Versions Compared

Old Version 79

changes.mady.by.user John Hartfiel

Saved on

compared with

New Version 80

changes.mady.by.user John Hartfiel

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

The Trenz Electronic TE0701 Carrier Board is a baseboard for 4 x 5 SoMs, which exposes the module's B2B connector pins to accessible connectors and provides a whole range of on-board components to test and evaluate TE 4 x 5 SoMs.

See page "4 x 5 cm carriers" to get information about the SoMs supported by the TE0701 carrier board.

Refer to http://trenz.org/te0701-info for the current online version of this manual and other available documentation.

...

  1. HDMI connector (1.4 HEAC support), J4
  2. Micro-USB2 connector, J12

  3. Pmod connector, J5

  4. Pmod connector, J6
  5. User push-button ("RESTART" button by default), S2
  6. User push-button ("RESET" button by default), S1
  7. 8x red user LEDs, D1 ... D8
  8. Mini-USB2 connector, J7
  9. User 4-bit DIP switch, S3
  10. VITA 57.1 compliant LPC FMC connector, J10
  11. Barrel jack for 12V power supply, J13
  12. ARM JTAG connector (DS-5 D-Stream), J15, functionality depends on module
  13. User 4-bit DIP switch, S4
  14. Pmod connector, J1
  15. RJ45 Gigabit Ethernet connector, J14
  16. SD Card connector, J8
  17. Pmod connector, J2
  18. Jumper, J18
  19. Mini CameraLink connector, J3
  20. CR1220 Backup-Battery holder, B1
  21. Trenz Electronic 4 x 5 modules B2B connectors, JB1 ... JB3
  22. Jumper J16, J17, J21
  23. Jumper J9, J19, J20
  24. Analog Devices ADV7511 HDMI Transmitter, U1
  25. Lattice Semiconductor MachXO2 1200 HC System Controller CPLD, U14
  26. FTDI FT2232H USB2 to JTAG/UART Bridge, U3

...

Page properties
hiddentrue
idComments

Notes:

  • For carrier or stand-alone boards use subsection for every connector typ (add designator on description, not on the subsection title), for example:
    • SD
    • USB
    • ETH
    • FMC
    • ...
  • For modules which needs carrier us only classes and refer to B2B connector if more than one is used, for example
    • JTAG
    • UART
    • I2C
    • MGT
    • ...

FMC LPC Connector

I/O signals and interfaces connected to the FPGA SoCs I/O bank and FMC connector J10:

Scroll Title
anchorTable_SIP_FMC
titleFMC connector J10 interface

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

FMC Connector J2 Pins and InterfacesI/O Signal CountLVDS-pairs countConnected toVCCIO voltageNotes
I/O3417B2B JB1 connectorFMC_VADJ / 3V3_FMCpins usable as single ended I/O's and LVDS pairs
3417B2B JB2 connectorFMC_VADJ / 3V3_FMC
I²C2-SC CPLD U14, pin 8, 10-FMC I²C Geographical Address pins GA0 and GA1 set to GND.
JTAG4-SC CPLD U14, pin 4, 7, 9, 123.3V-
Clock Input-2B2B JB1 connector-2x bidirectional reference clock inputs
Control Signals2-SC CPLD U14, pin 20, 28-

'PG_C2M',  'FMC_PRSNT'

Reference voltage (FMC_VREF)1-B2B JB1 connector, pin 85, 97
B2B JB2 connector, pin 37, 93		-FMC sets thresholds of attached module's reference voltage (VREF pins).


...

There are two baseboard supply voltages VIOTA and VIOTB connected to the 4 x 5 SoM's PL IO-bank. The supply-voltages have following pin assignments on B2B-connectors:

...

Scroll Title
anchorTable_RH_DCH
titleDocument change history

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DateRevisionAuthorsDescription

Page info
modified-date
modified-date
dateFormatyyyy-MM-dd

Page info
infoTypeCurrent version
prefixv.
typeFlat
showVersionsfalse



Page info
infoTypeModified by
typeFlat
showVersionsfalse

  • Corrected USB J9 description
  • Typos
  • update Button description
  • Note for J15

2019-01-11

v.73
John Hartfiel
  • correction temperature range

2018-10-22

Oct 2018

v.72Ali Naseri
  • General TRM revision and updated to new style
2018-06-13


v.66

Ali Naseri
  • updated Power-on sequence diagram
2018-01-12

v.62

John Hartfiel
  • Dual PMOD note
2017-11-09v.60John Hartfiel
  • add B2B connector section
2017-08-15

v.59

John Hartfiel
  • Add VCCIO Jumper Pin location.
  • Updated VADJ description.
2017-08-14v.58John Hartfiel
  • Description correction.
2017-05-25v.56Jan Kumann
  • New physical dimensions drawing of the board.
2017-05-16

v.51

Jan Kumann
  • A few overall improvements and corrections, new  block diagram.
2017-04-11


Ali Naseri
  • added block diagram
2017-02-15

v.45

Ali Naseri
  • added warning concerning the use of FTDI tools
2017-02-15v.40Ali Naseri
  • added power-on sequence diagram
2017-01-19

v.35

Ali Naseri
  • correction of table 3 (switch-positions to adjust FMC_VADJ)
  • inserted hint to set and measure the PL IO-bank supply-voltages
2017-01-13

v.20

Ali Naseri
  • added section for baseboard supply voltage configuration
2016-11-29
v.10


Ali Naseri
  • TRM update due to new revision 06 of
  • the carrier board.
2016-11-28v.4

Ali Naseri

  • TRM adjustment to the newest
  • revision (05) of TE0701 Carrier Board.
2014-02-18
0.2
Sven-Ole Voigt
  • TE0701-03 (REV3) updated
2014-01-05

0.1

Sven-Ole Voigt
  • Initial release


...