Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Scroll Title
anchorFigure_PWR_PD
titlePower Distribution


Scroll Ignore
draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramDisplayName
lboxtrue
revision5
diagramNameTEB0835_PWR_PD
simpleViewerfalse
width639
linksauto
tbstylehidden
diagramWidth640


Scroll Only


...

Scroll Title
anchorFigure_PWR_PS
titlePower Sequency


Scroll Ignore


draw.io Diagram
borderfalse
diagramNameTEB0835_PWR_PS
simpleViewerfalse
width639
linksauto
tbstylehidden
diagramDisplayName
lboxtrue
diagramWidth641
revision1


Scroll Only


...

Scroll Title
anchorFigure_TS_PD
titlePhysical Dimension


Scroll Ignore
draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramDisplayName
lboxtrue
revision2
diagramNameTEB0835_TS_PD
simpleViewerfalse
width639
linksauto
tbstylehidden
diagramWidth641


Scroll Only
scroll-pdftrue
scroll-officetrue
scroll-chmtrue
scroll-docbooktrue
scroll-eclipsehelptrue
scroll-epubtrue
scroll-htmltrue


...

Scroll Title
anchorTable_RH_HRH
titleHardware Revision History

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DateRevisionChangesDocumentation Link
2019-11-29REV01Initial ReleaseREV01

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

2020-08-13REV02
  1. All module's mount holes are connected to GND;
  2. CLK_Connectors. Added baluns for each clock inputs;
  3. Internal DSPLL is changed on SI5395A-A-GM;
  4. Added ability to use internal DSPLL as a source for each clock;
  5. Added clock inputs CLKIN1, CLKIN2 and clock outputs OUT1 , OUT2 connected to DSPLL.;
  6. All clock traces are matched with tolerance 0.2 mm;
  7. Lengths of inputs ADC0, ADC2, ADC4, ADC6 are matched with tolerance 0.2 mm;
  8. Lengths of outputs DAC0 and DAC2 are matched with tolerance 0.2 mm;
  9. Lengths of outputs DAC4, DAC5, DAC6, DAC7 are matched with tolerance 0.2 mm;
  10. In REV02: FTDI is powered from 3.3V_Module;
  11. Signal PLL_INTR_N is removed;
  12. Signal BOARD_PG is renamed in MODULE_PG;
  13. Added ability to select enable signal for internal DC-DCs 3.3V and 1.8V.
  14. Added JTAG connector J40.
  15. Added VBAT schematic. Added a holder for CR1220 3V battery
REV02



Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Scroll Title
anchorFigure_RV_HRN
titleBoard hardware revision number.


Scroll Ignore
draw.io Diagram
border
Scroll Title
anchorFigure_RV_HRN
titleBoard hardware revision number.
Scroll Ignore
draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramDisplayName
lboxtrue
revision24
diagramNameTEB0835_RV_HRN
simpleViewerfalse
width200
linksauto
tbstylehidden
diagramWidth201


Scroll Only



...

Scroll Title
anchorTable_RH_DCH
titleDocument change history.

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DateRevisionContributorDescription

Page info
infoTypeModified date
dateFormatyyyy-MM-dd
typeFlat

Page info
infoTypeCurrent version
prefixv.
typeFlat
showVersionsfalse

Page info
infoTypeModified by
typeFlat
showVersionsfalse

  • Update to 
    Revision 02Initial Release

--

all

Page info
infoTypeModified users
typeFlat
showVersionsfalse

  • --


...