Page History
...
base-board supply-voltages | base-board B2B connector-pins | standard assignment of PL IO-bank supply-voltages on TE 4x5 module's B2B connectors | base-board voltages and signals connected with |
|---|---|---|---|
| VIOTA | JB2-2, JB2-4, JB2-6 | VCCIOB (JM2-1, JM2-3) / VCCIOC (JM2-5) | HDMI_SCL, HDMI_SDA, HDMI_INT, J5 VCCIO |
| VIOTB | JB1-10, JB1-12, JB2-8, JB2-10 | VCCIOA (JM1-9, JM1-11) / VCCIOD (JM2-7, JM2-9) | VCCIO1 (System-Controller-CPLD pin 55, 73) |
Table 4: base-board supply-voltages VIOTA and VIOTB
| Note |
|---|
Note: The corresponding PL IO-voltage supply voltages of the 4x5 SoM to the selectable base-board voltages VIOTA and VIOTB are depending on the mounted 4x5 SoM and varying in order of the used model. Refer to SoM's schematic to get information about the specific pin assignment on module's B2B-connectors regarding PL IO-bank supply voltages and to the 4x5 Module integration Guide for VCCIO voltage options. |
Following table gives the conjunction between the base-board supply-voltages VIOTA, VIOTB and the PL IO-bank's voltages of 4x5 SoMs:
supported 4x5 SoMs vs base-board VCCIO | TE0710 | TE0711 | TE0712 | TE0713 | TE0715-xx-15 | TE0715-xx-30 | TE0720 | TE0741 | TE0841 |
|---|---|---|---|---|---|---|---|---|---|
| VIOTA | NC | B34 (VCCIOB) | B13 (VCCIOB) | B13 (VCCIOB) | B34 (VCCIOC) | B34 (HP bank, VCCIOC) | B33 (VCCIOC) B34 (VCCIOB) | B15 (VCCIOC) B16 (VCCIOB) | B66 (HP bank, VCCIOB) B68 (HP bank, VCCIOC) |
| VIOTB | B15 (VCCIOA) B34 (VCCIOD) | B15 (VCCIOA) B35 (VCCIOD) | B16 (VCCIOA) B15 (VCCIOD) | B16 (VCCIOA) B15 (VCCIOD) | B13 (VCCIOA) B35 (VCCIOD) | B13 (VCCIOA) B35 (HP bank, VCCIOD) | B35 (VCCIOA) B13 (VCCIOD) | B13 (VCCIOA) B12 (VCCIOD) | B64 (VCCIOA) B67 (HP bank, VCCIOD) |
Table 5: base-board supply-voltages VIOTA and VIOTB in conjunction with PL IO-bank voltages
Following table describes how to configure the base-board supply-voltages by jumpers:
base-board supply-voltages vs voltage-levels | VIOTA | VIOTB | USB-VBUS | 12V0_CL |
|---|---|---|---|---|
| 3V3 | J17:1-2, 3 & J16: open | J17: 1-2, 3 & J16: open & J21:1-2, 3 | - | - |
| 2V5 | J17:1, 2-3 & J16: open | J17:1, 2-3 & J16: open & J21: 1-2, 3 | - | - |
| FMC_VADJ | J17: open & J16: 1-2 | J21:1, 2-3 | - | - |
| 5V0 intern | - | - | J9:1-2, 3 & J19: 1-2 (J20: 1-2: additional decoupling-capacitor 100 µF) | - |
| Vbus extern | - | - | J9: 1, 2-3 & J19: open | - |
| 12V_LC | - | - | - | J18: 1-2 |
Table 6: Configuration of base-board supply-voltages via jumpers. Jumper-Notification: 'Jx: 1-2, 3' means pins 1 and 2 are connected, 3 is open. 'Jx: 1, 2-3' means pins 2 and 3 are connected, 1 is open
| Note |
|---|
| It is recommended to set and measure the PL IO-bank supply-voltages before mounting of TE 4x5 module to avoid failures and damages to the functionality of the mounted SoM. |
...
Overview
Content Tools