Page History

...

Online version of this manual and other related documents can be found at https://wiki.trenz-electronic.de/display/PD/TE0701

See page "4 x 5 cm carriers" to get information about the SoMs supported by the TE0701 Carrier Board.

...

Figure 1: 4x5 SoM carrier board TE0701-06

TE0701-05 (REV 06):

1. HDMI Connector (1.4 HEAC Support)
2. Micro USB Connector (Device, Host or OTG Modes)

3. Pmod Connector for Zynq-module PL (4 LVDS-pairs, max. VCCIO-voltage VIOTA)

4. Pmod Connector for Zynq-module PL (4 LVDS-pairs, max. VCCIO-voltage FMC_VADJ)
5. User Push Button S2 ("RESTART" button by default)
6. User Push Button S1 ("RESET" button by default)
7. User LEDs (function mapping depends on firmware of System-Controller-CPLD)
8. Mini USB Connector (USB JTAG and UART Interface)
9. User 4-bit DIP Switch
10. VITA 57.1 compliant FMC LPC Connector with digitally programmable FMC VADJ Power Supply
11. Barrel jack for 12V Power Supply
12. ARM JTAG Connector (DS-5 D-Stream) - PJTAG to EMIO multiplexing needed
13. User 4-bit DIP Switch (provides the possibility to set voltage FMC_VADJ)
14. Pmod Connector (J1, 3.3V): mapped to 8 Zynq PS MIO0-bank-pins (MIO0, MIO9 to MIO15) when using TE0720 (same mapping as on Zedboard), 6 pins (MIO10 to MIO15) are additionally connected to TE0701 System-Controller-CPLD
15. RJ45 GbE Connector
16. SD Card Connector - Zynq SDIO0 Bootable SD port
17. Pmod Connector (J2, 3.3V): 6 pins (PX0 to PX5) can be multiplexed by Texas Instruments TXS02612RTWR SDIO Port Expander to MIO-pins of Zynq-module, 2 pins are connected to TE0701 System-Controller-CPLD (PX6 and PX7)
18. Jumper J18
19. Mini CameraLink Connector
20. Battery holder for CR1220 (RTC backup voltage)
21. Trenz 4x5 module Socket (3x Samtec LSHM Series Connectors)
22. Jumper J16, J17, J21
23. Jumper J9, J19, J20

...

• Overvoltage-, undervoltage- and reversed- supply-voltage-protection
• Barrel jack for 12V power supply
• Carrier Board System-Controller-CPLD Lattice MachXO2 1200HC, programable by Mini-USB JTAG-Interface J7
• Zynq-module programable by ARM-JTAG-Interface-Connector (J15) or by System-Controller-CPLD via Mini-USB JTAG-Interface J7 or JTAG-Interface on FMC-Connector J10
• Mini CameraLink
• RJ45 Gigabit Ethernet Jack with 2 integrated LEDs.
• FPGA Mezzanine Card (FMC) Connector J10 for acces to Zynq-Module's LVDS-pairs, operable with adjustable IO-voltage FMC_VADJ
  
• USB JTAG- and UART-Interface (FTDI FT2232HQ) with Mini-USB-Connector J7
• ADV7511 HDMI Transmitter with HDMI-Connector J4
  
• 8 x user LEDs routed to System-Controller-CPLD, 8 x red
• 2 x user-push button routed to System-Controller-CPLD; by default configured as system "RESET" and "RESTART" button (depends on CPLD-Firmware)
  
• 2 x 4-bit DIP-Switch for base-board-configuration (3 switches routed to System-Controller-CPLD, 3 switches to set voltage FMC_VADJ, 1 switch routed to Zynq-module (MIO0), 1 switch enables Mini-USB JTAG-Interface J7)
  
• PMOD-Connectors to access Zynq-Module's LVDS-pairs and MIO-Pins
  
• Micro SD card socket, can be used to boot system
• Micro-USB-Interface (J12) connected to Zynq-module (Device, Host or OTG modes)
• Trenz 4x5 module Socket (3 x Samtec LSHM series connectors)

Interfaces and Pins

Board to Board (B2B) I/O's

...

Micro SD Card Socket

Micro SD Card socket is not directly wired to the B2B connector pins, but through a Texas Instruments TXS02612 SDIO Port Expander, which is needed for voltage translation due to different voltage levels of the Micro SD Card and MIO-bank of the Xilinx Zynq-module. The Micro SD Card has 3.3V signal voltage level, but the MIO-bank on the Xilinx Zynq-module has VCCIO 1.8V.

...