, the GUI can be seen as below:

Expand
titleDACs

For example, when all ADCs are in operation, the GUI can be seen as below:

Expand
titleADCs




System Design - Vivado

...